Engineering Commons^™

A Study On High-Frequency Bending Fatigue, Microhardness, Tensile Strength, And Microstructure Of Parts Made Using Atomic Diffusion Additive Manufacturing (Adam) And Additive Friction Stir Deposition (Afsd), Hamed Ghadimi

LSU Doctoral Dissertations

This dissertation reports the findings of several studies on the mechanical and microstructural properties of parts made using atomic diffusion additive manufacturing (ADAM) and additive friction stir deposition (AFSD). The design of a small-sized bending-fatigue test specimen for an ultrasonic fatigue testing system is reported in Chapter 1. The design was optimized based on the finite element analysis and analytical solution. The stress–life (S–N) curve is obtained for Inconel alloy 718. Chapter 2 presents the findings of ultrasonic bending-fatigue and tensile tests carried out on the ADAM test specimens. The S-N curves were created in the very high-cycle fatigue regime. …

Mechanical Properties And Microstructure Of High Strength Lc3 Pastes With Varying Limestone/Calcined Clay Ratios And Different Curing Conditions, Yemin Dong

International Conference on Durability of Concrete Structures

研究（抗施工蒸馏）石石和石榴石在淀粉胶系统（即0标准和低水印）下的水胶系统（即0标准和低水墨）X射线比、水量值水量-电子背基相关研究.61.25 .25.25.25.0.25.25.25.25.25.0.25.25.25.25.25.1.25.7.25.0.0.0.0.0.0.0.0.0.0.0.0.0.0.1.25.1.25.25.1.25.1.25.1.25.1.25.1.25.1 .25.1.25.1.25.1.25.1.25.1.25.0.0.0.0.0.0.0.00.0.0.1.25.1.25.1.25.1.25.1.25.0.0.0.00.0.0.0.0.0.0.0.0.0.0.0.0.0.00.0 .00.0.00.X射线比值、水量-电子显微镜相关研究测量值。早期的水泥水化程度小水的压合含煤量，降低了水泥石的。因此，需要采用合适的钙铝内容和体系以提高碳系统的性能。

Investigation On Structural Heritability And Durability Of High Sulfate Resistance Portland Cement Mortar Modified By Aluminum Salt, Jun Xu

International Conference on Durability of Concrete Structures

The essential hydration and hardened properties of high sulfate resistance Portland cement paste/mortar were investigated with Al₂(SO₄)₃ as admixture. Experiment results showed that that the addition of Al₂(SO₄)₃ promoted the hydration of HSRP cement pastes, and the hydration rate accelerated with the increase of the addition amount. The mechanical properties and chloride diffusion coefficient of cement mortar were obviously improved with 0.25% Al₂(SO₄)₃ addition . For instance, the compressive strength of AS0.25 cement mortars was 24.8% higher than AS0 samples and the chloride ion migration …

Production Of Low-Cost Self-Consolidating Concrete (Scc) Using Manufactured Aggregates, Rabab Raydan, Farah Chamseddine, Ali Jahami, Oussama Baalbaki, Jamal Khatib, Adel Elkordi

BAU Journal - Science and Technology

Limitations to the sources of aggregates and the unavailability of sand is becoming a problematic issue for concrete production. A novel technology of manufactured aggregates can produce well graded round aggregates that can substitute natural aggregates while maintaining the same characteristics needed and preserving the resources. Self-Consolidating Concrete (SCC) using manufactured aggregates is assessed in this experimental work to understand the variability of workability properties and mechanical properties with the changes in w/c ratio and percentages of Coarse Aggregates and Manufactured Sand to Natural Sand in order to choose the best mixture that satisfies an adequate overall performance. Targeting compressive …

Strengthening Of 7175 Aluminum Alloy Through Multi-Step Aging Process, Colin E. Masterson, Ryland W. Jolliffe

Materials Engineering

7175 is a heat-treatable aluminum alloy commonly used in aerospace forgings. This alloy is aged with a multi-step heat treatment. This treatment must balance strength with stress corrosion cracking resistance through a degree of overaging. The team was tasked by Weber Metals to increase the strength of this treatment without sacrificing stress corrosion cracking resistance. Both two-step and retrogression and reaging treatments were tested in experiments to find a heat treatment that could increase the yield and tensile strength by 1-2 ksi while maintaining a minimum electrochemical conductivity equivalence of 38% relative to copper. Two-step aging is the more conventional …

Enhancement Of Asphalt Performance By Graphene-Based Bitumen Nanocomposites, Sara Moghtadernejad, Ehsan Barjasteh, Ren Nagata, Haia Malabeh

