Engineering Commons^™

Rc Baja Independent Suspension And Chassis Design And Development, Joseph Fritz

All Undergraduate Projects

The goal of this project is to develop an RC car to compete in the MET RC Baja competition. A car will be constructed to be as lightweight, durable, and fast as possible while abiding by ROAR (Remotely Operated Auto Racers) regulations. As such, suspension, steering, chassis and drivetrain systems will need to be devised to form a complete vehicle. The chassis must provide mounting points for all other components of the vehicle and provide a rigid platform in order to create a stable vehicle. The suspension must operate smoothly, allowing for at least 1 inch of ground clearance, …

Rc Baja, Cam Jamison

All Undergraduate Projects

To satisfy the Mechanical Engineering Technology program requirements a senior project was accomplished with an RC car build. An RC car was designed, manufactured, and tested to meet all requirements set forth by American Society of Mechanical Engineers (ASME) RC Baja competition. A two-person team was assembled to build the RC Car. Teammate Paul Lervick was responsible for the suspension and chassis components and the other was responsible for the drivetrain and steering components. During the fall quarter drawings and general designs were created. Many different RC cars and motorized vehicles were referenced when initially coming up with aesthetic ideas. …

Jcati - Drive System, Tim Boswell

All Undergraduate Projects

Each year, Mechanical Engineering Technology students receive a grant from The Joint Center for Aerospace Technology Innovation (JCATI) to engineer a device that is capable of breaking down carbon fiber trimmings for recycling. The students who received the grant this year have redesigned portions of the existing system in an attempt to solve issues that have kept the system from working properly in the past. Though much collaboration between group members has been needed, each member has been responsible for their own portion of the project. The purpose of this portion of the project has been to address binding and …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Rc Baja, Ryder Satak

All Undergraduate Projects

American Society of Mechanical Engineers (ASME) hosts an RC Baja competition yearly at Central Washington University where schools from around the state gather to compete. The competition is based and scored from three different events: drag race, slalom, and a Baja course. Performing well in both the competition and other various tests will deem the car successful. The differential and drive train are two important features that allow the car to function properly. Using Solidworks 3D software and a 3D printer, the engineers were able to design functional components. The differential is designed to allow the rear wheels to spin …

Thermal Conductivity Measuring Device, Kyle Saalfeld

All Undergraduate Projects

The thermal conductivity measuring device is used to measure thermal conductivity of solids, liquids, and food products. Thermal conductivity is a material property that determines the rate at which heat disperses through a material. This determines how well insulation works, what materials are used as heat sinks, refrigeration, and how thoroughly food is cooked. The device measures thermal conductivity by heating up a thermistor bead using a high magnitude current for a measured duration and allowing the given heat to disperse; meeting the goal of designing a device that can easily measure the conductivity. Additional requirements of this device include …

Jcati Composite Delaminator, Payden Coffman

All Undergraduate Projects

Improvements need to be made to the existing delaminator system designed to crush proprietary Boeing 777 composite material. The current design incorporates a hydraulic system to achieve the high loads needed to separate material layers. The new system will need to be able to apply the same loads while at the same time allowing for a constant feed of material through the system. To achieve this, a “gear-like” crushing system will be implemented that will apply a high enough radial load into the material that will achieve delamination equal or greater than the previous design while at the same time …

Feed Control: Composite Recycle, Rosy Perez

All Undergraduate Projects

The Boeing Company gave Central Washington University an opportunity for students to research and come up with an idea to reduce costs and landfill waste caused by the trimmings from the 777x composite wing pieces. The engineering and manufacturing for this project is about transporting composite material through to the delamination and chipper process. The delamination process uses a ram to press two claw shaped devices together that bends and deforms the material in opposite directions. The chipper process uses counter rotating saw blades spaced 1/8” apart to produce small shredded material. It is important for this newly designed feed …

Stair Climbing Hand Truck, James Mcpherson

All Undergraduate Projects

Abstract

Getting a heavy object up a flight of stairs usually requires a team of two or more people. Even with a team of people, the task is often still difficult, dangerous, and possibly insurmountable by one person. This problem is especially prevalent in for those who are moving into apartment complexes. Most apartment complexes have many buildings with two or more floors of living quarters, and elevators are often missing. This project sought to offer a solution to this problem. The solution in question; a motorized hand-truck with 2, trigonal planar pinwheels in place of the stock wheels. The …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

R/C Mini Baja: Drivetrain, Kyle Aitken

All Undergraduate Projects

A device is needed that can power the back wheels of R/C car and allow it to drive smoothly. This drivetrain also has to transmit power to the axles in an acceptable height range to comply with the frame and suspension. The project was supported by a team member who designed the frame and suspension. The design of this project consists of two sub-assemblies that make up the drive train assembly. The transmission assembly uses gears to convert the rotational speed from the motor to the drive shaft. The gearbox assembly also uses gears and converts the rotational speed from …

Rc Baja Car Suspension, Tyler Martin

All Undergraduate Projects

This year the Mechanical Engineering Technology Department at CWU is holding an R/C Baja car competition using the same rules as the ASME competition. The designed car must compete in three separate events: the slalom course, drag race, and obstacle course. By not only completing, but also being competitive in each of the events, the car will be deemed a success. Suspension and steering are two essential components of any R/C car, and was the main focus for this report. The suspension must be able to support the car in the event of impacts. In addition, the steering must be …

