Engineering Commons^™

Automated Analysis Of Fluorescent Microscopic Images To Identify Protein-Protein Interactions, Sankar Venkataraman

Masters Theses

The identification and confirmation of protein interactions significantly challenges the field of systems biology and related bio-computational efforts. The identification of protein-protein interactions along with their spatial and temporal localization is useful for assigning functional information to proteins. Fluorescence microscopy is an ideal method for assessing protein localization and interactions as a number of techniques and reagents have been described. Historically, data sets obtained from fluorescence microscopy have been analyzed manually, a process that is both time consuming and tedious. The development of an automated system that can measure the location and dynamics of interacting proteins inside a live cell …

Design Of A Novel Reluctance Motor For Industrial Applications, Weston Clute Johnson

Masters Theses

A novel reluctance motor topology, termed the Johnson-Currie Reluctance Motor (JCRM), has been developed and described in this thesis. The JCRM topology and analysis is based upon the traditional switched reluctance motor (SRM) topology although there are significant modifications.

The flux path of the JCRM topology is such that it passes through the rotor and stator in three-dimensions. This topology with three dimensional flux paths allows for the removal of discrete stator windings giving rise to vastly superior maintance to the traditional SRM and arguably to most electric motors. In addition, the usage of three-dimensions for flux paths gives rise …

Bench Scale Evaluation Of Dense Ceramic Membranes For Production Of High Purity Hydrogen From Gasification, Binay Kumar Singh

Masters Theses

Gasification for production of hydrogen and other useful gases, has achieved increasing importance in recent years. The reactions involved in gasification are favored at high temperatures and they are also limited by thermodynamic equilibrium. The development of membranes which can separate these gases under gasifier exit gas condition will significantly improve process efficiency and economics and simultaneously provide for the recovery of valuable gases. The availability of a membrane with adequate hydrogen selectivity and good thermal and mechanical stability is the key for the successful application of membrane technology in hydrogen production and separation. This work introduces a special method …

Managing The Remaining Service Life Of The T-34c Aircraft, John Howard Rousseau

Masters Theses

The T-34C Airplane has been the primary trainer aircraft of the United States Navy for more than twenty-five years and is reaching the end of its service life. The Navy has delayed the procurement of the replacement T-6A Texan II aircraft for five years, yet does not expect the future training requirements to diminish. This delay in T-6A procurement along with recent observed increases in primary trainer aircraft usage have resulted in the need for the Navy to pay considerable attention to the remaining service life of the T-34C aircraft.

This thesis will discuss the methodology used to determine future …

A Dynamic Ampacity Model For The Testing Of Advanced Conductors, Matthew Benjamin Sooter

Masters Theses

Advanced Conductors are an intriguing new technology that promises to help the utility industry increase the transmission capacity available in the United States. Manufacturers of advanced conductors promise double the current carrying capacity of normal Aluminum Clad Steel Reinforced conductor through a combination of increased thermal limits and decreased thermal elongation.

This thesis will outline a control developed for the Power Line Conductor Accelerated Test Facility at Oak Ridge National Laboratory. This custom facility is designed for the testing and rapid aging of advanced overhead conductors as part of a U.S. Department of Energy initiative to assist the development and …

Comparison Of Microscopic Modalities For The 3d Model Reconstruction Of Nanodevices, Christopher Robert Kammerud

Masters Theses

As manufacturing capabilities push nanotechnology to smaller and smaller scales, novel inspection schemes must be developed to ensure product quality. The objective of our research was to implement, refine, and compare 3D reconstruction algorithms that could aid manufacturers in their ability to visualize and inspect nanodevices. Data was collected from three different microscopes: the atomic force microscope (AFM), the scanning electron microscope (SEM), and the laser scanning confocal microscope (LSCM). For each of these microscopes, a specific algorithm was implemented to generate 3D models from the raw microscope data. Scans from the AFM microscope give range information similar to laser …

A Statistical Based Model To Manage Perishable Goods Within A Cold Supply Chain, Amanda Rhiana Hicks

Masters Theses

"Cold chain" management, the management of a temperature sensitive supply chain, has its own particular set of logistical challenges and issues when compared to a non-temperature sensitive supply chain. Current supply chain management techniques and tools that are utilized today in industry do not take this unique set of challenges into account. This thesis will focus on how using a model that has been built upon the theories of statistical process control techniques that does take the challenges into account, when monitoring and evaluating in-transit shipment of perishable goods throughout the cold supply chain, can assist in continuously improving the …

A K-Epsilon Extension For Wall-Bounded Flows On The Broadband Aeroacoustic System Simulator, David González

Masters Theses

The turbulence modeling capabilities of the Broadband Aeroacoustic System Simulator (BASS), an experimental code developed at NASA Glenn Research Center, have been extended to include wall-bounded flow capabilities. This was done by first validating the code's viscous solving routines by comparing numerical solutions to known, simple analytic solutions. Finally, the dynamics of the wall shear flows were accounted for with the use of wall-damping functions incorporated into the turbulence model. The results for both viscous and turbulence routines agree well with published data.

