Engineering Commons^™

Investigation Of Grouted Dowel Connection For Precast Concrete Wall Construction, Douglas J. Provost-Smith

Electronic Thesis and Dissertation Repository

The grouted dowel connection is a simple and cost-effective connection used in many precast concrete structural systems. The required dowel length is currently designed as a regular bar in reinforced concrete, which underestimates the bond strength, thus resulting in excessive connection lengths. Furthermore, precast wall construction continues throughout cold weather, where in-situ heating of the grout used in the grouted dowel connections is usually conducted for short periods of time. Hence, early-age exposure to subfreezing conditions may affect the quality of the grout and subsequently the bond strength of the connection, which can compromise structural integrity.

In this thesis, full-scale …

The Impact Of Project Delivery Methods On Dispute Occurrence In Public Highway Projects, Samaneh Nasrollahi, Ghada M. Gad, Alan Atalah

Master of Technology Management Plan II Graduate Projects

The construction industry is a complex and competitive industry in which different participants with different expertise, talents, and levels of knowledge work together to achieve their objectives and complete a project. Sine different participants with different interest involve in a construction project, therefore, conflicts arise and become inevitable. Conflicts in projects will cause an adversarial environment which result to disputes. Hence, if conflicts are not well managed and resolved in a timely manner, they quickly turn into disputes, which prevent the successful completion of the construction project, in terms of cost and time, and increasing the potential for poor project …

I-94 Advanced Bridge Replacement, Saleem Alsharari

Honors Theses

The Michigan Department of Transportation has always felt the need of improving and increasing the capacity of the most critical highway in the state of Michigan, I-94. Part of the improvement plan is to increase the capacity of a 6-mile segment along a corridor of I-94 from French Avenue to Trumbull Avenue which is in a suburban neighborhood of Detroit. There are eight bridges built in the 1950’s that need to be re-constructed for a capacity increase. Vehicular and non-motorized traffic must be accounted for in the design of these bridges. The project is intended to increase the service life …

Safety Benefit Analysis Of Alternative Delineation Practices In Michigan, Brenda C. Burdick

Masters Theses

Among the many aspects of roadway design, one important system is roadway delineation. The main purposes of roadway delineation include regulating, warning, and guiding drivers in a safe manner. Delineation systems have the potential to reduce crashes. This research sought to perform safety benefit analysis of roadway delineation practices in Michigan. Through literature review, several delineation practices, selection criteria, and previously developed crash modification factors were researched. Even though several pavement marking materials have been implemented in Michigan, a safety benefit analysis of various materials had not been performed. Sites were selected, and pavement marking material inventory data were combined …

Analysis Of Transit Accessibility For People With Disabilities, Rostam Khalid Mohammed Ameen Qatra

Masters Theses

The inconvenience of public transit systems and unavailability of bus stops in the United States has resulted in a heavy reliance on the private automobile. One of the main issues in transit services is accessibility, particularly for people with disabilities. This research is intended to compare estimated job accessibility measures by transit in Kalamazoo county for workers with reduced physical mobility and without. Using OpenTripPlanner (OTP) software, General Transit Feed Specification (GTFS), Open Street Map (OSM) and Longitudinal Employer-Housing Dynamics (LODES) data were analyzed to estimate job accessibility for people with mobility constraints. By using the shortest tree path method, …

Feasibility Study Of Using Recyclable Polyethylene (Pet) Materials As Coarse Aggregate For Concrete Mixtures, Philip M. Angelo

Construction Management

The feasibility of using recyclable household plastics, specifically those made of polyethylene, commonly used in water and soda bottles, as a replacement for concrete coarse aggregate, was assessed. A method was developed for cutting polyethylene materials into fibrous strips. These strips were then used as a replacement for the rock coarse aggregate in batches of concrete. Standard 6” x 12” test cylinders were made using the concrete mixture and subject to destructive compressive testing in order to yield the compressive strength of the concrete mix 7, 14, 21, and 28 days after pouring. Three mixtures were tested, one control with …

Carpenters Apprenticeship Internship: Student And Industry Perspectives, Chris Falco

Construction Management

The Carpenters Apprenticeship Internship program is designed to provide students the opportunity to work as a construction laborer and get hands-on work experience. The goal of this study is to address the perceived benefits of the Carpenters Apprenticeship Internship with respect to the students, the industry members, and the union. In looking at the benefits this opportunity presents, any value that is aligned among the parties involved will be highlighted to convey the mutual advantages. Lastly, the demand among students for experience such as this will be assessed to see what the perceived value of labor experience is among students …

