Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 7 of 7
Full-Text Articles in Engineering
Open Source Waste Plastic Granulator, Arvind Ravindran, Sean Scsavnicki, Walker Nelson, Peter Gorecki, Jacob Franz, Shane Oberloier, Theresa K. Meyer, Andrew Barnard, Joshua M. Pearce
Open Source Waste Plastic Granulator, Arvind Ravindran, Sean Scsavnicki, Walker Nelson, Peter Gorecki, Jacob Franz, Shane Oberloier, Theresa K. Meyer, Andrew Barnard, Joshua M. Pearce
Michigan Tech Publications
In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built, and tested for its ability to convert post-consumer waste, 3D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404 W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than $2000 USD in materials. The experimentally measured power use …
Low-Cost Open Source Ultrasound-Sensing Based Navigational Support For The Visually Impaired, Aliaksei Petsiuk, Joshua M. Pearce
Low-Cost Open Source Ultrasound-Sensing Based Navigational Support For The Visually Impaired, Aliaksei Petsiuk, Joshua M. Pearce
Michigan Tech Publications
Nineteen million Americans have significant vision loss. Over 70% of these are not employed full-time, and more than a quarter live below the poverty line. Globally, there are 36 million blind people, but less than half use white canes or more costly commercial sensory substitutions. The quality of life for visually impaired people is hampered by the resultant lack of independence. To help alleviate these challenges this study reports on the development of a low-cost, open-source ultrasound-based navigational support system in the form of a wearable bracelet to allow people with the lost vision to navigate, orient themselves in their …
Spontaneous Selective Deposition Of Iron Oxide Nanoparticles On Graphite As Model Catalysts, Chathura De Alwis, Timothy Leftwich, Pinaki Mukherjee, Alex Denofre, Kahryn Perrine
Spontaneous Selective Deposition Of Iron Oxide Nanoparticles On Graphite As Model Catalysts, Chathura De Alwis, Timothy Leftwich, Pinaki Mukherjee, Alex Denofre, Kahryn Perrine
Michigan Tech Publications
Iron oxide nanomaterials participate in redox processes that give them ideal properties for their use as earth-abundant catalysts. Fabricating nanocatalysts for such applications requires detailed knowledge of the deposition and growth. We report the spontaneous deposition of iron oxide nanoparticles on HOPG in defect areas and on step edges from a metal precursor solution. To study the nucleation and growth of iron oxide nanoparticles, tailored defects were created on the surface of HOPG using various ion sources that serve as the target sites for iron oxide nucleation. After solution deposition and annealing, the iron oxide nanoparticles were found to nucleate …
Mechanical Properties And Applications Of Recycled Polycarbonate Particle Material Extrusion-Based Additive Manufacturing, Matthew J. Reich, Aubrey Woern, Nagendra Gautam Tanikella, Joshua M. Pearce
Mechanical Properties And Applications Of Recycled Polycarbonate Particle Material Extrusion-Based Additive Manufacturing, Matthew J. Reich, Aubrey Woern, Nagendra Gautam Tanikella, Joshua M. Pearce
Michigan Tech Publications
Past work has shown that particle material extrusion (fused particle fabrication (FPF)/fused granular fabrication (FGF)) has the potential for increasing the use of recycled polymers in 3D printing. This study extends this potential to high-performance (high-mechanical-strength and heat-resistant) polymers using polycarbonate (PC). Recycled PC regrind of approximately 25 mm2 was 3D printed with an open-source Gigabot X and analyzed. A temperature and nozzle velocity matrix was used to find useful printing parameters, and a print test was used to maximize the output for a two-temperature stage extruder for PC. ASTM type 4 tensile test geometries as well as ASTM-approved …
Systems Analysis For Pet And Olefin Polymers In A Circular Economy, David R. Shonnard, Emily Tipaldo, Vicki Thompson, Joshua M. Pearce, Gerard T. Caneba, Robert Handler
Systems Analysis For Pet And Olefin Polymers In A Circular Economy, David R. Shonnard, Emily Tipaldo, Vicki Thompson, Joshua M. Pearce, Gerard T. Caneba, Robert Handler
Michigan Tech Publications
Polyethylene terephthalate (PET #1) and polyolefin plastics such polyethylene (HDPE #2, LDPE #4) and polypropylene (PP #5) are major products from the chemical industry, and they comprise a significant fraction of municipal solid waste that ends up in landfills or as litter and marine debris. The reuse of these polymeric materials can be optimized through systems analysis with a view on materials flow analysis, techno-economics, environmental life cycle assessment, and consequential societal impacts. This contribution will present the overall research approach for this exploratory project within the DOE- and industry-funded REMADE Institute and end with a proposed systems analysis framework.
Open Source Completely 3-D Printable Centrifuge, Salil S. Sule, Aliaksei Petsiuk, Joshua M. Pearce
Open Source Completely 3-D Printable Centrifuge, Salil S. Sule, Aliaksei Petsiuk, Joshua M. Pearce
Michigan Tech Publications
Centrifuges are commonly required devices in medical diagnostics facilities as well as scientific laboratories. Although there are commercial and open source centrifuges, the costs of the former and the required electricity to operate the latter limit accessibility in resource-constrained settings. There is a need for low-cost, human-powered, verified, and reliable lab-scale centrifuges. This study provides the designs for a low-cost 100% 3-D printed centrifuge, which can be fabricated on any low-cost RepRap-class (self-replicating rapid prototyper) fused filament fabrication (FFF)- or fused particle fabrication (FPF)-based 3-D printer. In addition, validation procedures are provided using a web camera and free and open …
Preliminary Automated Determination Of Edibility Of Alternative Foods: Non-Targeted Screening For Toxins In Red Maple Leaf Concentrate, Joshua M. Pearce, Maryam Khaksari, David C. Denkenberger
Preliminary Automated Determination Of Edibility Of Alternative Foods: Non-Targeted Screening For Toxins In Red Maple Leaf Concentrate, Joshua M. Pearce, Maryam Khaksari, David C. Denkenberger
Michigan Tech Publications
Alternative food supplies could maintain humanity despite sun-blocking global catastrophic risks (GCRs) that eliminate conventional agriculture. A promising alternative food is making leaf concentrate. However, the edibility of tree leaves is largely uncertain. To overcome this challenge, this study provides the methods for obtaining rapid toxics screening of common leaf concentrates. The investigation begins with a non-targeted approach using an ultra-high-resolution hybrid ion trap orbitrap mass spectrometer with electrospray ionization (ESI) coupled to an ultra-high pressure two-dimensional liquid chromatograph system on the most common North American leaf: the red maple. Identified chemicals from this non-targeted approach are then cross-referenced with …