Senior Project Hauff Tree Pruner, Brian Woolery

All Undergraduate Projects

Neil Hauff, a business owner and entrepreneur from the Yakima valley challenged a team of engineering students from Central Washington University to design a motorized apple tree pruner. This report will discuss the engineering and construction that went into creating the housing of the tree pruner. The housing component needed to be able to protect the moving parts of the pruner, while withstanding the rotational torque produced by the Makita power drill used to drive the pruner. The biggest constraint in designing the housing was to keep the weight of the housing component under 1.5 lbs, while still keeping the …

H.F. Hauff Pruner Cutting Blades, Wyley Stewart

All Undergraduate Projects

Apple orchards are a critical component of agriculture in the United States, and keeping the apple trees in the best shape for optimum growth and production is hard work. Neil Hauff, an agriculture industry expert, challenged students at CWU to engineer a power assisted tree pruner. Across the country, apple orchards need pruned every season. The pruning of the trees is strenuous manual labor that requires many man hours. The proposed solution is to create a power assisted tree pruner that would minimize the amount of work needed to trim each tree branch. This project has been separated into three …

High Accessibility Cabinet Insert, Matthew Leal

All Undergraduate Projects

Watching grandparents and parents get older, the struggle of day-to-day activities generally increases. One of the most recurring issues the older generation experiences nearly daily is their inability to reach dishes, glassware, and other things on the topmost shelves of a kitchen. Not only is it difficult for them to use things such as stepstools, it also becomes increasingly dangerous. With age, a fall from any height could be catastrophic. With this scenario in mind, a user-friendly cabinet insert would be a very effective way to combat this issue. However, many existing models of cabinet designed to fit these requirements …

Orchard Bin Atv Trailer, Neil F. Leitz

All Undergraduate Projects

A local orchardist was experiencing a problem that was being caused by their lack of apple picking bin moving equipment. The orchardist needed a well-engineered solution to this lack of equipment. The solution arrived at was a five bin trailer. There were multiple design requirements for this trailer, including the device needing to be able to interface with an ATV, be able to be loaded by hand, be able to carry five bins, and not exceed a budget of $750. While perfecting the design of the trailer, a number of different disciplines were utilized, which included dynamics, kinematics, static loading …

Asme Mini Rc Baja: Drivetrain, Jason M. Moore

All Undergraduate Projects

Title and author: ASME mini RC Baja Drivetrain by Jason Moore; partner Mike Cox. (Engineering Technologies, Safety, and Construction)

Abstract/Artists Statement: The issue that this project is concerned with is how to design and build a drivetrain, steering and suspension systems for an RC car. The systems must be simple and functional. Furthermore, these systems will be designed to fit on a small chassis and not interfere with each other. They also need to be strong and durable enough to propel the car forward and maneuver through various obstacles and be built in a way that is easy to take …

H.F. Hauff Pruner Housing & Ergonomics, Erich E. Heilman

All Undergraduate Projects

The technology of electric tree pruners in the current agricultural market has many engineering problems, including; a deficit in power output, excessive overheating, and ergonomics. The 3-man pruner team has coordinated with H.F. Hauff Co. Inc., an agricultural equipment company owned by Neil Hauff, to produce an electric pruner prototype which addresses these problems. The methods used to design the optimal pruner prototype includes traditional engineering stress analysis, force flow analysis, finite element software, and Solidworks modeling software. The construction of the pruner involved manual machining methods and C.N.C. (Computerized Numerical Control) mill technology. During the design process, the team …

Tabletop Die Cast System, Brad C. Barringer

All Undergraduate Projects

The project was to design, manufacture, and test a tabletop die cast system to be used as lab equipment in MET 257 – Casting Processes. The motivation for this project was the MET 257 – Casting Processes instructor’s desire to physically demonstrate the die casting process, but they were unable to find a system that would meet all of their requirements. They required a system design that was small, portable, would fit in the foundries limited space, had an open concept to allow students to see what was occurring during the pour, and compatibility with the foundries current equipment. The …

Multiple Apple Box Lift 1/10th Scale Model, Kyle J. Burlingame

All Undergraduate Projects

Title and Author: 1/10th Scale Multiple Apple Box Lift by Kyle Burlingame (Engineering Technologies, Safety, and Construction) Abstract/Artist statement: A 1/10th scale Multiple Apple Box Lift was designed and built as a proof of concept for a full scale device. The Multiple Apple Box Lift was designed to meet a customer’s requirements and to be presented at SOURCE. This device lifts the top half of the stacked apple boxes on a pallet in order to allow access to the boxes in the middle of the stack. The device can be manually operated by two people while in-between narrow rows of …

Truss Alignment Tool, Jason Hedin

All Undergraduate Projects

The purpose of this project is to follow the engineering process from start to finish, and create a fully functioning truss alignment tool that has been designed, constructed, and tested successfully. The first phase involves the design of the truss alignment tool. The main design requirements of the tool includes taking an input force of 60 pounds and outputting the 630 pounds of clamping force needed to realign a set of two stacked trusses and pull their bottom edges flush. The second phase involves the construction of the tool. This involves all machining processes associated with the cutting, shaping, and …