Engineering Commons^™

Evaluation Of Deformable Posts In The Zoi And Rigid Posts In Stiff Soil, Thomas Ammon

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Debris fences are commonly used by states, in conjunction with a concrete parapet, to protect railway tracks. Their use limits the intrusion of debris that could damage tracks or clutter rail lines. Due to a lack of previously crash-tested systems, the safety performance of such designs are largely unknown. The Iowa Department of Transportation (DOT) desired that researchers at the Midwest Roadside Safety Facility (MwRSF) design a crashworthy debris fence mounted on top of a concrete parapet to meet the Manual for Assessing Safety Hardware (MASH) TL-3 crash test conditions. Part 1 of this thesis details the literature review and …

Drop Generation Using Cross-Flow In Rigid Body Rotation, Haipeng Zhang

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Inspired by crossflow membrane droplet generation and microfluidic droplet generation, I propose an easy method to generate monodisperse drops using cross-flow caused by rigid body rotation. In this approach, a dispersed phase (DP) liquid was injected through a stationary vertical needle into an immiscible continuous phase (CP) liquid which was in rigid body rotation. A DP drop growing at the end of the needle experienced fluid dynamic forces from the horizontal CP flow, and it was detached from the needle when it had grown to a certain size. This study investigated the relationship between the resultant size of drops and …

System And Methods For Ventilation Through A Body Cavity, Mark A. Borden, Benjamin S. Terry

Department of Mechanical and Materials Engineering: Faculty Publications

A system and methods for the delivery of oxygen through a body cavity of a subject using oxygen microbubbles . Through circulation of oxygen microbubbles through the body cavity , oxygen and carbon dioxide exchange may occur . Overall improvement in extending survival rate time during emergency situations caused by pulmonary or similar oxygen - intake restricting injury and / or failure may be achieved through use of the invented system and methods .

Hemodynamics And Pathology Of An Enlarging Abdominal Aortic Aneurysm Model In Rabbits, Hongmei Chen, Yonghua Bi, Siyeong Yu, Linxia Gu, Xiaoyan Zhu, Xinwei Han

Department of Mechanical and Materials Engineering: Faculty Publications

Hemodynamics may play an essential role in the initiation and progression of abdominal aortic aneurysm (AAA). We aimed to study the mechanism of self-healing process by the changes of hemodynamics and pathology in an enlarging AAA in rabbits. Seventy-two rabbits were randomly divided into three groups. Rabbits underwent extrinsic coarctation and received a 10-minute elastase incubation in Group A and Group B. Absorbable suture used in Group A was terminated by balloon dilation at week 4. Diameter was measured after 1, 3, 5, and 15 weeks, computational fluid dynamics analysis was performed at week 3 and week 15. Rabbits were …

Techniques To Stimulate And Interrogate Cell–Cell Adhesion Mechanics, Ruiguo Yang, Joshua A. Broussard, Kathleen J. Green, Horacio D. Espinosa

Department of Mechanical and Materials Engineering: Faculty Publications

Cell–cell adhesions maintain the mechanical integrity of multicellular tissues and have recently been found to act as mechanotransducers, translating mechanical cues into biochemical signals. Mechanotransduction studies have primarily focused on focal adhesions, sites of cell-substrate attachment. These studies leverage technical advances in devices and systems interfacing with living cells through cell–extracellular matrix adhesions. As reports of aberrant signal transduction originating from mutations in cell–cell adhesion molecules are being increasingly associated with disease states, growing attention is being paid to this intercellular signaling hub. Along with this renewed focus, new requirements arise for the interrogation and stimulation of cell–cell adhesive junctions. …

Study Of The Femtosecond Laser Processed Surfaces, Imprinting, And Casting For Changing The Wettability Of Surfaces, Yingxiao Song

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Femtosecond Laser Surface Processing (FLSP) is a technology to fabricate micro/nano surface structures. These patterned surface structures show great importance in many applications, especially in controlling the wettability of the surface. Imprinting is a typical method for manufacturing large volumes of surfaces. This study combines two processes (FLSP and stamping) together to produce a surface structure similar to the original FLSP surface. In the first step, micro/nano structured surface mounds were fabricated by femtosecond laser processing. Then, these FLSP surfaces served as molds for subsequent imprinting to replicated the “negative” surface on a blank material. Surface morphology and peak-to-valley roughness …

