Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- Computational Fluid Dynamics (3)
- Tensile Strength (2)
- Wind Tunnel Tests (2)
- Ablation models (1)
- Additive Manufacturing (1)
-
- Aerodynamic Characteristics (1)
- Aircrafts (1)
- Alkaline Water Splitting (1)
- Ball Bearings (1)
- Ballistics Testing (1)
- Boundary Layer (1)
- CO2 damping (1)
- Carbon Fibers (1)
- Carbon Nanotubes (1)
- Closed Loop Systems (1)
- Computeraided Design (1)
- Degrees of Freedom(DOF) (1)
- Earth-Abundant Electrocatalysts (1)
- Electrochemistry (1)
- Electrolysis (1)
- Electromagnetic Interference (1)
- Failure Mode and Effect Analysis (1)
- Fixed Wing Aircraft (1)
- Fluid Dynamics (1)
- Fused Deposition Modeling (1)
- Gas Guns (1)
- Hydrogen Production (1)
- Hypersonic (1)
- Laminates (1)
- Laser confocal microscopy (1)
Articles 1 - 9 of 9
Full-Text Articles in Engineering
Effects Of Carbon-Based Ablation Products On Hypersonic Boundary Layer Stability, Olivia S. Elliott
Effects Of Carbon-Based Ablation Products On Hypersonic Boundary Layer Stability, Olivia S. Elliott
Theses and Dissertations
Hypersonic vehicles require an accurate prediction of the transition of the boundary layer for the design of the thermal protection system due to the high heating rates under turbulent flow. Many thermal protection systems are carbon-based and introduce new species, specifically CO2, into the boundary layer flow which are known to dampen the instabilities that lead to transition for hypersonic vehicles. A Computation Fluid Dynamics study was accomplished examining the concentration of CO2 required to impact boundary layer transition over both sharp and blunt cones. These results were used in conjunction with air-carbon ablation models models to …
On The Pulsed Laser Ablation Of Metals And Semiconductors, Todd A. Van Woerkom
On The Pulsed Laser Ablation Of Metals And Semiconductors, Todd A. Van Woerkom
Theses and Dissertations
This dissertation covers pulsed laser ablation of Al, Si, Ti, Ge, and InSb, with pulse durations from tens of picosecond to hundreds of microseconds, fluences from ones of J/cm2 to over 10,000 J/cm2, and in ambient air and vacuum. A set of non-dimensional scaling factors was created to interpret the data relative to the laser and material parameters, and it was found that pulse durations shorter than a critical timescale formed craters much larger than the thermal diffusion length, and longer pulse durations created holes much shallower than the thermal diffusion length. Low transverse order Gaussian beams …
Influence Of Leading Edge Oscillatory Blowing On Time-Accurate Dynamic Store Separation, Ryan G. Saunders
Influence Of Leading Edge Oscillatory Blowing On Time-Accurate Dynamic Store Separation, Ryan G. Saunders
Theses and Dissertations
The primary objective of this research is to support the static and dynamic characterization and the time-accurate dynamic load data acquisition of store separation from a cavity with leading edge oscillatory blowing. Developing an understanding of, and potentially controlling, pitch bifurcation of a store release is a motivation for this research. The apparatus and data acquisition system was used in a two-part experiment to collect both static and dynamic testing data in the AFIT low speed wind tunnel in speeds of 60, 100, and 120 mph, from Reynolds numbers varying from 5.5x104 to 4.6x105, depending on reference …
Tracking Shock Movement On The Surface Of An Oscillating, Straked Semispan Delta Wing, Justin A. Pung
Tracking Shock Movement On The Surface Of An Oscillating, Straked Semispan Delta Wing, Justin A. Pung
Theses and Dissertations
A recent research effort, sponsored by the Air Force Office of Scientific Research, numerically investigated the unsteady aerodynamic flow field around an oscillating, straked, delta wing. The study was centered on determining the importance of the unsteady aerodynamic forces acting as a driver for a nonlinear motion known as limit cycle oscillations. The current effort focused on creating a computational model to compare to the results of previous tests and modeling efforts and discover new information regarding the onset of LCO. The computational model was constructed using the Cartesian overset capabilities of the CREATE-AV™ fixed wing fluid dynamics solver Kestrel. …
Manufacture Of Fused Deposition Modeling Joints Using Ultem 9085, Zane A. Willburn
