Engineering Commons^™

On The Development Of 8,000 Psi Geopolymer Mortar For Practical Use In Field Applications, Remington Gabriel Reed

Graduate Theses and Dissertations

Although there are several perceived benefits from the use of geopolymer binder as an alternative to ordinary portland cement in concrete materials, it is not widely used in field applications. Geopolymer materials have no set guidelines for mixture design and often require heat curing to facilitate strength gain. Additionally, many geopolymers are created using carefully controlled and high quality materials and activator chemicals. These factors greatly affect the practicality of the material. The goal of this research was to create a geopolymer material capable of achieving high compressive strengths at 28 days without heat curing, and using only readily available …

Developing Ultra-High Performance Concrete (Uhpc) With Locally Available Materials, Ali Alsalman

Graduate Theses and Dissertations

Ultra-High Performance Concrete (UHPC) can enhance the durability and resilience of concrete structures. The use of local materials is a fundamental step to save energy and reduce the cost of concrete. The main focus of this research was to develop a UHPC with compressive strength of 150 MPa using locally sources materials. In this study, the effect of fine materials, binder type and content, type of mixer, steel fibers and curing regimes on concrete’s compressive strength were investigated. The relationship between compressive strength and elastic modulus was also studied. This study synthesizes all relevant experimental data in the literature to …

Effect Of Continuity Plate Eccentricity On The Performance Of Welded Beam-To-Column Connections, Jason Thomas Norwood

Graduate Theses and Dissertations

Beam-to-column connections in structural steel buildings may have varying degrees of rotational restraint and varying degrees of moment transfer. In fully restrained moment connections, shear is typically transferred through the beam web, while the moment is mostly transferred through the beam flanges which create tension/compression force couples. Column sections that are incapable of resisting these flange forces are often retrofitted with continuity plates within the connection region to improve capacity. In cases of unequal beam depths on either side of the column, an eccentricity between the framed-in beam flange and continuity plate may be required; however, limited research exists to …

Towards Environmentally Sustainable And Cost-Effective Food Distribution In The U.S., Jasmina Burek

Graduate Theses and Dissertations

Distribution centers (DCs) and supermarkets have an important role in food sustainability, but no previous research has accounted for their environmental impact. The purpose of this research was to assess environmental sustainability of grocery, perishables, and general merchandise DCs; to estimate food storing and retailing impact; and to provide cost-effective strategies to reduce DCs’ environmental impacts. The importance and relevance of the research is threefold: improving sustainability of DCs, food storing, and food retailing. The main method used in this research was the life cycle assessment (LCA) method. An initial study calculated environmental impacts of the Wal-Mart Stores, Inc. DCs, …

Utilizing The Hvsr Second Peak For Surface Wave Inversions In The Mississippi Embayment, Ashraf Kamal Himel

Graduate Theses and Dissertations

Ambient noise data from 24 sites within the Mississippi Embayment were analyzed to estimate the fundamental frequency using the horizontal to vertical spectral ratio (HVSR) method. The fundamental frequency ranged from 0.17 to 3.43 Hz for the tested sites. At seventeen of the sites, a second higher frequency HVSR peak, which ranged from 0.617 Hz to 2.154 Hz, was observed in addition to the fundamental HVSR peak. The second peak frequency in the HVSR curve has been attributed by previous researchers as either an odd harmonic of the fundamental peak or a shallow impedance contrast from the Memphis sand layer …

Development Of Anti-Icing Airfield Heated Pavement Systems Using Solar Energy, Joseph Daniels

Graduate Theses and Dissertations

This dissertation analyzes developing and assessing the viability of an anti-icing airfield heated pavement system using solar energy. This study includes two components, a field experimentation component and a numerical analysis component. Field experimentation investigates two systems: (1) an electrical heated pavement system with a photovoltaic energy system as its power source, and (2) a hydronic heated pavement system with a solar water-heating system as its heating source. The systems operate under an automated thermostat heating sequence for operation optimization and energy conservation. Study results found the solar systems capable of supplying enough energy to maintain pavement surface temperature above …

