Engineering Commons^™

Utilizing Waste Latex Paint Toward Improving The Performance Of Concrete, Mohamed Leithy, Eslam Gomaa, Ahmed A. Gheni, Mohamed Elgawady

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this paper, incorporating the waste latex paint (WLP) into the conventional concrete as a partial replacement of sand to improve its durability was investigated. The fresh and hardened characterizations, in addition to the durability of concrete, were examined. The slump test was used to evaluate the fresh properties, while the hardened properties were evaluated through the volume of voids and absorption rate, in addition to the compressive, splitting tensile, and flexural strengths tests. The durability performance was evaluated by the surface resistivity, bulk electrical resistivity, as well as freeze and thaw resistance tests. The results showed a reduction in …

Development And Characterization Of Coal-Based Thermoplastic Composite Material For Sustainable Construction, Haibin Zhang, Wenyu Liao, Genda Chen, Hongyan Ma

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The exploitation of coal and the disposal of waste plastic present significant environmental and economic challenges that require sustainable and profitable solutions. In response, we propose a renewable construction composite material of coal-based thermoplastic composite (CTC) that can be made from low-grade coal and plastic waste. We developed and tested the hot-press fabrication method for this CTC, using coal with a maximum particle size of 4.75 mm and recycled high-density polyethylene (HDPE). The effects of the coal fraction (50–80 wt.%) on compressive properties, thermal properties, microstructure, and ecological and economic efficiencies of the CTC were investigated. Test results revealed that …

Anti-Washout Concrete: An Overview, Hao Lu, Xiao Sun, Hongyan Ma

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Anti-washout concrete (AWC) is a special cement-based material that can be directly employed in underwater environments without dispersion. It was developed around 50 years ago, and more than 150 journal articles and technical reports have been published. This paper provides a holistic review about the basic fresh-state and hardened-state properties of the AWC, such as water (washout) resistance, consistency, bleeding and segregation resistance, mechanical properties, and durability, as well as relevant testing methods. The discrepancies between AWC's characteristics and those of conventional concrete are clearly presented. The mixture compositions, supplementary cementitious materials (SCMs), and other conditions that affect AWC's performance …

Use Of Saturated Lightweight Sand To Improve The Mechanical And Microstructural Properties Of Uhpc With Fiber Alignment, Huanghuang Huang, Le Teng, Xiaojian Gao, Kamal Khayat, Fazhou Wang, Zhichao Liu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper studied the influence of pre-saturated lightweight sand (LWS) on the mechanical and microstructural properties of UHPC cast with steel fiber alignment. The changes in hydration kinetics, porosity, nano-mechanical, and mechanical properties were studied. The LWS was used at 0–50% replacement volumes of total sand. Predominant fiber alignment was favored through a flow-induced casting method during casting of flexural prisms. Experiment results showed that the 28-d autogenous shrinkage was decreased from 450 to 275 μm/m with the LWS content increasing from 0 to 50%. The addition of 20% LWS led to maximum increases of 15%, 15%, and 20% in …

Development And Characterization Of Magnesium Phosphate Cement Based Ultra-High Performance Concrete, Jihui Qin, Fumin Dai, Hongyan Ma, Xiaobing Dai, Zhen Li, Xingwen Jia, Jueshi Qian

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study aims at the development of magnesium phosphate cement-based ultra-high performance concrete (MPC-UHPC). To this end, MPC paste phase was designed by using high magnesia-to-phosphate (M/P, 3.5) and low water-to-cement (W/C, 0.10–0.16) mass ratios, and certain amounts of ultra-fine fly ash (UFA, 5%–15%). Fresh and hardened properties, and microstructure of the developed MPC-UHPC were evaluated, and compared with those of conventional UHPC as well. Test results showed that lower W/C resulted in higher mechanical strengths and lower drying shrinkage, but the sharp decrease of workability and increase of autogenous shrinkage. At a constant W/C, the addition of UFA effectively …

Development Of The Uhpc Mix For 3d Printing, Buse Ilayda Oz

FIU Electronic Theses and Dissertations

This thesis utilizes the development of Ultra-High-Performance Concrete mix design for 3-Dimensional (3D) Printing purposes. 3D concrete printing offers many advantages such as the improvements in safety, quality, and productivity. Moreover, it holds a great advantage for the construction of structural elements that are difficult to construct by conventional methods. These advantages carry a huge potential for solving the aforementioned challenges.