Manufacture Of Fused Deposition Modeling Joints Using Ultem 9085, Zane A. Willburn
Theses and Dissertations
The manufacture of joints between a base structure and a structure manufactured via Fused Deposition Modeling (FDM) will be investigated. ULTEM 9085, a high temperature plastic with potential aerospace applications, will be the material used. The specific application this research is focused on is a robotic and mobile FDM printer capable of building structures onto other structures in space. A joint will be formed by fusing the base layer of the printed structure and the top of the base structure together. Tensile testing will be performed to determine the strength of the bond between parts. Tensile specimens will be manufactured …
Analytical Models And Control Design Approaches For A 6 Dof Motion Test Apparatus, Kyra L. Schmidt
Analytical Models And Control Design Approaches For A 6 Dof Motion Test Apparatus, Kyra L. Schmidt
Theses and Dissertations
Wind tunnels play an indispensable role in the process of aircraft design, providing a test bed to produce valuable, accurate data that can be extrapolated to actual flight conditions. Historically, time-averaged data has made up the bulk of wind tunnel research, but modern flight design necessitates the use of dynamic wind tunnel testing to provide time-accurate data for high frequency motion. This research explores the use of a 6 degree of freedom (DOF) motion test apparatus (MTA) in the form of a robotic arm to allow models inside a subsonic wind tunnel to track prescribed trajectories to obtain time-accurate force …
Ballistic Evaluation Of Carbon Nanotube Sheet Material In Multifunctional Applications, Casey M. Keilbarth
Ballistic Evaluation Of Carbon Nanotube Sheet Material In Multifunctional Applications, Casey M. Keilbarth
Theses and Dissertations
Significant development of carbon nanotubes has occurred since they were first studied in the 1990's. Attempts to capture the phenomenal molecular properties in practical applications are gaining ground as new methods of producing CNTs have been developed. This thesis sought to determine if the addition of commercially produced CNT sheets to thin carbon fiber panels improved the ballistic properties of the panel. The difference between 0 and 4 CNT sheets was studied. The hypothesis was that inte- grating CNT sheets into the laminate would increase the projectile energy absorbed by the panel and reduce the damage to the panel incurred …
Computational Aerothermodynamic Analysis Of Satellite Trans-Atmospheric Skip Entry Survivability, John J. Runco
Computational Aerothermodynamic Analysis Of Satellite Trans-Atmospheric Skip Entry Survivability, John J. Runco
Theses and Dissertations
Computational aerothermodynamic analysis is presented for a spacecraft in low Earth orbit performing an atmospheric skip entry maneuver. Typically, atmospheric reentry is a terminal operation signaling mission end-of-life and, in some instances, executed for spacecraft disposal. A variation on reentry – skip entry – is an aeroassisted trans-atmospheric maneuver in which a spacecraft utilizes the effects of aerodynamic drag in order to reduce energy prior to a terminal entry, pinpoint a targeted entry, or change orbital elements such as inclination. Spacecraft performing a skip entry enable new modes of maneuver to enhance operations in nominal or possibly contested mission environments. …
Engineering Of Earth-Abundant Electrochemical Catalysts, Dylan D. Rodene
Engineering Of Earth-Abundant Electrochemical Catalysts, Dylan D. Rodene
Theses and Dissertations
Alternative energy research into hydrogen production via water electrolysis addresses environmental and sustainability concerns associated with fossil fuel use. Renewable-powered electrolyzers are foreseen to produce hydrogen if energy and cost requirements are achieved. Electrocatalysts reduce the energy requirements of operating electrolyzers by lowering the reaction kinetics at the electrodes. Platinum group metals (PGMs) tend to be utilized as electrocatalysts but are not readily available and are expensive. Ni1-xMox alloys, as low-cost and earth-abundant transition metal nanoparticles (NPs), are emerging as promising electrocatalyst candidates to replace expensive PGM catalysts in alkaline media. Pure-phase cubic and hexagonal Ni1-x …