Effect Of Cement Content On Concrete Performance, Caleb Joshua Lebow

Graduate Theses and Dissertations

Of all the traditional concrete materials, portland cement has the greatest impact on mixture cost and the environment. Cement is in many ways the glue holding concrete together (Weiss, 1999), and as such, it plays a major role in fresh and hardened concrete properties. Without the proper range of cement in the mixture, low strength development or excessive shrinkage may occur leading to premature deterioration. The Arkansas Department of Transportation (ARDOT) recognizes two types of concrete for use in bridge construction, Class S and Class S(AE). This paper focuses on the findings from testing of Class S(AE) concrete, short for …

Early Life Flexural Performance And Behavior Of Reinforced Bcsa Concrete Beams, Gabriel Cook

Graduate Theses and Dissertations

Belitic calcium sulfoaluminate cement (BCSA) is a hydraulic, rapid setting alternative to ordinary portland cement (OPC) with reduced energy demands and CO2 emissions. BCSA cement has numerous current and potential applications including transportation repair and precast manufacturing. Currently, limited research exists regarding the structural performance of CSA cements, restricting its potential implementation. Thus, the purpose of this research is to provide insight into the flexural performance and behavior of reinforced BCSA concrete beams. Overall, BCSA concrete had similar cracking and loading behavior to the OPC beams, with increased moment capacity for compression controlled specimens. Furthermore, BCSA concrete showed increased tensile …

Interfacial Tailoring Of Lithium-Ion Batteries By Atomic/Molecular Layer Deposition, Qian Sun

Graduate Theses and Dissertations

Lithium-ion batteries (LIBs) are promising energy storage devices, which play significant roles in addressing problems related to fossil fuels depletion and environmental pollution. Since the 1990s, LIBs have attracted great attention for many applications. Nowadays, LIBs are dominating portable electronics, having several advantages over their forerunners, such as high voltage (3.3~4.2 V) [1,2], low self-discharge (< 5~10 %/month) [3,4], wide operation temperature (-20~60 °C) [5,6], and fast charge/discharge rate [7,8]. However, LIBs deliver an energy density of 100-220 Wh/kg in practice to date, which is far from their theoretical ones, thus hindering their further applications in electric vehicles. Additionally, LIBs have been plagued by other problems, such as intolerance to overcharge/overdischarge, low heat resistance, lithium dendrites growth, large volume change of the silicon anode, large polarization and even safety problems.

Atomic layer deposition (ALD) and molecular layer deposition (MLD) are two important techniques, both proceeding in self-limiting gas-solid reactions and exhibiting excellent capabilities for ultra-thin films, conformal coatings, and controllable growth. They can be employed to address the problems of LIBs mentioned above by …

Examining The Use Of Idealized Granular Material In Validated Dem Simulations, Anjana Thoroppady Kittu

Graduate Theses and Dissertations

Discrete element method (DEM) modeling, is becoming widely used for understanding the micro-mechanical behavior of granular materials at the particle level. This dissertation presents important considerations regarding the experimental boundary conditions and idealized granular materials used in DEM validations.

A common issue in DEM validation studies for direct shear and direct simple shear is selecting top and bottom cap boundary conditions that allow for shear transmission while also being efficiently modeled in the DEM simulations. While the traditional grid boundary types used in the laboratory can be replicated in the numerical models, researchers have also used fixed-particle boundaries, sawtooth boundaries, …

A Generative Statistical Approach For Data Classification In A Biologically Inspired Design Tool, Marvin Manuel Arroyo Rujano

Graduate Theses and Dissertations

The objective of the research this thesis describes is to find a way to classify text-based descriptions of biological adaption to support Biologically Inspired design. Biologically inspired design is a fairly new field with ongoing research. There are different tools to assist designers and biologists in bio-inspired design. Some of the most common are BioTRIZ and AskNature. In recent years, more tools have been proposed to aid and make research in the field easier, for example, the Biologically Inspired Adaptive System Design (BIASD) tool. This tool was designed with the goal of helping designers in early design stages generate more …

Fatigue Performance And Shear Demand Distributions Of Clustered Shear Connectors In Composite Bridge Girders, Brian David Hillhouse