Strong And Tough Continuous Nanofibers, Yuris Dzenis

Department of Mechanical and Materials Engineering: Faculty Publications

Amethod of fabricating a continuous nanofiber is described . The method includes preparing a solution of one or more polymers and one or more solvents and electrospinning the solution by discharging the solution through one or more liquid jets into an electric field to yield one or more continuous nanofibers . The electrospinning process ( i ) highly orients one or more polymer chains in the one or more continuous nanofibers along a fiber axis of the one or more continuous nanofibers , and ( ii ) suppresses polymer crystallization in the one or more continuous nanofibers . The one …

Development Of Iowa Dot Combination Bridge Separation Barrier With Bicycle Railing, Chaz M. Ginger

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The Iowa Department of Transportation typically builds separation barriers between vehicle and pedestrian/bicycle facilities when sidewalks or trails are present on vehicular bridges. Currently, Iowa DOT employs a combination bridge rail that utilizes a concrete parapet that previously had been successfully evaluated to National Cooperative Highway Research Program (NCHRP) Report 350 Test Level 4 (TL-4) criteria for these situations. While the parapet had been successfully evaluated, the combination bridge rail system as a whole had not been evaluated to any crash test standards. Iowa DOT desired that researchers at Midwest Roadside Safety Facility (MwRSF) design and test a combination bridge …

Design Of Parallel Robot For Dental Articulation And Its Optimization, Abulimiti Delimulati

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A dental articulator is a mechanical device used to simulate the relative position and motion between the upper and lower jaw when constructing and testing dental prostheses. Typically, it can be adjusted to approximate patient-specific jaw kinematics in order to analogue the static relationship and specific motions of a patient’s mandible to maxilla. However, the use of dental articulators is essentially a trial-and-error method in order to fine-tune fit and function of a dental prosthesis. Some of the most advanced current dental articulators can reproduce the position and the motion passively; furthermore, dentists need special training for measuring patients’ maxillofacial …

Near-Field Heat Transfer Enabled Nanothermomechanical Memory And Logic Devices, Sidy Ndao, Mahmoud Elzouka

Department of Mechanical and Materials Engineering: Faculty Publications

A thermomechanical memory / logic device is disclosed . In embodiments , the thermomechanical device includes a first thermally controlled terminal ( e . g . , hot terminal ) ; a second thermally controlled terminal ( e . g . , cool terminal / base ) ; a stem or other structure that can be thermally expanded connected to the cool terminal ; and a thermal conductive head coupled to the stem . The head can exchange heat with the hot terminal . The stem and head are between the first thermally controlled terminal and the second thermally controlled …

Smart Bandage For Monitoring And Treatment Of Chronic Wounds, Pooria Mostafalu, Ali Tamayol, Rahim Rahimi, Manuel Ochoa, Akbar Khalilpour, Gita Kiaee, Iman K. Yazdi, Sara Bagherifard, Mehmet R. Dokmeci, Babak Ziaie, Sameer R. Sonkusale, Ali Khademhosseini

Department of Mechanical and Materials Engineering: Faculty Publications

Chronic wounds are a major health concern and they affect the lives of more than 25 million people in the United States. They are susceptible to infection and are the leading cause of nontraumatic limb amputations worldwide. The wound environment is dynamic, but their healing rate can be enhanced by administration of therapies at the right time. This approach requires real-time monitoring of the wound environment with on-demand drug delivery in a closed-loop manner. In this paper, a smart and automated flexible wound dressing with temperature and pH sensors integrated onto flexible bandages that monitor wound status in real-time to …

Prevascularization Of 3d Printed Bone Scaffolds By Bioactive Hydrogels And Cell Co-Culture, Mitchell Kuss, Shaohua Wu, Ying Wang, Jason B. Untrauer, Wenlong Li, Jung Yul Lim, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

Vascularization is a fundamental prerequisite for large bone construct development and remains one of the main challenges of bone tissue engineering. Our current study presents the combination of 3D printing technique with a hydrogel-based prevascularization strategy to generate prevascularized bone constructs. Human adipose derived mesenchymal stem cells (ADMSC) and human umbilical vein endothelial cells (HUVEC) were encapsulated within our bioactive hydrogels, and the effects of culture conditions on in vitro vascularization were determined. We further generated composite constructs by forming 3D printed polycaprolactone/hydroxyapatite scaffolds coated with cell-laden hydrogels and determined how the co-culture affected vascularization and osteogenesis. It was demonstrated …

