Engineering Commons^™

On-Demand Label Production, Robert A. Zimmerman

Master's Theses

The production and approval process for the various labels used in clinical trials wastes significant time and resources through the need to outsource label production or rely on large reams of pre-cut label stock for each revision throughout the process. An in-house, on-demand label printing and cutting system is a potential remedy to this waste. Previous work by Cheadle et al. resulted in a functional electomechanical prototype of the label cutting aspect of this research, capable of rudimentary linear cuts. In this continued research, emphasis was placed on improved label cutting capabilities and creating PC control software for label design. …

Scaled Synthetic Aperture Rader Development, Jason Garvey Schray

Master's Theses

Several previous Cal Poly thesis projects involve synthetic aperture radar (SAR), automatic target recognition (ATR), and tracking. SAR data was either accessed from a publicly available database or generated using complex computer modeling software. The motivation for this dual thesis project is to design and construct a scaled SAR system to support Cal Poly radar projects. Ideally this is a low-cost, high resolution SAR architecture that produces raw range Doppler data for any desired target area. To that end, a scaled SAR system was successfully designed, built, and tested. The current SAR system, however, does not perform azimuthal compression and …

Ncma Groundwater Model Using Usgs Modflow-2005/Pest, Brian Matthew Wallace

Master's Theses

A numerical model for the NCMA aquifer complex is presented. The objective of the study is to develop a numerical groundwater model for the NCMA aquifer system to enhance the understanding of subsurface groundwater flow. Infiltration, streamflow, pumping, and return flows are implemented to characterize the aquifer complex over time. The numerical model is calibrated to municipal and monitoring well data, average monthly water balances, and hydraulic contours. Transient aquifer inflows and outflows are assessed in the results of the study and are compared to balance terms from previous studies. The 2007 Todd Engineers Study subsurface inflows and outflows generate …

Eurotech Students In Germany: Preparation, Experience And Outcome, Daisy A. Michaels

Master's Theses

Higher education study abroad programs for U.S. students are on the rise. A variety of undergraduate disciplines are being coupled with international components to bring U.S. students to a higher level of global awareness to meet the demands of today’s economy. The University of Connecticut’s Eurotech Program is an example of this trend. Its students earn degrees in both German and engineering in a five year program. They are given practical training through study and internships in Germany under the auspices of the Baden-Württemberg Exchange Program. One of the Eurotech Program’s major goals is to enhance job opportunities for its …

Automation Of Orthodontic Wire Tester For Performing Three Point Bending Tests, Adithya Venkatesan

Master's Theses

Abstract

Understanding the biomechanical factors in orthodontics is important in order to improve the overall effectiveness of actual clinical treatment. An accurate method to study the threedimensional (3D) force systems and the resulting movements of teeth during orthodontic treatment is needed along with the understanding of the material properties of any orthodontic wire. Until recently, most of the orthodontic biomechanics literature was limited to twodimensional experimental studies. Recent advances in threedimensional computer modeling have also been developed but have been limited to the manual control of tooth movement. Overall, there is very little published evidence in the literature on the …

Thermodynamic Based Model Eliciting Activities For Undergraduate Mechanical Engineering Education, Paul Nicholas Van Bloemen Waanders

Master's Theses

Undergraduate engineering education is designed to prepare students for their careers. The rise of technology in modern engineering allows for a shift in the way undergraduates are prepared for the modern workplace. Model Eliciting Activities (MEAs) allow students to think critically about their own work and allow instructors to analyze the students’ problem solving methods. To ensure that new MEAs are as effective as possible they are subject to six basic principles: model construction, reality, generalizability, self-assessment, model documentation, and effective prototype.

This document focuses on evaluating new MEAs for their adherence to the six principles from an instructor's and …

Implementation Of Physiologic Pressure Conditions In A Blood Vessel Mimic Bioreactor System, Kevin Mark Okarski

Master's Theses

ABSTRACT

Implementation of Physiologic Pressure Conditions in a Blood Vessel Mimic Bioreactor System

Kevin Mark Okarski

Tissue engineering has traditionally been pursued as a therapeutic science intended for restoring or replacing diseased or damaged biologic tissues or organs. Cal Poly’s Blood Vessel Mimic Laboratory is developing a novel application of tissue engineering as a tool for the preclinical evaluation of intravascular devices. The blood vessel mimic (BVM) system has been previously used to assess the tissue response to deployed stents, but under non-physiologic conditions. Since then, efforts have been made to improve the vessel and bioreactor’s ability to emulate in …