Graduate Theses and Dissertations

The current American Association of State Highway and Transportation Officials (AASHTO) Bridge Specifications assumes uniform shear flow demands at the steel-concrete interface of composite bridge girders. As stud pitch increases to beyond 24 in or as studs become clustered to account for pre-cast concrete decks, this assumed shear demand distribution may be unrepresentative. Understanding shear transfer and resulting demands on headed studs in composite beams are important for ensuring adequate composite design. This study investigates stud demands in composite bridge girders using large-scale fatigue testing and direct pressure measurements for stud force calculations. In this study, two large-scale composite beam …

Accumulation Of Lead By Biofilms In Drinking Water Distribution Systems, Kaleb Oren Belcher

Graduate Theses and Dissertations

Recent crises, such as the one in Flint, MI, indicate that lead exposure from drinking water is a major health concern in the United States. Over six million lead service lines are still in use in the United States, and a universal protocol to safely remove these lead service lines from drinking water distribution systems has not yet been established. This paper calls to attention the potential hazard that biofilms pose as a source of lead in distribution systems, even after the removal of lead pipes. This study used a simulated water distribution system containing a lead source pipe and …

The Effect Of Incorporating End-User Customization Into Additive Manufacturing Designs, Jonathan D. Ashley

Graduate Theses and Dissertations

In the realm of additive manufacturing there is an increasing trend among makers to create designs that allow for end-users to alter them prior to printing an artifact. Online design repositories have tools that facilitate the creation of such artifacts. There are currently no rules for how to create a good customizable design or a way to measure the degree of customization within a design. This work defines three types of customizations found in additive manufacturing and presents three metrics to measure the degree of customization within designs based on the three types of customization. The goal of this work …

Development Of A Rapid Fatigue Life Testing Method For Reliability Assessment Of Flip-Chip Solder Interconnects, Cody Jackson Marbut

Graduate Theses and Dissertations

The underlying physics of failure are critical in assessing the long term reliability of power packages in their intended field applications, yet traditional reliability determination methods are largely inadequate when considering thermomechanical failures. With current reliability determination methods, long test durations, high costs, and a conglomerate of concurrent reliability degrading threat factors make effective understanding of device reliability difficult and expensive. In this work, an alternative reliability testing apparatus and associated protocol was developed to address these concerns; targeting rapid testing times with minimal cost while preserving fatigue life prediction accuracy. Two test stands were fabricated to evaluate device reliability …

Developing Computer Codes For Analyzing Bridge Response Due To Wim Data Truck Loading, Kenneth Patrick Pasley

Graduate Theses and Dissertations

Despite actual truck demographics evolving over the past 30 years, the Arkansas legal loads for bridge posting have not been updated. Custom computer codes were developed.to facilitate comparison between the current Arkansas legal loads for bridge posting and the actual Arkansas truck traffic to ensure that actual reactions are enveloped by the state'. The program, WIMFluence, calculates shear and moment influence lines for a bridge and the resulting shear and moment reactions based on weigh-in-motion data. With supporting scripts, the reactions due to actual Arkansas truck traffic were compared to those due to the current Arkansas legal loads for bridge …

Assessing Biofiltration Without Ozonation For Removal Of Trihalomethane Precursors In Drinking Water At The Beaver Water District Drinking Water Treatment Plant, Sana Ajaz

Graduate Theses and Dissertations

Biofiltration without pre-ozonation has the capability to remove natural organic matter (NOM) fractions that serve as precursors of disinfection byproducts (DBPs), which include the four regulated trihalomethanes (THMs) and dichloroacetonitrile (DCAN). Rapid small-scale column tests (RSSCTs) and Pilot Plant filters operated at empty-bed contact times (EBCTs) of 4, 8, and 16 minutes were used to evaluate the performance of nutrient-amended (free ammonia and phosphorus) biofiltration for THM and DCAN precursor removal, as measured using formation potential (FP) tests. NOM surrogates – which include dissolved organic carbon (DOC), specific ultraviolet absorbance (SUVA254) and fluorescence-PARAFAC components – were measured weekly throughout the …

Exploring Photo Privacy Protection On Smartphones, David Darling

Computer Science and Computer Engineering Undergraduate Honors Theses

The proliferation of modern smartphone camera use in the past decade has resulted in unprecedented numbers of personal photos being taken and stored on popular devices. However, it has also caused privacy concerns. These photos sometimes contain potentially harmful information if they were to be leaked such as the personally identifiable information found on ID cards or in legal documents. With current security measures on iOS and Android phones, it is possible for 3rd party apps downloaded from official app stores or other locations to access the photo libraries on these devices without user knowledge or consent. Additionally, the prevalence …