Interface Structure And Deformation Mechanisms Of Mg/Nb Multilayers, Xinyan Xie

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Magnesium (Mg) and its alloys, as the lightest structural materials, are very attractive for a range of weight sensitive applications, such as aircraft engine, transportation industry and so on. However, their further applications are limited due to the weak properties, such as the low strength and poor ductility. In recent years, advanced techniques aiming at the modification of the microstructures, have been developed to promote the properties of Mg and its alloys, such as modifying the texture, refining the grain size, forming the intermetallic phase, and introducing the interfaces or stacking faults into the systems. Constructing Mg/Nb multilayers, which introduces …

Migration Resistance Of Esophageal Stents: The Role Of Stent Design, Hozhabr Mozafari, Pengfei Dong, Shijia Zhao, Yonghua Bi, Xinwei Han, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Objective: Stenting is one of the major treatments for malignant esophageal cancer. However, stent migration compromises clinical outcomes. A flared end design of the stent diminishes its migration. The goal of this work is to quantitatively characterize stent migration to develop new strategies for better clinical outcomes.

Methods: An esophageal stent with flared ends and a straight counterpart were virtually deployed in an esophagus with asymmetric stricture using the finite element method. The resulted esophagus shape, wall stress, and migration resistance force of the stent were quantified and compared.

Results: The lumen gain for both the flared stent and the …

System And Method For Controlling Operations Of Air - Conditioning System, Mouhacine Benosman, Petros Boufounos, Boris Kramer, Piyush Grover

Department of Mechanical and Materials Engineering: Faculty Publications

A method controls an operation of an air - conditioning system generating airflow in a conditioned environment . The method updates a model of airflow dynamics connecting values of flow and temperature of air conditioned during the operation of the air - conditioning system . The model is updated interactively iteratively to reduce an error between values of the airflow determined according to the model and values of the airflow measured during the operation . Next , the method models the airflow using the updated model and controls the operation of the air - conditioning system using the model .

Concomitant Crystallization In Propylene/Ethylene Random Copolymer With Strong Flow At Elevated Temperatures, Lirong Zheng, Lucia Fernandez-Ballester, Gerrit W. M. Peters, Zhe Ma

Department of Mechanical and Materials Engineering: Faculty Publications

Flow-induced crystallization of α- and γ-phases was studied for a propylene/ethylene random copolymer with 3.4 mol % ethylene at two high temperatures of 132 and 142 °C by combining a pressure-driven slit flow device with real-time synchrotron wide-angle X-ray diffraction. At 132 °C, it was found that both α- and γ-phases were generated at shear stresses ranging from 0.091 to 0.110 MPa and that the γ-phase always appeared later than the α-phase. However, for 142 °C and the same stresses, only the α-phase formed. Only upon cooling the partially crystallized copolymer did the γ-phase emerge. The lack of γ-crystals obtained …

Using The Soar Approach To Teach Middle School Students About Math And Science Concepts Found In Engineering, Rachael Wagner

Honors Theses

In order to address the lack of knowledge about the engineering profession in middle-level students, the project described in this Honors Thesis was developed. Through the creation of an afterschool program centered on engineering, students were able to apply the math and science concepts covered to design, build, and test a bridge. One particular lesson from this after-school program was highlighted in this thesis, the lesson covering the Pythagorean Theorem, to demonstrate the use of SOAR methodology in the lesson’s development and later use in the classroom. The effectiveness of the Pythagorean Theorem lesson was evaluated positively based on the …

Development Of A Model To Predict The Likelihood Of Complaints Due To Assorted Tone-In-Noise Combinations, Joonhee Lee, Lily M. Wang

Durham School of Architectural Engineering and Construction: Faculty Publications

This paper develops a model to predict if listeners would be likely to complain due to annoyance when exposed to a certain noise signal with a prominent tone, such as those commonly produced by heating, ventilation, and air-conditioning systems. Twenty participants completed digit span tasks while exposed in a controlled lab to noise signals with differing levels of tones, ranging from 125 to 1000 Hz, and overall loudness. After completing the digit span tasks under each noise signal, from which task accuracy and speed of completion were captured, subjects were asked to rate level of annoyance and indicate the likelihood …

Peridynamic Modeling Of Dynamic Fracture In Bio-Inspired Structures For High Velocity Impacts, Sneha Akula

