Engineering Commons^™

Fundamentals Of Aerospace Engineering, Manny Pacquiao

Manny Pacquiao

Flight Vehicle Design, Andrew Ning

Books

No abstract provided.

Ultraviolet Imager Application For A Cube Satellite, Jason Grillo, Troy Hajjar, Brady Hill

Mechanical Engineering

This document serves as the final design review (FDR) report for the 2018 Cal Poly CubeSat Ultraviolet Imager senior project, sponsored by UC Berkeley Space Sciences Laboratories (SSL). SSL wants to monitor the ionosphere above Earth to gain a better understanding of its properties and particle interactions. Far Ultraviolet (FUV) imaging is a good way to obtain high quality images of the ionosphere and the Earth's auroras, and advancement in optic technologies have made cube satellites (CubeSats) an ideal vessel for a FUV imager, as they are relatively low-cost, lightweight, and can be repeatedly deployed. These CubeSat FUV imagers could …

Assessment And Comparison Of Aviation Manufacturing Industries Throughout Mexico And Brazil, Omar E. Morsi, Kelly A. Whealan-George, Aaron D. Clevenger

Aaron D. Clevenger

This literature review serves to provide insight and understanding in regards to the evolving aviation manufacturing industry throughout the globe and more specifically, Mexico and Brazil. Increased demand for aircraft units both in the commercial and private sectors have led to unprecedented expansions in aircraft manufacturing across the industry. In order to illuminate certain potentials and current growth levels of such industries, this review will delve into an array of information and specifications in regards to economic, political, and cultural influences throughout both Mexican and Brazilian markets respectively. In conclusion, the review will identify the transformation of an aviation manufacturing …

Aviation Cybersecurity: An Overview, Gary C. Kessler, J. Philip Craiger

National Training Aircraft Symposium (NTAS)

Information security—aka cybersecurity—is the most rapidly growing threat to critical infrastructures, including the aviation industry. Due to the plethora of digital devices, ubiquity of the Internet and other networks, and the rapid growth in the adoption of technology, everyone is an information system security manager. Every professional in the aviation and aeronautics industry use computers, mobile devices, tablets, GPS devices, and/or other hardware on a daily basis, as well as go online for a variety of reasons.

Attacks on information have been ongoing since the inception of the industry a hundred years ago, in such forms as intellectual property theft …

Development Of Low Cost, Environmentally Friendly And High Strength Carbon Foams From Bread And Cake, Laura Mountain-Tuller

Materials Engineering

Carbon foam is a high niche material that consists of a highly porous, three-dimensional cellular network that is characterized by extremely high strength-to-weight ratios and low thermal conductivity. Due to these properties, carbon foams excel in structural and thermal applications, especially in the aerospace industry. Typically, carbon foams are formed through a heating process called pyrolysis of polymer precursors with high carbon content. This process is done at high temperatures in an oxygen free environment. These precursors are expensive to make and use toxic chemicals to produce, therefore, there is a push to find an environmentally friendly and cost-effective method …

Thermal Modelling And Validation Of Heat Profiles In An Rf Plasma Micro-Thruster, Alec Sean Henken

Master's Theses

The need and demand for propulsion devices on nanosatellites has grown over the last decade due to interest in expanding nanosatellite mission abilities, such as attitude control, station-keeping, and collision avoidance. One potential micro-propulsion device suitable for nanosatellites is an electrothermal plasma thruster called Pocket Rocket. Pocket Rocket is a low-power, low-cost propulsion platform specifically designed for use in nanosatellites such as CubeSats. Due to difficulties associated with integrating propulsion devices onto spacecraft such as volume constraints and heat dissipation limitations, a characterization of the heat generation and heat transfer properties of Pocket Rocket is necessary. Several heat-transfer models of …

Upgrading The Sr-30 Miniature Turbojet For Adaptable Exhaust, Shannon Ferreira, Erin Mcmurchie, Peter Pratt

Mechanical Engineering

The California Polytechnic State University, San Luis Obispo (Cal Poly, SLO) Aerospace Department is requesting a variable nozzle adaptation for their SR-30 turbojet engine. The nozzle is intended for laboratory use in sophomore and junior level courses to supplement instruction on the effects that exhaust behavior has on the performance of propulsion technologies. Topics covered during a performance study of the SR-30 turbojet engine will include, but are not limited to: Brayton Cycle analysis, turbojet operation in ideal and non-ideal test conditions, instrumentation limitations, and basic nozzle operation. The SR-30 turbojet engine is similar in design and operation to engines …

Reducing Flagging And Fraying In Composite Sandwich Panel Machining, Stefan Kutz, Georgia Donaldson

Scholars Week

This is a collaboration of Western faculty, students, and Zodiac Aerospace Cabin Interiors in the investigation of refining one of the company's key manufacturing processes. This problem was analyzed with the use of high speed videography to view the cutting mechanics from a new perspective. The team discovered a variety of machining strategies for the company to implement and improve the efficiency of their production in the work towards eliminating secondary processes.

The Next Step Beyond Identifying Field Variability: Integrating Unmanned Aerial Systems Into The Farm Management Workflow, Kevin A. Adkins, Christen C. Bailey, Aspen E. Taylor

Kevin A. Adkins, PhD

Assessment And Comparison Of Aviation Manufacturing Industries Throughout Mexico And Brazil, Omar E. Morsi, Kelly A. Whealan-George, Aaron D. Clevenger

International Journal of Aviation, Aeronautics, and Aerospace

This literature review serves to provide insight and understanding in regards to the evolving aviation manufacturing industry throughout the globe and more specifically, Mexico and Brazil. Increased demand for aircraft units both in the commercial and private sectors have led to unprecedented expansions in aircraft manufacturing across the industry. In order to illuminate certain potentials and current growth levels of such industries, this review will delve into an array of information and specifications in regards to economic, political, and cultural influences throughout both Mexican and Brazilian markets respectively. In conclusion, the review will identify the transformation of an aviation manufacturing …

Design Of Shape-Conforming Nosecone For Optimal Fluid Flow From Transonic To Supersonic Range, Anna Tombazzi

Williams Honors College, Honors Research Projects

Modern flight vehicles, such as rockets, missiles, and airplanes, experience a force caused by forebody wave drag during the flight. This drag force is induced when the frontal point of each vehicle breaks the pressure wave during flight. Efforts to reduce this wave drag force to improve flight efficiency include modifying the nosecone profile of the flight vehicles to lower the drag force.

This project revolved around creating a design to make the transformation of nosecone shapes from a ¾ Parabolic profile to a ½ Power Series profile possible, mid-flight. Using a novel nosecone assembly, shape memory alloys (SMAs) and …

Environmentally Friendly Alternates To Chemlok 233 Adhesive Cement, Madeline M. Busch

Williams Honors College, Honors Research Projects

The purpose of this project was to determine and qualify suitable, environmentally friendly replacement(s) for the current Chemlok 233 adhesive cement used by UTC Aerospace. Chemlok 233 was discontinued by the manufacturer based on the availability of a hazardous solvent (Trichloroethylene – TCE). The Chemlok 233 Control and four Experimental alternates with similar properties were lab tested for adhesion strength in various UTC proprietary cement specifications. The specifications modeled Chemlok’s uses in the construction of pneumatic de-icers. Chemlok 2332 was selected for use in Cement A, and Chemlok 402 was chosen for use in Cement B based on their highest …