Controlling Relative Humidity Using Glycerin, Juan Martinez

Civil Engineering Undergraduate Honors Theses

A series of tests were conducted to control relative humidity (RH) using a bubbler system that contained a series of glass jars and glass vials filled with different concentrations of glycerin. The relative humidity within the glass jars was measured. The total time interval for each laboratory test was 48 hours. During the first 24 hours a pump was used to bubble air through the glycerin solution. During the second 24 hours, the pump was turned off, and the RH within the system was monitored within the closed system. Target RH measurements from 100% to a 0% were obtained. The …

Optimizing The Plasmonic Enhancement Of Light In Metallic Nanogap Structures For Surface-Enhanced Raman Spectroscopy, Stephen Joseph Bauman

Graduate Theses and Dissertations

Technology based on the interaction between light and matter has entered something of a renaissance over the past few decades due to improved control over the creation of nanoscale patterns. Tunable nanofabrication has benefitted optical sensing, by which light is used to detect the presence or quantity of various substances. Through methods such as Raman spectroscopy, the optical spectra of solid, liquid, or gaseous samples act as fingerprints which help identify a single type of molecule amongst a background of potentially many other chemicals. This technique therefore offers great benefit to applications such as biomedical sensors, airport security, industrial waste …

Exfoliation, Synthesis, And Characterization Of Nanoscale Te, Takayuki Hironaka

Graduate Theses and Dissertations

Since the experimental discovery of graphene, two dimensional materials have enjoyed more attention and emphasis in academic research than nanowires, but the latter are an important area of study for creating 1D materials, or single atom chains, the next generation materials for advancing electronic devices. Atomically thin layers can be generated from 2D materials with weak bonds in one direction, and by applying this concept to one dimensional weakly bonded materials, we hypothesize that single atom chains with atomic-scale diameters may be produced. Tellurium (Te) and selenium (Se) have lattices consisting of spiral chains oriented along the c-axis, and each …

Fingerprint Database Privacy Guard: An Open-Source System That Secures Fingerprints With Locality Sensitive Hashing Algorithms, Enrique Sanchez

Computer Science and Computer Engineering Undergraduate Honors Theses

Fingerprint identification is one of the most accurate sources of identification, yet it is not widely used in public facilities for security concerns. Moreover, the cost of fingerprint system is inaccessible for small-budget business because of their high cost. Therefore, this study created an open-source solution to secure fingerprint samples in the database while using low-cost hardware components. Locality Sensitive Hashing Algorithms such as ORB and Image hash were compared in this study as a potential alternative to SURF. To test the design, fifteen samples were collected and stored in a database without verifying the quality of the samples. Then, …

Impedance Sensing Of Cancer Cells Directly On Sensory Bioscaffolds Of Bioceramics Nanofibers, Hanan Alismail

Graduate Theses and Dissertations

Cancer cell research has been growing for decades. In the field of cancer pathology, there is an increasing and long-unmet need to develop a new technology for low-cost, rapid, sensitive, selective, label-free (i.e. direct), simple and reliable screening, diagnosis, and monitoring of live cancer and normal cells in same shape and size from the same anatomic region. For the first time on using an impedance signal, the breast cancer and normal cells have been thus screened, diagnosed and monitored on a smart bioscaffold of entangled nanowires of bioceramics titanate grown directly on the surface of implantable Ti-metal and characterized by …

Gesn Thin Film Epitaxy And Quantum Wells For Optoelectronic Devices, Perry Christian Grant

Graduate Theses and Dissertations

Group IV photonics is an effort to generate viable infrared optoelectronic devices using group IV materials. Si-based optoelectronics have received monumental research since Si is the heart of the electronics industry propelling our data driven world. Silicon however, is an indirect material whose optical characteristics are poor compared to other III-IV semiconductors that make up the optoelectronics industry. There have been major efforts to integrate III-V materials onto Si substrates. Great progress on the integration of these III-V materials has occurred but incompatibility with CMOS processing has presented great difficulty in this process becoming a viable and cost-effective solution. Germanium …

