Engineering Commons^™

Electromagnetic Formation Control Using Frequency Multiplexing, Zahra Abbasi

Theses and Dissertations--Mechanical Engineering

This dissertation addresses control of relative positions and orientations of formation flying satellites using magnetic interactions. Electromagnetic formation flight (EMFF) is implemented, in which each satellite is equipped with a set of electromagnetic coils to generate an electromagnetic field. Traditional EMFF technique applies DC magnetic fields which lead to a nonlinear and highly coupled formation dynamics that allow for only position or orientation control of the satellites. We present a new frequency multiplexing method, which is a technique that uses multi-frequency sinusoidal controls, to approximately decouple the formation dynamics and to provide enough controls for both position and orientation control. …

Design And Process Of 3d-Printed Parts Using Composite Theory, Jordan Garcia

Theses and Dissertations--Mechanical Engineering

3D printing is a revolutionary manufacturing method that allows the productions of engineering parts almost directly from modeling software on a computer. With 3D printing technology, future manufacturing could become vastly efficient. However, it is observed that the procedures used in 3D printing differ substantially among the printers and from those used in conventional manufacturing. In this thesis, the mechanical properties of engineering products fabricated by 3D printing were comprehensively evaluated and then compared with those made by conventional manufacturing. Three open-source 3D printers, i.e., the Flash Forge Dreamer, the Tevo Tornado, and the Prusa, were used to fabricate the …

Mathematical Modeling For Platform-Based Product Configuration Considering Total Life-Cycle Sustainability, Tian Lan

Theses and Dissertations--Mechanical Engineering

Many companies are using platform-based product designs to fulfill the requirements of customers while maintaining low cost. However, research that integrates sustainability into platform-based product design is still limited. Considering sustainability during platform-based design process is a challenge because the total life-cycle from pre-manufacturing, manufacturing and use to post-use stages as well as economic, environmental and societal performance in these stages must be considered. In this research, an approach for quantifying sustainability is introduced and a mathematical model is developed for identifying a more sustainable platform. Data from life-cycle assessment is used to quantify environmental factors; criteria from the Product …

Estimating Passive Material Properties And Fiber Orientation In A Myocardial Infarction Through An Optimization Scheme Using Mri And Fe Simulation, Dimitri Mojsejenko

Theses and Dissertations--Mechanical Engineering

Myocardial infarctions induce a maladaptive ventricular remodeling process that independently contributes to heart failure. In order to develop effective treatments, it is necessary to understand the way and extent to which the heart undergoes remodeling over the course of healing. There have been few studies to produce any data on the in-vivo material properties of infarcts, and much less on the properties over the time course of healing. In this paper, the in-vivo passive material properties of an infarcted porcine model were estimated through a combined use of magnetic resonance imaging, catheterization, finite element modeling, and a genetic algorithm optimization …

A Metrics-Based Sustainability Assessment Of Cryogenic Machining Using Modeling And Optimization Of Process Performance, Tao Lu

Theses and Dissertations--Mechanical Engineering

The development of a sustainable manufacturing process requires a comprehensive evaluation method and fundamental understanding of the processes. Coolant application is a critical sustainability concern in the widely used machining process. Cryogenic machining is considered a candidate for sustainable coolant application. However, the lack of comprehensive evaluation methods leaves significant uncertainties about the overall sustainability performance of cryogenic machining. Also, the lack of practical application guidelines based on scientific understanding of the heat transfer mechanism in cryogenic machining limits the process optimization from achieving the most sustainable performance.

In this dissertation, based on a proposed Process Sustainability Index (ProcSI …

Experimental Investigation To Inform Optimal Configurations For Dynamic Near-Field Passive Uhf Rfid Systems, Donnie E. Proffitt Ii

Theses and Dissertations--Mechanical Engineering

RFID has been characterized as a “disruptive technology” that has the potential to revolutionize numerous key sectors. A key advantage of passive RFID applications is the ability to wirelessly transmit automatic identification and related information using very little power. This paper presents an experimental investigation to inform the optimal configuration for programming passive ultra-high frequency (UHF) RFID media in dynamic applications. Dynamic programming solutions must be designed around the tag’s functionality, the physical programming configuration and environment. In this investigation, we present a methodology to determine an optimal configuration to maximize the systems programming efficiency for dynamic applications.

Temperature And Strain Controlled Optimization Of Stabilization Of Polyacrylonitrile Precursor Fibers, Mark Parr Taylor

Theses and Dissertations--Mechanical Engineering

Carbon fiber is one of the leading materials for high strength and modulus, and light weight applications. Improvements in carbon fiber properties are directly dependent on all aspects of manufacture, especially the process of stabilization. Therefore, it is the goal of this thesis to study the effects of the temperature and strain profile of the stabilization process, and the resulting carbon fiber tensile properties. In addition, the precursor fibers used were spun under two different draw ratios, to study the effects of the spinning parameters. Results indicated through DMA studies that completeness of stabilization reactions can be gauged by the …