Engineering Commons^™

Development Of Self-Stressing Ultra High-Performance Concrete Using Expansive Chemical Admixtures, Lane Edwards

Graduate Theses and Dissertations

This study investigated the effects of expansive chemical admixtures on ultra-high performance concrete (UHPC) and self-stressing mechanisms. A literature review was performed to determine different types of expansive admixtures for feasibility of the self-prestressing concept. Ultimately it was decided that type-k cement, made by combining Komponent admixture with conventional UHPC, was the most suitable option due to its effects on wet and hardened concrete properties. Mix designs with varying amounts of Komponent were developed to test the effects the admixture had on various properties. Tested properties included, workability, compressive strength, expansion, short-term shrinkage, long-term shrinkage, and developed prestress. The development …

Nondestructive Evaluation Of Structural Defects In Concrete Slabs, Ehsanul Kabir

Electronic Theses and Dissertations

Nondestructive testing (NDT) is a reliable method for determining the structural integrity of new and old construction and understanding the condition of structural defects. It is widely acknowledged that the interpretation of nondestructive evaluation (NDE) has a significant impact on the reliability and consistency of this technology. However, NDT data acquisition remains subjective and heavily dependent on the operator’s knowledge and expertise. As a result, there are still issues to be resolved regarding the imaging and diagnostic procedures for NDT-based concrete inspection. NDT methods such as ground penetrating radar (GPR), and impact-echo (IE), have been extensively used to inspect concrete …

A Study On Early Age Properties Of Concrete For Precast And 3d Printing, Debalina Ghosh

Doctoral Dissertations

Concrete is the second-most consumed material, leading the global Portland cement production of 4.1 billion tons in 2020 and 5-8% of global Carbon dioxide (CO₂) emission annually. As with any other material and practice, the construction industry is also ever-changing to meet market demand, evolving technology, and resource limitation. In the case of concrete construction, one of the main concerns is the lack of automation. In the last few decades, some new construction methods have risen to address this concern. Some of these economic and successful practices are precast construction, self-compacting concrete (SCC), and 3D printing of concrete(3DPC). …

Flexural Bond Strength Of Masonry Assemblies With Lightweight Grout, Benjamin L. Hiner

All Theses

Lightweight grout has many potential benefits in masonry construction, including minimizing mass, improving thermal performance, and potentially reducing shrinkage cracking via internal curing. However, insufficient testing of masonry assemblies with lightweight grout has been conducted to suggest appropriate design modification factors akin to the lambda factor in ACI 318-19. The objective of this paper is to study the tensile bond behavior of masonry assemblies grouted with lightweight grout and to suggest appropriate equations for predicting design capacity. A moment couple test is designed specifically for grouted masonry assemblies and has additional capacity compared to the traditional ASTM 1072 bond wrench …

Evaluating The Effects Of Curing Methods On Bcsa Cement Concrete, Hannah Allen

Civil Engineering Undergraduate Honors Theses

BCSA cement is a type of cement that makes concrete set up much quicker than typical portland cement concrete. BCSA cement concrete also has a much higher compressive strength than that of portland cement concrete. This study was conducted to determine the effect of different curing conditions on the compressive strength of BCSA cement concrete.

A Comparison Of Common Structural Materials, Molly Green

Williams Honors College, Honors Research Projects

This report will compare structural steel, concrete, and lumber through the lenses of mechanical properties, design process, cost, and environmental impact. Steel is a versatile, strong, and lightweight material that comes at a premium price – both financially and environmentally. It is the most expensive material of the three included in this report. This is largely due to its complex manufacturing process that is also responsible for a significant amount of the world’s carbon dioxide emissions. Concrete is significantly less expensive than steel, but the carbon dioxide emissions from manufacturing are approximately equal. Concrete also only performs well in compression …

Shear Strength Of Concrete Beams Made With Belitic Calcium Sulfoaluminate Cement, Caleb W. Chesnut

