Engineering Commons^™

Anti-Washout Concrete: An Overview, Hao Lu, Xiao Sun, Hongyan Ma

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Anti-washout concrete (AWC) is a special cement-based material that can be directly employed in underwater environments without dispersion. It was developed around 50 years ago, and more than 150 journal articles and technical reports have been published. This paper provides a holistic review about the basic fresh-state and hardened-state properties of the AWC, such as water (washout) resistance, consistency, bleeding and segregation resistance, mechanical properties, and durability, as well as relevant testing methods. The discrepancies between AWC's characteristics and those of conventional concrete are clearly presented. The mixture compositions, supplementary cementitious materials (SCMs), and other conditions that affect AWC's performance …

Effects Of Organic Corrosion Inhibitors On The Performance Of Repair Mortars, Ominda Nanayakkara Dr.

International Conference on Durability of Concrete Structures

Reinforced concrete (RC) structures are severely degraded due to the corrosion of the embedded reinforcing steel, and hence, the upgrading of RC structures is essential. Repairing mortar is widely used to improve durability and strengthen structures; however, further repairing might be required considering the extended life of the structure. The use of inhibitors to protect the reinforcement from corrosion has become of great interest. Therefore, it is vital to study the potential of using corrosion inhibitors in a newly repaired system.

This study investigated the performance of a commercially available polymer-modified mortar with migrating and admixed corrosion inhibitors. The study …

Production Of Low-Cost Self-Consolidating Concrete (Scc) Using Manufactured Aggregates, Rabab Raydan, Farah Chamseddine, Ali Jahami, Oussama Baalbaki, Jamal Khatib, Adel Elkordi

BAU Journal - Science and Technology

Limitations to the sources of aggregates and the unavailability of sand is becoming a problematic issue for concrete production. A novel technology of manufactured aggregates can produce well graded round aggregates that can substitute natural aggregates while maintaining the same characteristics needed and preserving the resources. Self-Consolidating Concrete (SCC) using manufactured aggregates is assessed in this experimental work to understand the variability of workability properties and mechanical properties with the changes in w/c ratio and percentages of Coarse Aggregates and Manufactured Sand to Natural Sand in order to choose the best mixture that satisfies an adequate overall performance. Targeting compressive …

Use Of Saturated Lightweight Sand To Improve The Mechanical And Microstructural Properties Of Uhpc With Fiber Alignment, Huanghuang Huang, Le Teng, Xiaojian Gao, Kamal Khayat, Fazhou Wang, Zhichao Liu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper studied the influence of pre-saturated lightweight sand (LWS) on the mechanical and microstructural properties of UHPC cast with steel fiber alignment. The changes in hydration kinetics, porosity, nano-mechanical, and mechanical properties were studied. The LWS was used at 0–50% replacement volumes of total sand. Predominant fiber alignment was favored through a flow-induced casting method during casting of flexural prisms. Experiment results showed that the 28-d autogenous shrinkage was decreased from 450 to 275 μm/m with the LWS content increasing from 0 to 50%. The addition of 20% LWS led to maximum increases of 15%, 15%, and 20% in …

Development And Characterization Of Magnesium Phosphate Cement Based Ultra-High Performance Concrete, Jihui Qin, Fumin Dai, Hongyan Ma, Xiaobing Dai, Zhen Li, Xingwen Jia, Jueshi Qian

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study aims at the development of magnesium phosphate cement-based ultra-high performance concrete (MPC-UHPC). To this end, MPC paste phase was designed by using high magnesia-to-phosphate (M/P, 3.5) and low water-to-cement (W/C, 0.10–0.16) mass ratios, and certain amounts of ultra-fine fly ash (UFA, 5%–15%). Fresh and hardened properties, and microstructure of the developed MPC-UHPC were evaluated, and compared with those of conventional UHPC as well. Test results showed that lower W/C resulted in higher mechanical strengths and lower drying shrinkage, but the sharp decrease of workability and increase of autogenous shrinkage. At a constant W/C, the addition of UFA effectively …

Development Of The Uhpc Mix For 3d Printing, Buse Ilayda Oz

FIU Electronic Theses and Dissertations

This thesis utilizes the development of Ultra-High-Performance Concrete mix design for 3-Dimensional (3D) Printing purposes. 3D concrete printing offers many advantages such as the improvements in safety, quality, and productivity. Moreover, it holds a great advantage for the construction of structural elements that are difficult to construct by conventional methods. These advantages carry a huge potential for solving the aforementioned challenges.

Seven UHPC mixes have been designed and analyzed using various test setups for comparison purposes. Extrudability, flowability, buildability, and open time were measured using the fresh properties of the UHPC mixes. Mechanical properties were measured using compression test setups. …