Mineta Transportation Institute Publications

As the State of California continues to grow, demand for enhanced infrastructure such as roadways and highways escalates. In view of the current average highway lifespan of 15–20 years, the improvement of asphalt binders leads to material sustainability by decreasing required maintenance and increasing the lifespan of roadways. In the present investigation, enhancement of asphalt binder properties was achieved by different methods of mixing varying compositions of graphene nanoparticles with an SBS polymer and asphalt binder. Additionally, experimental evaluation and comparison of the rheological and mechanical properties of each specimen is presented. Graphene nanoparticles have attracted great curiosity in the …

Boron Nitride Nanotube Based Lightweight Metal Matrix Composites: Microstructure Engineering And Stress-Transfer Mechanics, Pranjal Nautiyal

FIU Electronic Theses and Dissertations

Lightweight metals, such as Aluminum, Magnesium and Titanium, are receiving widespread attention for manufacturing agile structures. However, the mechanical strength of these metals and their alloys fall short of structural steels, curtailing their applicability in engineering applications where superior load-bearing ability is required. There is a need to effectively augment the deformation- and failure-resistance of these metals without compromising their density advantage.

This dissertation explores the mechanical reinforcement of the aforementioned lightweight metal matrices by utilizing Boron Nitride Nanotube (BNNT), a 1D nanomaterial with extraordinary mechanical properties. The nanotubes are found to resist thermo-oxidative transformations up to ~750°C, establishing their …

Molecular Modeling Of Aerospace Polymer Matrices Including Carbon Nanotube-Enhanced Epoxy, Matthew Radue

Dissertations, Master's Theses and Master's Reports

Carbon fiber (CF) composites are increasingly replacing metals used in major structural parts of aircraft, spacecraft, and automobiles. The current limitations of carbon fiber composites are addressed through computational material design by modeling the salient aerospace matrix materials. Molecular Dynamics (MD) models of epoxies with and without carbon nanotube (CNT) reinforcement and models of pure bismaleimides (BMIs) were developed to elucidate structure-property relationships for improved selection and tailoring of matrices.

The influence of monomer functionality on the mechanical properties of epoxies is studied using the Reax Force Field (ReaxFF). From deformation simulations, the Young’s modulus, yield point, and Poisson’s ratio …

Influence Of Pre-Stretching On The Subsequent Creep Aging Behavior Of Aluminum Alloy 2524, Yongqian Xu, Lihua Zhan, Minghui Huang, Youliang Yang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Low-Temperature Bainite Transformation Behavior And Microstructure And Mechanical Properties Of A Medium-Carbon High-Strength Steel For Railway Forging Upper Core Plate, Xiaofeng Qin, Shihai Cui, An Wang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Mechanical Properties Of Stainless Steels With Heterogeneous Nanostructures, Hiromi Miura, Masakazu Kobayashi, Natuko Sugiura, Naoki Yoshinaga

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Improving The Capacity, Durability And Stability Of Lithium-Ion Batteries By Interphase Engineering, Qinglin Zhang

Theses and Dissertations--Chemical and Materials Engineering

This dissertation is focus on the study of solid-electrolyte interphases (SEIs) on advanced lithium ion battery (LIB) anodes. The purposes of this dissertation are to a) develop a methodology to study the properties of SEIs; and b) provide guidelines for designing engineered SEIs. The general knowledge gained through this research will be beneficial for the entire battery research community.

The Influence Of Heterogeneous Meninges On The Brain Mechanics Under Primary Blast Loading, Linxia Gu, Mehdi S. Chafi, Shailesh Ganpule, Namas Chandra

Department of Mechanical and Materials Engineering: Faculty Publications

In the modeling of brain mechanics subjected to primary blast waves, there is currently no consensus on how many biological components to be used in the brain–meninges–skull complex, and what type of constitutive models to be adopted. The objective of this study is to determine the role of layered meninges in damping the dynamic response of the brain under primary blast loadings. A composite structures composed of eight solid relevant layers (including the pia, cerebrospinal fluid (CSF), dura maters) with different mechanical properties are constructed to mimic the heterogeneous human head. A hyper-viscoelastic material model is developed to better represent …

Performance Of Nevada’S Aggregates In Alkali-Aggregate Reactivity Of Portland Cement Concrete, Mohammad Shahidul Islam

UNLV Theses, Dissertations, Professional Papers, and Capstones

Alkali-aggregate reaction (AAR) is a form of distress that occurs in concrete and results in serviceability problems, cracks, spalling, and other deterioration mechanisms. There are two categories of AAR, namely, alkali-silica reaction (ASR) and alkali-carbonate reaction (ACR). Alkali-silica reaction is one of the most recognized deleterious phenomena in concrete, and has been a major concern since its discovery in the 1940s. The reaction which occurs between reactive silica or silicates present in some aggregates and alkalis of Portland cement produces an alkali-silica gel that expands in the presence of moisture resulting in concrete cracks. ACR is also a chemical reaction …