Graduate Theses and Dissertations

The need for a cleaner alternative to portland cement (PC) concrete has led to increasing interest in alternatives to PC. Structural properties of most of these alternative cements are still an open research topic. One promising alternative cement is belitic calcium sulfoaluminate (BCSA) cement. The study presented in this paper investigated the shear strength, long term compressive strength, and carbonation in BCSA cement and PC concrete beams. A total of twelve eight-foot long beams were made; eight BCSA cement concrete beams and four PC concrete beams to be tested at various ages depending on cement type. Two beams of each …

Assessment Of Key Imperatives For Enhancing Precast Adoptability In Egypt, Mostafa Sameh

Theses and Dissertations

Precast Concrete’s modular application concept is a major construction method that has been used historically seen in various shapes, forms, and with a wide range of constituents. Examples include Ancient Egypt and China among several impressive structures in old civilizations. The major advantages of precast concrete lie in its adaptability, resilience, and versatility which makes precast concrete one of the most agile building materials. Precast concrete as we know it today has been introduced to our markets over the past several decades. Having similar advantages to that of old precast building methods, the road has been paved for wider use …

Effect Of Radiation On Bond Behavior Between Concrete And Steel Bar: Development Of Experimental Protocol, Mohammed Abdelrahman

Masters Theses

There is a need to assess the effect of radiation on the behavior of bond strength between steel reinforcement and concrete. However, there is geometrical constraints in the cylindrical capsule which limit the size of concrete samples. Thus, developing a protocol to produce pullout sample and a test setup is needed.

A protocol for fabricating high-precision concrete samples with embedded \#2 steel bar has been developed based on the results of an experimental program. A pullout system has also been developed to investigate the bond activity of concrete and steel. This research looks at two different aggregate sizes 3/8 inch …

Mitigating Calcium Oxychloride Damage In Cementitious Paste And Concrete Utilizing Supplementary Cementitious Materials, Casey Jones

Graduate Theses and Dissertations

It is understood among engineers in the United States (U.S.) that improvement is needed throughout the transportation infrastructure. In the 2021 Infrastructure Report Card produced by the American Society of Civil Engineers, the roadways of this nation merit a D. This leaves room for improvement in order to provide durable pavements throughout this nation. Areas with significant winter weather may have exacerbated effects in decreased roadway longevity due to freezing/thawing cycles and the use of chemical deicers to mitigate gelid roadway conditions. Much research focuses on surface scaling and reinforcement corrosion using these materials; however, joint deterioration, due to chemical …

Comparison Of The Resistance Of Belitic Calcium Sulfoaluminate Cement And Portland Cement To Sulfate Attack And Sulfuric Acid, Rilye Dillard

Graduate Theses and Dissertations

Microbially induced corrosion (MIC) is a fairly common concrete deterioration mechanism with many negative effects. MIC is a complex chemical and biological process that occurs in sewage systems and is nearly impossible to replicate in a laboratory setting. For this study, sulfate and sulfuric acid attack on concrete were studied to mimic two stages of the MIC process. The ASTM C1012, Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution and a modified ASTM C1012 accelerated method were used to compare the sulfate resistance of belitic calcium sulfoaluminate (BCSA) cement, portland cement (PC), and PC-fly …

Nondestructive Condition Assessment Of Civil Infrastructure Using Ultrasonic Technique, Tyler Keith Ashbrook

Graduate Theses, Dissertations, and Problem Reports

Civil Infrastructure controls the way people live by providing safe passage and shelter across the entire globe. Since safety leads the concern in infrastructure, it is essential to ensure that these structures have been adequately tested and analyzed periodically. Testing these structures can be extremely expensive when parts are required to be removed to capture the flaw, which is why nondestructive testing (NDT) continues to grow in demand since it can evaluate the structural component in-situ without causing any damage. Ultrasonic testing (UT) helps to adequately sustain and advance the safety in existing and future infrastructure across the globe. Continual …

Tanzanian Concrete Masonry Walls, Edward J. Kaminski

Architectural Engineering

Walls that replicate masonry walls used in Tanzania are constructed and tested. The results from testing was compared with the respective predictions made using code guidelines from ASCE 7 and TMS 402.

