Engineering Commons^™

Portable Electrochemical System For Flexible Hybrid Electronics, Anthony Joseph Hanson

Masters Theses

This work focuses on the fabrication and design of a portable electrochemical sensing system for flexible hybrid electronic (FHE) sensors. A three-electrode chemical sensor was fabricated using copper tape on polyethylene terephthalate (PET) substrate, using laser etching process. An electronic circuit was designed to measure the sensor response through electrochemical techniques to detect different concentrations of glucose. The device was calibrated to give the user a concentration value in 5 seconds. The system was also designed to preform tests such as cyclic voltammogram and chronoamperogram for various chemicals. A Bluetooth Low Energy module was used to wirelessly transmit the results …

Embedded System Design Of Robot Control Architectures For Unmanned Agricultural Ground Vehicles, Ryan Humphrey

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Engineering technology has matured to the extent where accompanying methods for unmanned field management is now becoming a technologically achievable and economically viable solution to agricultural tasks that have been traditionally performed by humans or human operated machines. Additionally, the rapidly increasing world population and the daunting burden it places on farmers in regards to the food production and crop yield demands, only makes such advancements in the agriculture industry all the more imperative. Consequently, the sector is beginning to observe a noticeable shift, where there exist a number of scalable infrastructural changes that are in the process of slowly …

Analysis And Tests For A Hybrid Model Created From Classical Taguchi And Goal Post Manufacturing Loss Models, Prajwal Bhandari

Electrical Engineering Theses

We present an analysis of the previously proposed “modified quadratic” loss function. This loss model integrates elements from both Classical Taguchi and Goal Post manufacturing loss models. Specifically, the analyzed hybrid model follows the Taguchi loss quadratic dependence between the upper and lower manufacturing specification limits. On the other hand, outside of these limits, the loss rule is in agreement with the Goal Post Model. Supported by the results of analysis contained herein the Taguchi-Hybrid model does not overestimate the loss as is inherent to the classical Taguchi model. Also, the proposed Taguchi Hybrid model does not ignore deviations from …

Laboratory Manual For Engineering Electronics, Sandip Das, Walter Thain, Sheila Hill

Engineering Open Textbooks

The primary objective of this project was to improve the laboratory manuals and associated ancillary learning resources for the junior-level course, Engineering Electronics (EE3401), which is a required course for students in three different degree programs at Kennesaw State University – Electrical Engineering, Mechatronics Engineering, and Computer Engineering.

In this project, we have developed and transformed the previous lab manuals, as well as added new learning materials. We have included detailed technical instructions within the lab manuals, revised the contents for improved readability, implemented coherent formatting across all manuals, introduced interactive links as necessary, developed and integrated pre-lab exercises, created …

Improving 3d Printed Prosthetics With Sensors And Motors, Rachel Zarin

Honors Projects

A 3D printed hand and arm prosthetic was created from the idea of adding bionic elements while keeping the cost low. It was designed based on existing models, desired functions, and materials available. A tilt sensor keeps the hand level, two motors move the wrist in two different directions, a limit switch signals the fingers to open and close, and another motor helps open and close the fingers. All sensors and motors were built on a circuit board, programmed using an Arduino, and powered by a battery. Other supporting materials include metal brackets, screws, guitar strings, elastic bands, small clamps, …

Dc To Dc Usb-C Charger, Nikki Gmerek, Kenneth Nguyen, Uriel Serna

Electrical Engineering

The DC House USB-C Charger will convert the 48V input from the DC house, found on the Cal Poly campus, to 3 USB-C outputs: 5V, 12V, and 24 volts. The converter will deliver a total of 185 Watts out across all 3 outputs, with an efficiency greater than 82% at full load. The USB-C ports will be used to connect to compatible phones, laptops or any other device for charging/powering purposes. The goal of this project is to develop the most efficient and safe converter to deliver power to multiple outputs using USB-C, for items as small as a cell …

A Swimming Open-Water Navigation Assistive Headset And Receiver, Zakk B. Rhodes

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Open water swimming is a common activity dating back to ancient times. One challenge with open water swimming is navigation because while maintaining proper swimming technique suggests the head be in the water, it is difficult to see where one is going. Thus swimmers must bring their head out of the water periodically to sight landmarks. This work describes a solution to this problem by a design for a GPS device to assist swimmers with navigation. The swimmer can plan their own route, send it to the device, and then be guided by the device. They then will not have …