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Bio-inspired damage resistant models have distinct patterns like brick-mortar, Voronoi, helicoidal etc., which show exceptional damage mitigation against high-velocity impacts. These unique patterns increase damage resistance (in some cases up to 3000 times more than the constituent materials) by effectively dispersing the stress waves produced by the impact. Ability to mimic these structures on a larger scale can be ground-breaking and could be used in numerous applications. Advancements in 3D printing have now made possible fabrication of these patterns with ease and at a low cost. Research on dynamic fracture in bio-inspired structures is very limited but it is …

Temperature And Stress Analysis During Tank Decanting And Refilling Process, Zhe Liu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

In the present work, an analytical expression for the temperature distribution of the cross-section of a natural gas transport tank is derived by time-matching Green’s Function method. The tank decanting process can produce a living temperature decrease inside the tank wall while the filling process can produce a large temperature increase. This behavior can cause damage to the inner layer of the tank. The damage occurs in the form of excessive stress in the wall which is combined mechanical stress and thermal stress. Therefore, thermo-elasticity analysis is another objective of the present work. A simplified mechanical model is established in …

Rare Earth - Free Permanent Magnetic Material, Laura H. Lewis, Jeffrey E. Shield, Katayun Barmak Viziri

Department of Mechanical and Materials Engineering: Faculty Publications

The invention provides rare earth - free permanent magnetic materials and methods of making them . The materials can be used to produce magnetic structures for use in a wide variety of commercial applications , such as motors , generators , and other electromechanical and electronic devices . Magnets fabricated using the materials can be substituted for magnets requiring rare earth elements that are costly and in limited supply . The invention provides two different types of magnetic materials . The first type is based on an iron - nickel alloy that is doped with one or more doping elements …

Method Of Fabricating A Continuous Nanofiber, Yuris Dzenis

Department of Mechanical and Materials Engineering: Faculty Publications

A method of fabricating a continuous nanofiber is described . The method includes preparing a solution of one or more polymers and one or more solvents and electrospinning the solution by discharging the solution through one or more liquid jets into an electric field to yield one or more continuous nanofibers . The electrospinning process ( i ) highly orients one or more polymer chains in the one or more continuous nanofibers along a fiber axis of the one or more continuous nanofibers , and ( ii ) suppresses polymer crystallization in the one or more continuous nanofibers . The …

Modeling Residual Stress Development In Hybrid Processing By Additive Manufacturing And Laser Shock Peening, Guru Charan Reddy Madireddy

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The term “hybrid” has been widely applied to many areas of manufacturing. Naturally, that term has found a home in additive manufacturing as well. Hybrid additive manufacturing or hybrid-AM has been used to describe multi-material printing, combined machines (e.g., deposition printing and milling machine center), and combined processes (e.g., printing and interlayer laser re-melting). The capabilities afforded by hybrid-AM are rewriting the design rules for materials and adding a new dimension in the design for additive manufacturing paradigm. This work focuses on hybrid-AM processes, which are defined as the use of additive manufacturing (AM) with one …

Effect Of Shot Peening On Stress Corrosion Behavior Of Biodegradable Magnesium We43, Tejaswita Patil

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Conventionally used metals for orthopedic devices made of titanium, stainless steel, and Co-Cr alloys are designed to be permanently implanted. However, long-term complications arise and a secondary implant removal surgery is often necessary. A mismatch in stiffness between the bone and implant results in stress shielding that negatively affects bone density. To overcome these problems, magnesium alloys (e.g., WE34) are favored due to a lower Young’s modulus (45 GPa) and biodegradability. The critical technical barrier with magnesium alloys is their high corrosion rate in physiological (salt-based) environments. One solution is to use surface treatments, such as shot peening (SP), to …

Method For Data - Driven Learning - Based Control Of Hvac Systems Using High - Dimensional Sensory Observations, Amir-Massoud Farahmand, Saleh Nabi, Piyush Grover, Daniel Nikolaev Nikovski

Department of Mechanical and Materials Engineering: Faculty Publications

A controller for controlling an operation of an air - conditioning system conditioning an indoor space includes a data input to receive state data of the space at multiple points in the space , a memory to store a code of a reinforcement learning algorithm and a history of the state data and a history of control commands having been applied to the air - conditioning system , wherein the history of the control commands is associated with the state data and history of rewards , a processor coupled to the memory determines a value function outputting a cumulative value …