Machine Learning Prediction Of Shear Capacity Of Steel Fiber Reinforced Concrete, Wassim Ben Chaabene

Electronic Thesis and Dissertation Repository

The use of steel fibers for concrete reinforcement has been growing in recent years owing to the improved shear strength and post-cracking toughness imparted by fiber inclusion. Yet, there is still lack of design provisions for steel fiber-reinforced concrete (SFRC) in building codes. This is mainly due to the complex shear transfer mechanism in SFRC. Existing empirical equations for SFRC shear strength have been developed with relatively limited data examples, making their accuracy restricted to specific ranges. To overcome this drawback, the present study suggests novel machine learning models based on artificial neural network (ANN) and genetic programming (GP) to …

Macro - And Microstructure Evaluation And Field Applications Of Concrete With Recycled Glass Pozzolan, Marija Krstic

Dissertations and Theses

Concrete is the most used material in the world, second only to water. Conventional concrete is produced with Portland cement (PC). The production of cement is an energy intensive operation that has raised significant environmental concerns, since one ton of cement generates an equal ton of CO₂. In the USA about 90 million tons of cement are used annually, with 3 million tons used in New York. Most contemporary concrete applications for buildings and infrastructure use high-performance concrete (HPC) mixtures which are produced by replacing a percentage of cement with supplementary cementitious materials (SCMs), consisting mainly of fly-ash …

Slender Frp Elements As Discrete Reinforcement For Concrete, Yuan Tian

Dissertations and Theses

This dissertation presents a study that led to the development of slender elements that look like fibers used for reinforcing concrete but with a very different reinforcing mechanism. These elements, referred to as “Needles” are very rigid and strong; when intersected by growing cracks in concrete under heavy and increasing loads, they do not break and deform minimally. In the present work major steps were taken to understand the reinforcing mechanism of Needles. In addition, to investigate the influence of Needles on the mechanical performance of concrete incorporating Needles, at both material and structural levels, a series of laboratory experiments …

Evaluation Of Concrete Deck Curing Regimens Using Capillary Pressure Sensing System, Samuel Spann

Graduate Theses and Dissertations

Early-age plastic shrinkage cracking is a common problem with the construction of concrete bridge decks due to the high surface area-to-volume ratio and exposure to potentially detrimental environmental effects. Curing regimens are utilized to mitigate cracking risk during the plastic stage of the concrete; the curing regimens evaluated for this study were wet burlap-polyethylene sheeting, two acrylic curing compounds, and one lithium compound. Capillary pressure in the water filled pores has been shown to correlate to the plastic shrinkage cracking risk of concrete. A new portable system has been developed to measure the capillary pressure that could potentially be used …

Steel Test Set-Up For Non-Ductile Concrete Shear Walls, Colin S. Ridgley

Architectural Engineering

The purpose of this project was to provide a robust test set-up for the thesis work being conducted by graduate students, Jerry Luong & Rory de Sevilla. Their research aims to evaluate the feasibility of using fiber-reinforced polymer wraps and splay anchors to retrofit non-ductile concrete shear walls through a series of tests on reinforced concrete walls.