Technology Adoption By California Central Coast Contractors, Nicholas A. English

Construction Management

Technology is trending in Construction, but it is unclear if smaller contractors have kept up with these trends like larger national companies have. This survey of San Luis Obispo County specialty and general contractors queried technology adoption, specific software use, estimator age, and opinions of various estimating attributes. It found that the majority of contractors use traditional estimating and quantity takeoff methods, the majority of contractors are 31 years old or older, and that local estimators value experience and knowledge as opposed to computer expertise. Local contractors recognize the value technology can provide, but have not adopted it in a …

Construction Of A Chicken Coop For Use By An Early Education Facility, Luke Cypress

Construction Management

There is a demand in the early education field for methods of exposing early learners to where our food comes from and how it’s produced. An excellent source of this exposure is commonly utilized in an onsite chicken-coop. These coops are in essence working farms, producing eggs and in some cases meat. While coops are not prohibitively expensive they often fall outside the scope of normal operating or educational budgets and can be difficult to fund. The purpose of this project was to identify a school that could use and benefit from a coop at no cost to the school. …

Photovoltaic Installation In Ecuador And The Amazon, David Mulder

Construction Management

The Photovoltaic Installation in Ecuador and The Amazon is part of a collaborative effort between two major construction clubs at Cal Poly: NECA and MCAA. Four students, two from each club, traveled with two faculty to install photovoltaics for two different communities. The first project was a solar installation to provide fresh water for the community of Santa Rosa. Project number two, was a sixteen-panel installation in Shell, Ecuador for the non-profit Reach Beyond. The main goals of each project were to provide fresh water, and achieve net zero electrical consumption.

A Case Study On Achieving 100% Customer Satisfactory Homes In Production Home Building, Garrett Whitlock

Construction Management

No abstract provided.

Outsourcing Of Building Information Modeling (Bim) Among General Contractors In The United States, James W. Fountain

Honors Theses

Building Information Modeling (BIM) is a process used by AEC industry members that simulates a construction project in a multidimensional digital model and provides multitudes of project benefits from inception to occupancy. However, a variety of barriers impede a holistic BIM implementation. Because of these barriers, some general contractors are choosing to outsource the creation and/or utilization of BIM models to specialized Information Technology (IT) firms instead of performing these processes in-house. Since little literature currently exists for BIM outsourcing, this online survey-based study aimed to identify BIM outsourcing patterns among the general contractors across the US and the perceived …

Kihefo Vocational Center: Kabale, Uganda, Jason Matthew Angerer

Construction Management

Journeyman International (JI) is a non-profit organization which acts as a platform for bringing together volunteer Architects, Designers, Engineers, and Construction Managers with humanitarian projects around the world. Kigezi Healthcare Foundation (KIHEFO) a non-profit NGO located in Kabale, Uganda is a client seeking to build a vocational center to educate the workforce of Uganda. The center will include multi-purpose class rooms, a dining hall, rabbit farm, carpentry shop, and living complex. The Architect on the project was Courtney Wedel from Cal Poly. As the Construction Manager on the project my responsibilities include; Design Assist, Feasibility Analysis, Scheduling, Estimating, and Managing …

Characterization And Delineation Of Karst Geohazards Along Rm652 Using Electrical Resistivity Tomography, Culberson County, Texas, Adam F. Majzoub

Electronic Theses and Dissertations

The Delaware Basin of West Texas and southeastern New Mexico is the major western subdivision of the Permian Basin and a northern extension of the Chihuahuan Desert. The major evaporite unit within the Delaware Basin is the Castile Formation, which consists of gypsum/anhydrite and is highly susceptible to dissolution and karsting. Manifestations of karst within the Castile outcrop are abundant and include sinkholes, subsidence features and caves, both epigene and hypogene in origin.

Land reconnaissance surveys conducted during the summer of 2015 documented abundant karst landforms in close proximity to a major thoroughfare, RM 652, in Culberson County, Texas. 2D …

Integrated Urban Metabolism Analysis Tool (Iumat), Nariman Mostafavi

Doctoral Dissertations

A number of tools are available today for simulating different aspects of urban activity, but these efforts are fragmented and do not effectively reflect the interrelationships between very diverse groups of urban sectors and resource flows. There is a critical need for robust and reliable urban metabolism analysis tools that integrate socio-economic elements of urbanization and physicality of the built environment into evaluating sustainability in cities. This dissertation outlines the development of an Integrated Urban Metabolism Analysis Tool (IUMAT) that dynamically measures the environmental impacts of land cover, transportation, and consumption of energy, water and materials employing a holistic framework. …