Evaluation Of Engineering Plastic For Rollover Protective Structure Mounting, Robert Stephen Comer

Masters Theses

The agricultural industry has one of the highest fatality rates of any industry in the U. S. This death rate is largely due to deaths caused by roll over accidents while on agricultural vehicles. The addition of a Rollover Protective Structure (ROPS) has aided in lowering these high fatality rates on full-size tractors. Studies have shown that death rates have been reduced by as much as 98% with the addition of rollover protective structures. However, a large number of older tractors still do not utilize a ROPS. This is due to the difficulty of designing and creating a mounting structure. …

A Comparison Of The Sensor Brick Concept As A Modular System Architecture To The Realtime Control System As The Operational Architecture, James Robert Wilson

Masters Theses

This thesis describes the application of modular design into an intelligent mobile robotic system. The Sensor Brick System, a mobile robotic system infused with artificial intelligence, is derived through the concept and application of modular design. Modular design drives the system’s characterization by defining, identifying and selecting the essential composite of sub-systems that form the system architecture. The principles of modular design designate grouping the technologies into modules that facilitate maintenance of the system components and allow the rapid integration of future technological developments. Developing the operational control of the system requires an examination and comprehension of the theories of …

An Experimental Study Of Axisymmetric Cavity Oscillations In Low Speed Incompressible Flow, Jeremy David Brice Smith

Masters Theses

This study is the latest increment of an ongoing research effort at the University of Tennessee Space Institute with the goal of accomplishing a greater understanding of cavity instabilities and or making use of the instabilities to amplify their effects on the flows. An experimental procedure was designed to examine the unsteady pressure pulses that occur when an incompressible fluid (water) flows through an axisymmetric cavity. The length to depth ratios (L/D) examined ranged from about 0.69 to about 6.2, and the average flow Reynolds numbers ranged from 0 to 1.2 million.

Results show that large amplitude oscillations are generated …

Approaches For Autonomous Vehicles In Civil Airspace: Giving Sight To The Blind, Nicholas Scott Hardman

Masters Theses

The growing prevalence of unmanned aerial vehicles (UAVs) brings great potential for public benefit, but in order to fly in civil airspace UAVs must avoid traffic without the benefit of an onboard human. Developing this capability presents many system integration challenges.

This report examines the integration of automated detect, see, and avoid (DSA) systems on aircraft. For context, the need for UAV operations is reviewed. The report then examines how DSA fits into the entire framework for aviation safety. The research, test results, and conclusions that follow provide the necessary information to decide:

• how to test and evaluate new …

Simulating Discriminatory Profiling, Oscar Neal

Masters Theses

There is a concern that racial profiling is being used to invoke searches and stops in spite of its violation of the fourth amendment. Simulation methods are used to study the correlation test of stops, searches and citations with race, age, and gender. The design uses sensitivity analysis of inputs to determine their relationship to outputs statistics of a police department's citations and stops. Experimental results are than used to verify and predict departmental bias. A simulation program written in Visual Basic is used as a tool to explore simulation techniques. A formulation of simulation uses in studying discriminatory profiling …

Experimental Aerodynamic Analysis Of A Wing-Flap System With Delta Vortex Generators, Charles Roy Mcconnell

Masters Theses

The principle idea upon which the use of vortex generators (VGs) is based has been to control flow separation. The characteristic of VGs has been used to improve lift and alter the stall characteristics of aircraft and has been a relatively common practice for many years. Due to the seemingly limitless range of VG geometries and arrangements, which are largely dependant upon the desired aerodynamic performance, there has been a broad investigation into VG application.

The purpose of this experimental investigation has been to collect data to be used to establish the effects of various delta shaped vortex generators (delta-VGs) …

Optimization Of Dsss Receivers Using Hardware-In-The-Loop Simulations, Balbir Kaur Dhillon

Masters Theses

Over the years, there has been significant interest in defining a hardware abstraction layer to facilitate code reuse in software defined radio (SDR) applications. Designers are looking for a way to enable application software to specify a waveform, configure the platform, and control digital signal processing (DSP) functions in a hardware platform in a way that insulates it from the details of realization.

This thesis presents a tool-based methodolgy for developing and optimizing a Direct Sequence Spread Spectrum (DSSS) transceiver deployed in custom hardware like Field Programmble Gate Arrays (FPGAs). The system model consists of a tranmitter which employs a …

Propeller Development Process: Conflict And Cooperation Between The Department Of Defense And Civil Aviation, Nathan Grant Neblett

Masters Theses

The purpose of this thesis was to compare and contrast the acquisition of the Electronic Propeller Control System through both the Department of Defense and Civil Aviation processes controlled by the Federal Aviation Administration (FAA). The author was a planner and participant in the Department of Defense (DoD) process. Information about the Civil Aviation process was obtained via email and telephone communication with participants, some of whom aided both processes.