Seven UHPC mixes have been designed and analyzed using various test setups for comparison purposes. Extrudability, flowability, buildability, and open time were measured using the fresh properties of the UHPC mixes. Mechanical properties were measured using compression test setups. …

Enhancement Of Asphalt Performance By Graphene-Based Bitumen Nanocomposites, Sara Moghtadernejad, Ehsan Barjasteh, Ren Nagata, Haia Malabeh

Mineta Transportation Institute Publications

As the State of California continues to grow, demand for enhanced infrastructure such as roadways and highways escalates. In view of the current average highway lifespan of 15–20 years, the improvement of asphalt binders leads to material sustainability by decreasing required maintenance and increasing the lifespan of roadways. In the present investigation, enhancement of asphalt binder properties was achieved by different methods of mixing varying compositions of graphene nanoparticles with an SBS polymer and asphalt binder. Additionally, experimental evaluation and comparison of the rheological and mechanical properties of each specimen is presented. Graphene nanoparticles have attracted great curiosity in the …

Integrated Mixing Machine For Sulfur Concrete Production, Maisa El Gamal, Khaled El-Sawy, Abdel-Mohsen O. Mohamed

All Works

The production of sulfur concrete (SC) from its ingredient materials requires controlled heating and mixing conditions at a temperature level of 130°-150 °C. Although this process considered to be common and applicable at the industrial level, it is difficult at the laboratory/research level. This paper presents the design and manufacturing details of a relatively inexpensive laboratory machine for heating and mixing sulfur concrete. The different components of the machine are described in detail to help researchers to produce high-quality sulfur concrete. In this work, the quality of the machine is verified through experimental testing of the physical and mechanical properties …

Design And Performance Of Polyurethane Elastomers Composed With Different Soft Segments, Xin Jin, Naisheng Guo, Zhanping You, Yiqiu Tan

Michigan Tech Publications

Thermoplastic polyurethane elastomers (TPUs) are widely used in a variety of applications as a result of flexible and superior performance. However, few scholars pay close attention on the design and synthesis of TPUs through the self‐determined laboratory process, especially on definite of chemical structures and upon the influence on properties. To investigate the properties of synthesized modifier based on chemical structure, firstly each kind of unknown structure and composition ratio of TPUs was determined by using a new method. Furthermore, the thermal characteristics and mechanical properties of modifiers were exposed by thermal characteristics and mechanics performance tests. The experimental results …

Determination Of Steels In Kentucky Bridges, Theodore Hopwood Ii, Christopher Goff, Sudhir Palle

Kentucky Transportation Center Research Report

The Kentucky Transportation Cabinet (KYTC) maintains over two hundred steel bridges constructed with types of steel which are unknown. Kentucky Transportation Center (KTC) researchers have developed a procedure for determining steel tensile properties (0.2% yield strength and ultimate tensile strength) which can be used to help identify unknown steels. The procedure involves extracting small coupons from the lower flanges of steel deck girder bridges. Coupons are then machined into sub-sized tensile testing specimens and suitable shapes for chemical analyses. Sub-sized tensile tests returned values generally comparable to those provided in mill certifications of steels purchased for laboratory trials. Several analytical …

The Effect Of Fine And Coarse Recycled Aggregates On Fresh And Mechanical Properties Of Self-Compacting Concrete, Mahmoud Nili, Hossein Sasanipour, Farhad Aslani

Research outputs 2014 to 2021

Today, the use of recycled aggregates as a substitute for a part of the natural aggregates in concrete production is increasing. This approach is essential because the resources for natural aggregates are decreasing in the world. In the present study, the effects of recycled concrete aggregates as a partial replacement for fine (by 50%) and coarse aggregates (by 100%) were examined in the self-compacting concrete mixtures which contain air-entraining agents and silica fumes. Two series of self-compacting concrete mixes have been prepared. In the first series, fine and coarse recycled mixtures respectively with 50% and 100% replacement with air entraining …