Four key constraints governed the design of the test set-up. First, the wall can be cyclically, laterally loaded to develop data for comparison with theoretical analysis methods. Second, the wall can be axially loaded to simulate interaction effects and prevent a sliding failure …

The Influence Of Citric Acid On Setting Time And Temperature Behavior Of Calcium Sulfoaluminate-Belite Cement, Edgar Soriano

Civil Engineering Undergraduate Honors Theses

Today the need to opt for alternative cementitious materials is growing due to environmental reasons and construction time frames that portland cement cannot always satisfy. Calcium Sulfoaluminate (CSA) cements are a strong candidate to supplement or replace portland cement in the construction field for certain applications. In the United States, CSA cement has been limited mostly to pavement repairs because of its rapid initial setting time. The chemical compound responsible for this phenomenon is the alumina. This compound and sulfate are present in larger proportions compared to portland cement. The purpose of this research is to study how the use …

Performance Of Concrete Tunnel Systems Subject To Fault Displacement, Michael Morano

Masters Theses

A Finite Element Analysis (FEA) investigation of concrete tunnel systems traversing seismic faults is carried out to determine how to effectively mitigate the stresses induced in the liner when subject to fault displacement. A parametric study of various fault parameters, both in the damage zone and competent rock, is carried out to determine the site conditions which induce the most stress on the tunnel liner system. Results indicate that friction angle, cohesion, and elastic modulus of fault zones have varying effects on the stresses induced on the liner. The width of damage zone and expected displacements are also investigated and …

Design And Performance Of Fiber-Reinforced Concrete With Adapted Rheology For Construction And Repair Of Bridge Structures, Ahmed Abdelrazik

Doctoral Dissertations

“The objective of this document is to design high-performance fiber-reinforced self-consolidating concrete (FR-SCC) for infrastructure repair and fiber-reinforced super-workable concrete (FR-SWC) for bridge construction. The investigated fibers included propylene synthetic fibers, hooked steel fibers, double and triple hooked steel fibers, hybrid crimped steel fiber and polypropylene multifilament fibers, and micro-macro steel fibers. The fiber volume varied between 0 and 0.75%. An expansive agent (EA) was incorporated to compensate for shrinkage and induce compression in the concrete at early age. Two types of EA (G and K) were employed at 0 to 8%, by mass of binder. The investigated FRSCC and …

Analysis Of Standardized Concrete Mixes, Riley Graybeal

Williams Honors College, Honors Research Projects

Concrete is one of the most common materials used in construction. It is mass produced throughout the country, with numerous different designs for concrete mixes. A common practice among concrete manufacturers is to use a standardized concrete mix design. These standardized mix designs are pre-tested and are not usually altered frequently. The hypothesis of this research project is that manufacturers do not constantly investigate new ways to save on their mixes, and simply use the same standardized mix designs.

In this research, investigations into what alterations may reduce the cost of standardized mixes began with a baseline mix design provided …

Incorporation Of Contaminated Sediment Into Environmentally Safe Concrete, Andrew Needs

Williams Honors College, Honors Research Projects

The research performed through this project provided some interesting results on how the different properties of the contaminated sediment can impact the strength of the new concrete.

Average three, seven, and fourteen-day strengths increased when comparing to the baseline mix developed for the experiment. Increases in strengths were notices in the ten and twenty-five percent soil replacement mixes. The largest increase was approximately thirty-three percent greater than the baseline average.

The results from the forty percent replacement test showed a significant decrease in strengths when comparing against the baseline mix. A loss of about thirty percent was observed between the …

On The Development Of 8,000 Psi Geopolymer Mortar For Practical Use In Field Applications, Remington Gabriel Reed

Graduate Theses and Dissertations

Although there are several perceived benefits from the use of geopolymer binder as an alternative to ordinary portland cement in concrete materials, it is not widely used in field applications. Geopolymer materials have no set guidelines for mixture design and often require heat curing to facilitate strength gain. Additionally, many geopolymers are created using carefully controlled and high quality materials and activator chemicals. These factors greatly affect the practicality of the material. The goal of this research was to create a geopolymer material capable of achieving high compressive strengths at 28 days without heat curing, and using only readily available …