High-Level Multi-Objective Model For Microgrid Design, Siamak Talebi

Theses and Dissertations

Recently, there is vast inclination toward using renewable energy in rural areas away from the main electricity generation plants. Small airports located in rural areas are good candidates to apply sustainable energy for electrical power needs. Because of the intermittency of the renewable sources, it is important to have energy storage to guarantee an uninterrupted and stable power supply for end users. In this work, a high-level micro grid model is proposed considering making decisions about different factors such as different renewable sources capacity, storage and system capacity. A multi-objective model of a microgrid high-level design is used to formulate …

Modeling Atypical Building Use With Commercially Available Building Simulation Software, Sarah E. Schanck

Theses and Dissertations

National Guard armories are audited to provide recommendations for future energy reduction measures. The annual energy consumption of a New Jersey National Guard Armories cannot be modeled directly with commercially available building simulation software, due to discrepancies between the modeling capabilities of the software and the reality of the armory. A building simulation software, eQUEST, was chosen for use in this project. Discrepancies between eQUEST inputs and reality were identified and correction factors developed to minimize the effect of each discrepancy on predicted energy consumption, with the end goal of accuracy between predicted and actual energy consumption. In addition, an …

Engineered Earthen Masonry Structures For Extreme Wind Loads, Mabel Cristina Cuellar-Azcarate

Theses and Dissertations

Stabilized earthen masonry (SEM), which is built with compressed stabilized earthen blocks (CSEB) and mortar, is emerging as a construction system for affordable, sustainable and high-quality dwellings. Compelling features of earthen masonry are local availability of suitable soils, thermal insulation properties, humidity control within healthy ranges, and relatively low carbon footprint. SEM is also appealing for the construction of affordable houses in rural areas and farmlands, where underrepresented and underprivileged groups often live. In fact, the lack of affordable housing is an issue across the United States where low-income families are most affected, often committing more than half of their …

An Investigation In Construction Cost Estimation Using A Monte Carlo Simulation, Jeffrey D. Buchholtz

Theses and Dissertations

The Air Force estimates military construction (MILCON) costs early in a project’s development as a part of the funding approval process. However, many of the initial cost estimates deviate significantly more than expected from the actual project costs, hindering funding allocation efforts. There is a need for improved estimation techniques. This research examines a cost estimation model for the initial programming stages of a project when only general scope information is available.

This study develops a Monte Carlo simulation based on historical construction cost data to predict project costs base on facility type. For a given facility type, the research …

Comparison Of Safety And Operational Performances For Three Engineering Countermeasures, Ali Hamzah Hussein Alzuhairi

Masters Theses

While there have been many studies on engineering treatments for reducing traffic crashes or for improving intersection efficiency, few studies have been simultaneously taking both impacts into consideration. This thesis analyzed impacts of engineering countermeasures and determines when these countermeasures are cost effective with respect to the amount of traffic and the number of crashes. Both crash reduction and operational costs were compared for analysis. This study specifically investigated three countermeasures: changing from permitted to protected for a left-turn on minor approaches, leading pedestrian interval (LPI), and exclusive pedestrian phase (Barnes Dance). The general Safety Performance Functions (SPFs) from the …

Verifying Automated Prestressed Concrete Design Software For Mdot Bridge Design Standards, Hussein Kadhim Abood Khalaf

Masters Theses

The design and analysis of bridges is a very critical and time consuming process. The automation of bridges design can save us time and effort, but the designer must have enough background with structural design of bridges in order to be able to analyze and understand the output of the automated design. This research shows the design and analysis of the superstructure of the US-27 Interchange Bridge at M-57 in Gratiot County of Washington Township, Michigan. The main purpose of this research is to establish a comprehensive design example following AAHTO LRFD Bridge Design Specifications and Michigan Bridge Design Manual. …

Agent-Based Modeling Of Abc Methods For Decision-Making In Highway Bridge Projects Including Uncertainty And Several Stakeholders, Abdul Wahed Mohammed

Dissertations

Accelerated Bridge Construction (ABC) methods that were recently introduced in the U.S. to reduce the on-site construction duration furnish several benefits to the public and highway agencies. Further, the traffic growth in addition to increasing number of functionally obsolete and structurally deficient bridges necessitates the increased implementation of ABC methods. In recent years, several Departments of Transportation (DOTs) in the U.S. have developed decision-making models to compare broadly ABC to conventional bridge construction for a particular site. However, with increased implementation and advancements in ABC methods, there is a need for specifying a particular ABC method and a superstructure system …

An Investigation Of The Impact A Rov Competition Curriculum Has On Student Interest In Stem, Specifically Technology And Engineering, Daniel Gordon Bates