Development Of Heavyweight Self-Compacting Concrete And Ambient-Cured Heavyweight Geopolymer Concrete Using Magnetite Aggregates, Afsaneh Valizadeh, Farhad Aslani, Zohaib Asif, Matt Roso

Research outputs 2014 to 2021

Heavyweight self-compacting concrete (HWSCC) and heavyweight geopolymer concrete (HWGC) are new types of concrete that integrate the advantages of heavyweight concrete (HWC) with self-compacting concrete (SCC) and geopolymer concrete (GC), respectively. The replacement of natural coarse aggregates with magnetite aggregates in control SCC and control GC at volume ratios of 50%, 75%, and 100% was considered in this study to obtain heavyweight concrete classifications, according to British standards, which provide proper protection from sources that emit harmful radiations in medical and nuclear industries and may also be used in many offshore structures. The main aim of this study is to …

Properties And Mechanisms Of Self-Sensing Carbon Nanofibers/Epoxy Composites For Structural Health Monitoring, Yanlei Wang, Yongshuai Wang, Baolin Wan, Baoguo Han, Gaochuang Cai, Zhizheng Li

Civil and Environmental Engineering Faculty Research and Publications

In this paper, carbon nanofibers (CNFs) with high aspect ratio were dispersed into epoxy matrix via mechanical stirring and ultrasonic treatment to fabricate self-sensing CNFs/epoxy composites. The mechanical, electrical and piezoresistive properties of the nanocomposites filled with different contents of CNFs were investigated. Based on the tunneling conduction and percolation conduction theories, the mechanisms of piezoresistive property of the nanocomposites were also explored. The experimental results show that adding CNFs can effectively enhance the compressive strengths and elastic moduli of the composites. The percolation threshold of the CNFs/epoxy composites is 0.186 vol% according to the modified General Effective Media Equation. …

Factorial Design Approach In Proportioning Prestressed Self-Compacting Concrete, Wu-Jian Long, Kamal Khayat, Guillaume Lemieux, Feng Xing, Wei-Lun Wang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In order to model the effect of mixture parameters and material properties on the hardened properties of, prestressed self-compacting concrete (SCC), and also to investigate the extensions of the statistical models, a factorial design was employed to identify the relative significance of these primary parameters and their interactions in terms of the mechanical and visco-elastic properties of SCC. In addition to the 16 fractional factorial mixtures evaluated in the modeled region of -1 to +1, eight axial mixtures were prepared at extreme values of -2 and +2 with the other variables maintained at the central points. Four replicate central mixtures …

A Critical Review Of Research On Reuse Of Mechanically Recycled Frp Production And End-Of-Life Waste For Construction, Ardavan Yazdanbakhsh, Lawrence C. Bank

Publications and Research

For the last three decades, fiber reinforced polymer (FRP) composite materials have been widely used in major engineering industries. Managing FRP waste is becoming an important issue due to the growth in the production of FRP composite materials. In this article, the issue of FRP waste management is discussed and the commonly used methods for the handling of FRP waste are reviewed. One potentially viable use of FRP waste is in the partial replacement of fillers or aggregates in cementitious materials (particularly portland cement mortar and concrete). A number of important prior investigations performed on the use of FRP waste …

Thermophysical And Mechanical Properties Of Hardened Cement Paste With Microencapsulated Phase Change Materials For Energy Storage, Hongzhi Cui, Wenyu Liao, Shazim Ali Memon, Biqin Dong, Waiching Tang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this research, structural-functional integrated cement-based materials were prepared by employing cement paste and a microencapsulated phase change material (MPCM) manufactured using urea-formaldehyde resin as the shell and paraffin as the core material. The encapsulation ratio of the MPCM could reach up to 91.21 wt%. Thermal energy storage cement pastes (TESCPs) incorporated with different MPCM contents (5%, 10%, 15%, 20% and 25% by weight of cement) were developed, and their thermal and mechanical properties were studied. The results showed that the total energy storage capacity of the hardened cement specimens with MPCM increased by up to 3.9-times compared with that …