Ring And Peg Simulation For Minimally Invasive Surgical Robot, Evan Brown

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Surgical procedures utilizing minimally invasive laparoscopic techniques have shown less complications, better cosmetic results, and less time in the hospital than conventional surgery. These advantages are partially offset by inherent difficulties of the procedures which include an inverted control scheme, instrument clashing, and loss of triangulation. Surgical robots have been designed to overcome the limitations, the Da Vinci being the most widely used. A dexterous in vivo, two-armed robot, designed to enter an insufflated abdomen with a limited insertion profile and expand to perform a variety of operations, has been created as a less expensive, versatile alternative to the Da …

The Effect Of Poly (Glycerol Sebacate) Incorporation Within Hybrid Chitin–Lignin Sol–Gel Nanofibrous Scaffolds, Tuerdimaimaiti Abudula, Lassaad Gzara, Giovanna Simonetti, Ahmed Alshahrie, Numan Salah, Pierfrancesco Morganti, Angelo Chianese, Afsoon Fallahi, Ali Tamayol, Sidi A. Bencherif, Adnan Memic

Department of Mechanical and Materials Engineering: Faculty Publications

Chitin and lignin primarily accumulate as bio-waste resulting from byproducts of crustacean crusts and plant biomass. Recently, their use has been proposed for diverse and unique bioengineering applications, amongst others. However, their weak mechanical properties need to be improved in order to facilitate their industrial utilization. In this paper, we fabricated hybrid fibers composed of a chitin–lignin (CL)-based sol–gel mixture and elastomeric poly (glycerol sebacate) (PGS) using a standard electrospinning approach. Obtained results showed that PGS could be coherently blended with the sol–gel mixture to form a nanofibrous scaffold exhibiting remarkable mechanical performance and improved antibacterial and antifungal activity. The …

The Positive Role Of Curcumin-Loaded Salmon Nanoliposomes On The Culture Of Primary Cortical Neurons, Mahmoud Hasan, Shahrzad Latifi, Cyril J.F. Kahn, Ali Tamayol, Rouhollah Habibey, Elodie Passeri, Michel Linder, Elmira Arab-Tehrany

Department of Mechanical and Materials Engineering: Faculty Publications

Curcumin (diferuloylmethane) is a natural bioactive compound with many health-promoting benefits. However, its poor water solubility and bioavailability has limited curcumin’s biomedical application. In the present study, we encapsulated curcumin into liposomes, formed from natural sources (salmon lecithin), and characterized its encapsulation efficiency and release profile. The proposed natural carriers increased the solubility and the bioavailability of curcumin. In addition, various physico-chemical properties of the developed soft nanocarriers with and without curcumin were studied. Nanoliposome-encapsulated curcumin increased the viability and network formation in the culture of primary cortical neurons and decreased the rate of apoptosis.

Eigenstrain As A Mechanical Set-Point Of Cells, Shengmao Lin, Marsha C. Lampi, Cynthia A. Reinhart-King, Gary C.P. Tsui, Jian Wang, Carl A. Nelson, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Cell contraction regulates how cells sense their mechanical environment. We sought to identify the set-point of cell contraction, also referred to as tensional homeostasis. In this work, bovine aortic endothelial cells (BAECs), cultured on substrates with different stiffness, were characterized using traction force microscopy (TFM). Numerical models were developed to provide insights into the mechanics of cell–substrate interactions. Cell contraction was modeled as eigenstrain which could induce isometric cell contraction without external forces. The predicted traction stresses matched well with TFM measurements. Furthermore, our numerical model provided cell stress and displacement maps for inspecting the fundamental regulating mechanism of cell …

Ureteral Tunnel Length Versus Ureteral Orifice Configuration In The Determination Of Ureterovesical Junction Competence: A Computer Simulation Model, Carlos A. Villanueva, J. Tong, Carl A. Nelson, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction The long-held belief that a ureteral re-implant tunnel should be five times the diameter of the ureter, as proposed by Paquin in 1959, ignores the effect of the orifice on the occurrence of reflux. In 1969, Lyon proposed that the shape of the ureteral orifice (UO) is more important than the intravesical tunnel. However, both theories missed quantitative evidence from principles of physics. The goal of the current study was to test Lyon’s theory through numerical models (i.e. to quantify the sensitivity of ureterovesical junction (UVJ) competence to intravesical tunnel length and to the UO).

Materials and methods The …