Strong similarities existed in system design and prototype manufacture for both processes. A large portion of developmental flight test was similar, if not identical. In particular, both the DoD and …

Evaluation Of Mechanical Properties Of Recycled Aggregate Concrete, Sajjad Ali Khan

Masters Theses

The maintenance and repair work in the civil engineering infrastructures develops the production of huge wastes which causes the growth of waste piles, additional costs in construction projects and some environmental problems. If this waste is recycled and used again in construction projects, it will help to overcome the problems discussed earlier. Moreover, if natural aggregates are supplemented by recycled aggregate, it will preserve the natural resources and also put a pause in the deterioration of natural landscape.

This thesis addresses the importance of using recycled aggregate in concrete structures. Its practical feasibility in construction projects is studied in light …

Mixing Flow Structures Of Scalloped, Forced Lobed Mixers Using Piv And Plif Measuring Techniques, Nathan J. Cooper

Masters Theses

An Experimental study of internal forced lobed mixers similar to those used in jet aircraft engines is performed using whole field species concentration and velocity measuring techniques. Planar temperature and velocity measurements using Planar Laser Induced Fluorescence (PLIF) and 2D Particle Image Velocimetry (PIV) are performed for lobed, lobed scalloped and splitter mixers in aqueous solution. Specific emphasis is given to study scallops or notches cut into the mixer trailing edge and their role in mixing enhancement. Mixing is compared through velocity and species concentration measurements on axial and streamwise planes for the three dimensional, forced mixers in a confined …

Evaluation Of Mechanical Properties Of Self-Consolidating Concrete, Bhusan Basnet

Masters Theses

The concept of Self-Consolidating Concrete is a fresh and rapidly ramping technology in USA, but in some other continents such as Japan and Europe it is in fully fledged stage. The development of this technology has a high potential to economize construction minimizing labor, scheduled time and equipment eliminating consolidation process. In USA, construction professionals are reluctant to its in-effect application because of lack of deliberate and methodological steps for production and applications. The lack of study of its durability characteristics and confusion in design and production process are seems to be vital factors hindering full scale production and application …

Ductile Regime Nano-Machining Of Silicon Carbide, Biswarup Bhattacharya

Masters Theses

This thesis describes experimental work carried out to study the ability to ductile . single point diamond turn both polycrystal Silicon Carbide (SiC) and chemically vapor deposited (CVD) SiC. A Precitech diamond turning machine was used for ductile regime machining of polycrystal SiC at depths of 10 and 25 nm. The possibility of machining SiC in the ductile mode was substantiated by post process analysis of the chips collected during machining and the surface profiles. The force data obtained during machining was recorded and compared later with the different depth of cuts. An investigation into the ability to single point …

Determination Of Stiffness Matrix Of Tapered Roller Bearings For Vibration Models, Jeeva Kumar

Masters Theses

The stiffness matrix of tapered roller bearings under radial and axial load conditions was evaluated using an analytical model and an experimental approach. An experimental test system was designed and manufactured to determine the radial stiffness of the bearing under combined axial and radial load conditions. A second fixture was designed to measure the stiffness of the bearing under pure axial load conditions. The stiffness coefficients determined have been compared with those obtained from the analytical model, OEM (Original Equipment Manufacturer) data and ABAQUS model (finite element analysis software).

Guidelines To Select A Computerized Maintenance Management System, Dattaraj Kamalapurkar

Masters Theses

In today's highly competitive global economy, maintenance personnel are presented with more difficult challenges than at any previous point in time. In order to meet these challenges, many maintenance managers tend to rely . on Computerized Maintenance Management System (CMMS). When properly selected and implemented, CMMS is one of the most powerful cost reduction tools in any organization. However in reality, many CMMS implementations fail rather than achieve success. While there are many contributing factors, one major factor that greatly impacts successful implementation is selecting the right CMMS system. With more than 200 CMMS systems to choose from, selecting the …

Enhancing System-On-Chip Verification Using Embedded Test Structures, Wei Jiang

Masters Theses

In this project, we designed and implemented a System-on-Chip platform with embedded test structures. The baseline platform consists of a Leon2 CPU, AMBA on-chip bus, and an Advanced Encryption Standard decryption module. Reconfigurable test logic blocks were embedded to form the test structure that can be used in post-silicon debug and verification.