Utilizing 3d Printed Analogue Soils To Investigate Specimen Size Effects In Triaxial Testing, Claire Louise Stewart

Graduate Theses and Dissertations

Triaxial testing is one of the fundamental laboratory tests used in geotechnical engineering to determine strength parameters, such as shear strength and friction angle. Investigating the minimum representative elementary volume (REV) can verify the independence of size effects on strength parameters and ensure that the scaled laboratory tests results are consistent, repeatable, and representative of field conditions. Although, REV has been studied for many applications, there is disagreement within geotechnical engineering of a minimum particle diameter to specimen diameter to minimize the size effects related to the REV in consolidated drained (CD) triaxial tests. This research study compared the strength …

Investigation Of A Gan-Based Power Supply Topology Utilizing Solid State Transformer For Low Power Applications, Akrem Mohamed Elrajoubi

Graduate Theses and Dissertations

Gallium nitride (GaN) power devices exhibit a much lower gate capacitance for a similar on-resistance than its silicon counterparts, making it highly desirable for high-frequency operation in switching converters, which leads to their significant benefits on power density, cost, and system volume. High-density switching converters are being realized with GaN power devices due to their high switching speeds that reduce the size of energy-storage circuit components. The purpose of this dissertation research is to investigate a new isolated GaN AC/DC switching converter based on solid-state transformer configuration with a totem-pole power factor corrector (PFC) front-end, a half-bridge series-resonant converter (SRC) …

Automatic Performance Optimization On Heterogeneous Computer Systems Using Manycore Coprocessors, Chenggang Lai

Graduate Theses and Dissertations

Emerging computer architectures and advanced computing technologies, such as Intel’s Many Integrated Core (MIC) Architecture and graphics processing units (GPU), provide a promising solution to employ parallelism for achieving high performance, scalability and low power consumption. As a result, accelerators have become a crucial part in developing supercomputers. Accelerators usually equip with different types of cores and memory. It will compel application developers to reach challenging performance goals. The added complexity has led to the development of task-based runtime systems, which allow complex computations to be expressed as task graphs, and rely on scheduling algorithms to perform load balancing between …

Smart Surge Irrigation Using Microcontroller Based Embedded Systems And Internet Of Things, Prashant Dinkar Borhade

Graduate Theses and Dissertations

Surge Irrigation is a type of furrow irrigation and one of many efficient irrigation techniques. It is one of the economical techniques and requires minimum labor for monitoring it. In surge irrigation, water is applied intermittently to a field to achieve uniform distribution of water along the furrows, which is important while irrigating, as it ensures that there is enough water near the root zone of the crop. The uneven distribution can cause a loss in crop productivity.

Surge irrigation uses a surge valve, which is an electro-mechanical device that irrigates a field. The commercial surge valves available on the …

An Rs-485 Transceiver In A Silicon Carbide Cmos Process, Maria Raquel Benavides Herrera

Graduate Theses and Dissertations

This thesis presents the design, simulation and test results of a silicon carbide (SiC) RS-485 transceiver for high temperature applications. This circuit is a building block in the design and fabrication of a digital data processing and control system. Automation processes for extreme environments, remote connection to high temperature locations, deep earth drilling, and high temperature data acquisition are some of the potential applications for such a system. The transceiver was designed and developed in a 1.2 µm SiC-CMOS process by Raytheon Systems, Ltd. (UK). It has been tested with a supply voltage of 12 V and 15 V, temperatures …

Measuring Characteristic Shrinkage Variability Due To Metal Loading Effects In Low Temperature Co-Fired Ceramic Using Image Processing, John Ezekiel Zumbro

Graduate Theses and Dissertations

Low temperature co-fired ceramic (LTCC) has many benefits when it comes to electronic packaging due to the low dielectric loss, reliability in extreme environments, and high breakdown voltage. Though the ceramic has a lot of benefits it is not widely used due to the high cost and complexities associated with manufacturing. One of these issues with manufacturing is compensating for the shrinkage of the ceramic, this is accomplished by using an expansion factor, creating the “green” or manufactured design. This expansion factor is approximated through knowledge of the ceramic factors such as the metal loading, layers of ceramic tape, firing …