Theses and Dissertations

This research investigates the impact a Remotely Operated Vehicle (ROV) program has on student interest in, and perception of, technology and engineering (sTEm). ROV programs embed areas of science, technology, engineering and math (STEM) into their curriculum; however, emphasis for this study is placed on interest and perception of the "T" and "E" of STEM. Although there are many articles detailing the benefits of ROV programs, there is little empirical data documenting the impact on student interest and perception of sTEm. This study outlines the background of a few major ROV programs in the U.S.; specifically Utah Underwater Robotics (UUR), …

Pervious Pavement Systems For High Traffic Roadways, Kevin M. Smith

Construction Management

This report highlights the benefits and detriments of pervious pavement systems through research of existing knowledge and multifaceted experiments to determine the feasibility of implementing a pervious pavement system on high traffic roadways. With over 40,000 miles of highway in the United States alone and severe water crises in states like California and growing environmental and safety concerns, the need for pervious pavements is abundantly clear. The research conducted utilizes existing knowledge on pervious pavements and applies it to the application of high traffic roadways. The experiment tests four different pervious concrete mix designs to determine compressive strength and water …

Comparison Of Energy Analysis Platforms For Title 24compliance, Holli L. Tripp

Construction Management

The 2013 Building Energy Efficiency Standards for Low-Rise Residential Buildings allow users to demonstrate compliance via two methods: performance or prescriptive. Prescriptive documentation requires analysis to be conducted by-hand while performance compliance utilizes computer modeling software to analyze trade-offs, and demonstrate compliance through alternative building design parameters. Typically computer demonstrated compliance via the performance method is the most popular choice because it allows for complex buildings to be analyzed using their actual metrics which results in a more accurate report of proposed energy consumption (Ross, 2016). This method however requires additional software outside of the tools that architects and designers …

Integrating Bim To The Construction Industry: The Hardships, Benefits, And An Unyielding Educational Gap Between Technology And Field Application, Torrie Peth

Construction Management

In recent years, Building Information Modeling has taken the construction industry by storm and revolutionized the construction process entirely. It allows for trades to coordinate more efficiently and effectively, while providing a hands-on, 3D overview of a structure being built. Certain characteristics are more easily adoptable by existing companies than others, but there are vast "fallacies of hype" in the concept. This study will examine the effects as BIM, positive and negative, and its current usage in industry. In addition it will identify the gap developing between students exiting the university setting that has a strong emphasis on technological integration, …

Friction Bit Joining Of Dissimilar Combinations Of Gadp 1180 Steel And Aa 7085 – T76 Aluminum, Lorne Steele Atwood

Theses and Dissertations

Friction Bit Joining (FBJ) is a method used to join lightweight metals to advanced high-strength steels (AHSS). The automotive industry is experiencing pressure to improve fuel efficiency in their vehicles. The use of AHSS and aluminum will reduce vehicle weight which will assist in reducing fuel consumption. Previous research achieved joint strengths well above that which was required in three out of the four standard joint strength tests using DP980 AHSS and 7075 aluminum. The joints were mechanically tested and passed the lap-shear tension, cross-tension, and fatigue cycling tests. The t-peel test configuration never passed the minimum requirements. The purpose …

Cost Effective Manhole To Pipe Connection, Utkarsh Shekhar

Master of Technology Management Plan II Graduate Projects

The manhole to the pipe connection is an important part of the sewer system. Any problem in the seal connecting the manhole to the pipe results into either inflow of ground water into the sewer system or outflow into the surrounding environment. The inflow of ground water on one hand increases the volume of wastewater being sent to the wastewater plant and on the other hand, the outflow leads to the contamination of the surrounding soil. Hence, the durability and longevity of the manhole to the pipe connection is crucial.

The manhole to the pipe connection generally fails due to …

Structural Identification Of An Elevated Water Tower, James Thomas Norris

Graduate Theses and Dissertations

Elevated water tanks are generally located at higher elevations within a particular geographic area. The location and height of these structures often makes them desirable for installing wireless and cellular communications antennas. The impact of this practice on the long-term serviceability performance of the primary structure is not clear and could be an important consideration deserving further analysis. This paper presents a case study of an elevated water tank that was motivated by this particular consideration. The structure had been retrofitted with cellular antennas during its service and later experienced fatigue cracking at the fill pipe-tank interface. The owner wished …

Sidewalk Infrastructure Improvements Design For Calhoun, Tn, Bailee Young, Mark Nichols, Trenton Smith, Brian Walker, Liam Weaver, Marquise Webb

Chancellor’s Honors Program Projects

No abstract provided.