The System-on-Chip platform was designed at the register transistor level and implemented in an 180nm CMOS process. Test logic instrumentation was done with DAFCA, Inc. (Design Automation for Flexible Chip Architecture) pre-silicon tools. The design was then synthesized using the Synopsys Design Compiler and placed and routed using …

Universal Geometric Camera Calibration With Statistical Model Selection, Chistopher Paul Broaddus

Masters Theses

We propose a new universal camera calibration approach that uses statistical information criteria for automatic camera model selection. It requires the camera to observe a planar pattern from different positions, and then closed-form estimates for the intrinsic and extrinsic parameters are computed followed by nonlinear optimization. In lieu of modeling radial distortion, the lens projection of the camera is modeled, and in addition we include decentering distortion. This approach is particularly advantageous for wide angle (fisheye) camera calibration because it often reduces the complexity of the model compared to modeling radial distortion. We then apply statistical information criteria to automatically …

“Design And Verification Of A Reusable Self-Reconfigurable Gate Array Architecture, Gabriel Cozmin Chereches

Masters Theses

This thesis presents the design and verification of a Self-Reconfigurable Gate Array architecture (SRGA-UT) created for reuse, and available with a step-by-step tutorial and comprehensive documentation. The original SRGA [1], created at the University of Southern California, is an innovative architecture for a reconfigurable device that allows single cycle context switching and single cycle random access to a unified on-chip configuration/data memory. The key architecture that enables the above two features is the use of a mesh of trees based interconnect with logic cells and memory blocks at the leaf nodes and identical switches at the parent nodes.

The SRGA-UT …

Bio-Derived Fuels For Hybrid Rocket Motors, Joshua David Scholes

Masters Theses

Two bio-derived fuels have been successfully tested in a laboratory scale hybrid rocket combustion chamber located at the University of Tennessee, Knoxville. Pure lard soaked in an open cell sponge matrix and beeswax were both tested using gaseous oxygen as the oxidizer. Given similar testing conditions, these fuels exhibit higher regression rates than the common hybrid rocket propellant HTPB (hydroxyl-terminated polybutadiene), thus overcoming one of the main shortcomings of hybrid rocket fuels. These fuels also have similar or higher regression rates than paraffin-based fuels recently tested by a Stanford University/NASA Ames team. Measured thrusts ranged from 20-140 Newtons, and calculated …

Comparative Properties Of Polymers Guiding The Development Of An Abdominal Aorta Model, Benjamin Michael Lamie

Masters Theses

Hemodynamics, the study of the forces involved in the circulation of blood, is an area that researchers have approached in various manners for many years. The study of how blood flows through arteries and veins as well as the effect of the composition of the blood has been defined and thoroughly characterized in past studies. Although in-depth studies have been performed on the flow characteristics of blood, most often the observations are made as the fluid flows through tubes composed of some rigid material. It is well known that the arteries and veins have a layered histology that show varying …

Effect Of Hydrogenon On Mechanical Behavior Of A Zircaloy-4 Alloy, Elena Garlea

Masters Theses

Hydride formation is one of the main degradation mechanisms of zirconium alloys in hydrogen-rich environments. When sufficient hydrogen is present, zirconiumhydride precipitates can be formed. Cracking of the brittle hydrides near a crack tip can initiate the growth of a crack leading to the premature failure of the material. Hydride formation is believed to be enhanced by the presence of residual or applied stresses. Therefore, the increase in the stress field ahead of a crack tip may promote precipitation of additional hydrides. In order to verify these phenomena, the effect of internal stresses on the zirconium-hydride-precipitate formation, and in turn, …

The Development Of Qualification Standards For Cast Super Duplex Stainless Steel (2507 Wrought Equivalent), Vasudevan Hariharan

Masters Theses

The objective of the program is to determine the suitability of ASTM A923 “Standard Test methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic-Ferritic Stainless Steels” for 25 Cr Cast Super Duplex Stainless Steels (ASTM A890-5A).

Different tests were carried out on the materials procured from various steel foundries as stated in the ASTM A923. The foundries were designated as Foundry A, B, C and D. All the materials were foundry solution annealed. Materials from Foundry D were solution heat treated at The University of Tennessee also and then they were subjected to heat treatment schedule which was derived …

Synthesis, Microstructure, And Mechanical Behavior Of Fe-Cu Composites, Jin-Woo Jeon

Masters Theses

The synthesis, microstructure, and mechanical properties of ball-milled nanocrystalline (nc) Fe powder and immiscible Fe-Cu alloy composites are investigated in this thesis. Experimental approaches are described for the characterization of the grain size and hardness of nc Fe powders and the internal stress state of bulk Fe-Cu alloy composites are presented.

The grain size measurements of ball-milled Fe powders obtained from the XRD line broadening analysis (15 nm) and TEM observation (18 nm) showed good agreement between two results. From the nanoindentation tests, the hardness values of the ball-milled Fe powders were increased from 3.5 to 10.5 GPa as the …