Effect Of Cement Content On Concrete Performance, Caleb Joshua Lebow

Graduate Theses and Dissertations

Of all the traditional concrete materials, portland cement has the greatest impact on mixture cost and the environment. Cement is in many ways the glue holding concrete together (Weiss, 1999), and as such, it plays a major role in fresh and hardened concrete properties. Without the proper range of cement in the mixture, low strength development or excessive shrinkage may occur leading to premature deterioration. The Arkansas Department of Transportation (ARDOT) recognizes two types of concrete for use in bridge construction, Class S and Class S(AE). This paper focuses on the findings from testing of Class S(AE) concrete, short for …

State-Based Peridynamic Particle Method, Siavash Nikravesh Kazeroni

Civil Engineering ETDs

In this study, a novel discrete Peridynamics framework called the “State-Based Peridynamic Particle Model (SPPM)” is introduced. In this approach, a solid body is simulated by neither solving differential equations nor integral equations; instead, the simulation is accomplished by directly solving discrete systems of equations using finite summations. SPPM is formulated for a random distribution of particles, hence, it can be considered as a meshfree method. The assumptions of continuity and homogeneity are not necessary for this approach. The SPPM is a generalization of the “State-Based Peridynamic Lattice Model (SPLM)”. In the SPLM formulation, for sake of simplicity and computational …

Development Of High Early-Strength Concrete For Accelerated Bridge Construction Closure Pour Connections, Stephanie Castine

Masters Theses

Accelerated bridge construction (ABC) has become a popular alternative to using traditional construction techniques in new bridge construction and existing bridge deck replacement because of the reduction of time spent in field activities. A key feature of bridges built using ABC techniques is the extensive use of prefabricated components. Prefabricated components are joined in the field using small volume closure pours involving high performance materials (steel and concrete) to ensure adequate transfer of forces between components. To date, the materials developed for closure pours have been based on proprietary components, so a need has arisen for development of mixes that …

Shrinkage Cracking In Concrete Tilt-Up Construction, Stewart Hooks, Jack Robinson

Architectural Engineering

The purpose of this project is to investigate a particular, undesirable cracking pattern in concrete tilt-up panels that, until now, did not have a known definite cause. The cause of this cracking pattern is hypothesized to be due to shrinkage restraint of the concrete panels. The cracking under investigation occurs at the bottom corners of the Tilt-Up panels, suggesting that the base of the panel is restrained from shrinkage. This project models various components of Tilt-Up Construction that have potential for restraining the panels from shrinking. This project consists of the following main components.

The first aspect of this project …

Evaluating The Bond Behavior Between Frp And Grooved Concrete Specimens Using Single Shear Pull Out Test, John Omboko

Master's Theses (2009 -)

Surface preparation affects the bond behavior between Fiber Reinforcing Polymer (FRP) composite material and concrete. In this research, a special type of surface preparation known as grooving, which involves cutting transverse grooves, is conducted on concrete blocks (specimens) that are categorized as either Unfilled (U) or Filled (F). This idea is to ascertain how the grooves affect the strength of FRP-bonded-concrete specimen. These two categories are then benchmarked to control (C) specimens which do not have grooves on them. Category U specimens only have the epoxy applied on the concrete surface while category F specimens have epoxy applied on both …

Identifying Damage, Predicting Expansion, And Determining The Effectiveness Of Sealers On Concrete Affected By Alkali-Silica Reaction And Freeze-Thaw, Matthew Caleb Waidner

Graduate Theses and Dissertations

Premature cracking of the barrier wall and pavement on I-49 south of Fayetteville, Arkansas due to a combination of Alkali-Silica Reaction (ASR) and freeze-thaw has led to ASR and freeze-thaw research at the University of Arkansas. Potential for further expansion (PFET), Damage Rating Index (DRI), and mitigation of freeze-thaw and ASR with sealers testing and results are contained herein. PFET results indicated that the pavement will not continue to expand from ASR. With other interstate pavements deteriorating prematurely throughout Arkansas, DRI has shown that most are damaged not only by ASR but by freeze-thaw too. Recommendations for freeze-thaw’s inclusion into …