Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Theses/Dissertations

2014

Mechanical properties

Articles 1 - 8 of 8

Full-Text Articles in Engineering

Functionalized Graphitic Nanoreinforcement For Cement Composites, Nima Zohhadi Dec 2014

Functionalized Graphitic Nanoreinforcement For Cement Composites, Nima Zohhadi

Theses and Dissertations

Physical and mechanical properties of graphitic nanomaterials, in particular multiwalled carbon nanotubes (MWCNTs) and graphene nano-platelets (GNPs) make them promising candidates for nanoreinforcement of cement composites. The two key challenges associated with the incorporation of MWCNTs and GNPs are to attain uniform dispersion and interfacial bonding within the composite matrix. The effects of three main-stream dispersion techniques (namely, ultrasonication, acid-etching, and surfactant-coating) on the mechanical properties and microstructure of MWCNT- and GNP-cement composites were experimentally studied. Compressive strength tests and different characterization techniques including dynamic light scattering, Raman spectroscopy, Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission …

Go to article

Single Fiber Mechanical Properties Using Nano-Tensile Testing And Carbon Fiber Structure-Property Relationship, Matthew Erich Kant Dec 2014

Single Fiber Mechanical Properties Using Nano-Tensile Testing And Carbon Fiber Structure-Property Relationship, Matthew Erich Kant

Doctoral Dissertations

Single carbon fibers are studied using a nano-tensile testing system. This system has unprecedented load and displacement resolution, nN and nm respectively, and the ability to perform dynamic testing for storage and loss modulus during quasi-static tensile extension. Furthermore, improved fiber mounting and alignment procedures coupled with the precision of the nano-tensile testing system assist in unprecedented resolution in single fiber mechanical testing for axial modulus and strength. Hence, using these unique capabilities, the moduli and their statistical distribution of many high performance carbon fibers are reported here. From this, a simplified single parameter model describing the strain dependent modulus …

Go to article

Patterning And Mechanical Analysis Of Fiber-Based Materials, Samuel A. Pendergraph Nov 2014

Patterning And Mechanical Analysis Of Fiber-Based Materials, Samuel A. Pendergraph

Doctoral Dissertations

The ability to define and control the topography of a surface has been studied extensively due to its importance in a wide variety of applications. The control of a non-planar topography would be very valuable since a number of structures that are pervasive in artificial applications (e.g. fibers, lenses) are curved interfaces. This potential of enabling applications that incorporate non-planar geometries was the motivation for this thesis. The first study of this thesis comprises the study of patterning the circumference of micrometer sized fibers. Specifically, a unique technique was described to pattern the fiber with a periodic array of colloids. …

Go to article

Temperature And Alloying Effects On The Mechanical Properties Of Equiatomic Fcc Solid Solution Alloys, Zhenggang Wu Aug 2014

Temperature And Alloying Effects On The Mechanical Properties Of Equiatomic Fcc Solid Solution Alloys, Zhenggang Wu

Doctoral Dissertations

Compared to decades-old theories of strengthening in dilute solid solutions, the mechanical behavior of concentrated solid solutions is relatively poorly understood. A special subset of these materials includes alloys in which the constituent elements are present in equal atomic proportions, including the high-entropy alloys of recent interest. A unique characteristic of equiatomic alloys is the absence of “solvent” and “solute” atoms, resulting in a breakdown of the textbook picture of dislocations moving through a solvent lattice and encountering discrete solute obstacles. To clarify the mechanical behavior of this interesting new class of materials, we investigate here a family of equiatomic …

Go to article

Influence Of Grain Size And Widmanstätten Colonies On Variability Of Tensile Properties Of Forged Ti-6al-4v, Blake T. Gaspar Jun 2014

Influence Of Grain Size And Widmanstätten Colonies On Variability Of Tensile Properties Of Forged Ti-6al-4v, Blake T. Gaspar

Master's Theses

When testing forgings for specifications, it was found that some parts did not meet the requirements for mechanical properties. This triggered an investigation into two of the parts from the lot that did not meet specification. The ultimate reason for failure was due to lower than necessary yield strength and ultimate tensile strength values, as well as unwanted variability between regions of the part. Therefore, samples of the regions were tensile tested to determine the differences that existed in yield strength, ultimate tensile strength, and elongation. After tensile testing, quantitative metallography and fractography were conducted to identify aspects of the …

Go to article

Mathematically Modeling The Mechanical Constants Of Thoracolumbar Fascia Under Compression, In Vivo, Vrajeshri Patel Jan 2014

Mathematically Modeling The Mechanical Constants Of Thoracolumbar Fascia Under Compression, In Vivo, Vrajeshri Patel

Theses

The thoracolumbar fascia (TLF) is a complex structure made of many interconnecting aponeurosis and muscle fascia. It plays a role in posture, stabilizing the lumbosacral spine, load transfer, and respiration. Its complex structure and connections have mostly been observed through cadaveric studies while its mechanical properties have been addressed in only a few studies. Recently, new advances in ultrasound imaging have made it possible to move towards measuring tissue strain. Since this is an in vivo method, mechanical data of tissues in their natural environment allows a more accurate representation of tissue strain. However, many different methods of analyzing ultrasound …

Go to article

Development Of Practical Applications For Reprap Style 3-D Printers In Engineering, Benjamin T. Wittbrodt Jan 2014

Development Of Practical Applications For Reprap Style 3-D Printers In Engineering, Benjamin T. Wittbrodt

Dissertations, Master's Theses and Master's Reports - Open

The current rise in popularity of consumer level 3-D printers introduces a need to understand the application and material property capabilities of the technology. Presented here is data demonstrating the ability for the average U.S. consumer to recuperate the cost of a 3-D printer within one year of ownership. Additionally, using a consumer level 3-D printer, multiple photovoltaic (PV) racking systems were printed and produced with much lower cost compared to commercially available aluminum racking. Additionally, mechanical testing on 3-D printed components showed a temperature dependence on both percent crystallinity and ultimate tensile strength. Conclusions are drawn using the information …

Go to article

Assembly And Mechanical Characterization Of Suspended Boron Nitride Nanotubes, Rachel Waxman Jan 2014

Assembly And Mechanical Characterization Of Suspended Boron Nitride Nanotubes, Rachel Waxman

Theses and Dissertations

This study details the dielectrophoretic assembly and mechanical characterization of boron nitride nanotubes on silicon chips with gold electrodes. The chips were fabricated from 4in round silicon wafers with a 100nm-thick low stress silicon nitride insulating layer on the top and bottom. The electrodes were patterned using photo- and electron-beam lithography and dry etching, and the wafers were cut into 4 x 6mm chips. The boron nitride nanotubes studied were obtained from NIA and were synthesized via a unique pressurized vapor/condensor method, which produced long, small-diameter BNNTs without the use of a catalyst. These nanotubes were studied due to their …

Go to article