Engineering Commons^™

Laser Doppler Velocimetry Research Of The Blowby Gas Characteristics In An Internal Combustion Engine, Mark Kevin Coffill

Masters Theses

The project was designed to measure a reciprocating engine fluid flow (blowby gases past the piston rings) using a laser doppler velocimeter (LDV). Blowby gases were obtained by introducing compressed air into an engine cylinder (piston held at TDC) to simulate engine combustion pressures. Beginning the proposed research included starting an LDV/reciprocating engine laboratory at Western Michigan University and determining the limits of the measurement devices (LDV system in particular).

The limitations which were found in the LDV system only allowed for limited results of in cylinder optical measurements. The results obtained were for cylinder pressures below 0.6 kPa gauge …

An Integrated Simulation Model Development Environment For Slam Ii Using Object-Oriented Paradigm, Rizvan Erol

Masters Theses

An integrated simulation model development environment was implemented to assist the modeler by automating certain activities of simulation modeling. The system included interactive model definition, experimental design, automatic simulation program generation in SLAM II. Object-oriented paradigm at software development stage was extensively used to conceptualize the structure, and rules of the SLAM II language in order to generate efficient, and modular program code. The present system targeted modeling of various probabilistic inventory control system problems. The remarkable advantages of the system were rapid model development time, and achieving reliable program code without requiring any knowledge in SLAM II. Object-oriented programming …

A Study Of The Effects Of Polyacrylates On Water Retention And Binder Migration Tendencies Of Coatings, Wichan Charoenkitsupat

Masters Theses

Five commercial polyacrylate samples were used to study their effects on viscosity, water holding, and binder migration under non-pressure conditions. The polyacrylates used were different in acid level, degree of crosslinking, and type of polymer (copolymer and terpolymer). A series of coatings was prepared using a number two clay and three styrene-butadiene latexes of similar particle size and T⋁g but different degrees of carboxylation, then the polyacrylates were added at several levels. The coatings were evaluated for rheological properties, water loss rate and binder migration. The results show that with increasing amounts of polyacrylates, the viscosity increased and the water …

A Computer Simulation Of The Rotary Vacuum Filter Brown Stock Washing System Using Distribution Sampling, Edison G. Yiu

Masters Theses

A probabilistic model was utilized to simulate the brown stock washing system's error due to process variability and measurement noise. Mass balances of the washing system were performed using distribution sampling. This model relies on a nonlinear relationship between displacement and dilution, which permitted the generation of displacement ratio based upon wash liquor ratio. Experimental trials were performed on a pilotscale rotary vacuum single-stage washer. Nonlinear first-order relationship appears to characterize a pilotscale washer adequately. Differences were observed between the means and standard deviations of the measured results compared to the simulation output. Future work is needed to identify the …

A Study Of The Effects Of Pigment Size And Shape On Binder Migration, Hee Jong Yang

Masters Theses

The effects of pigment size and shape on coating structure and binder migration has been investigated. Clays and ground calcium carbonates of different particle size distributions were used in coatings with 15 pph SB latex.

Coatings were applied to Mylar and a special Tyvek using a wire wound rod. The coatings were dried slowly under ambient conditions, and using hot air immediately or after having been allowed to reach immobilization through penetration into the Tyvek. The dried coatings were evaluated for water holding, relative pore size and migration using the UV technique to measure the increase in SB latex at …

Prediction Of Paper Color: A Process Simulation Approach, Mayank Chaturvedi

Masters Theses

A simulation model was developed for a dye mixing process and for the prediction of the optical properties of the paper. The model was integrated with the MAPPS (Modular Analysis of Pulp and Paper Systems) simulation software package. The model was validated using dyed handsheets made in a laboratory and dyed paper made on a pilot papermachine. Validation comprised of prediction of the optical properties of the handsheets and the machine-made paper which contained various combinations of three non-fluorescent dyes. Sheet reflectances were predicted at 20 nanometer intervals for discrete light wavelength range of 400 to 700 nanometers and verified …

A Study Of The Effect Of Water-Soluble Polymers On Water Holding And Binder Migration Tendencies Of Coatings, Joginder S. Malik

Masters Theses

Water-soluble polymers are being used in the paper coating industry for a variety of purposes including the development of water holding, viscosity control, structure and binder migration control. This study was designed to evaluate the degree that selected types of water-soluble polymers (carboxymethylcellulose, hydroxyethylcellulose, sodium alginate, polyvinyl alcohol and a polyacrylate) influence these properties. The methodology comprised of recently developed techniques in which water holding, immobilization solids and binder migration could all be measured for similar coatings applied on a paper-like porous substrate. The results illustrated that watersoluble polymers affect both the water-loss rate and binder migration, but reduce the …

On Planar Routing Of Multi-Terminal Nets In Vlsi Physical Design, Jahangir A. Hashmi

Masters Theses

In this thesis, we study two problems related to the physical design of VLSI circuits. One problem is related to the VLSI global routing and the other is related to the detailed routing in a bounded region.

We consider the routing of multiple multi-terminal nets on a single layer. We suggest a new approach for this problem. Our approach is based on simultaneously finding a forest of k non-intersecting spanning trees. We present an O(n^3) algorithm for finding two spanning trees corresponding to two nets on a single layer.

We also study the problem of finding a minimum Steiner tree …

The Indentation Of Foam Pattern Surfaces By Coordinate Measuring Machine Probes, Sanjay Nenawati

Masters Theses

When coordinate measuring machines are used to measure the complex shapes of foam patterns, the spherical probe tips indent into the soft surface of the pattern. Such indentation represents a measurement error since the indicated dimension will not be the same as the actual dimension. To determine the magnitude of error, the depth of probe tip indentation into PMMA and EPS foam surface (i.e., elastic indentation) was measured as a function of time, applied load, and foam density. The residual indentation after the removal of the load (i.e., plastic indentation) was also studied.

The depth of elastic indentation increased with …

Computational Simulation Of Flow Through Elbows In The Approach Piping Systems To A Headbox, Kasinathan Ramanathan

Masters Theses

The successful operation of the wet end in a paper machine is highly dependent on the approach piping system. Sheet basis weight stability and ease of making wet end adjustments are greatly impaired by improperly designed approach piping systems. Most problems in headbox approach piping occur when the flow splits, combines, and passes through elbows.

Elbows create cross flows, flow separation, and eddies, and play an important role in the uniform and stable delivery of the pulp into the headbox. The effect due to an elbow lasts for a considerable distance downstream of the elbow and is severe when two …

Optimization Of Sodium Carbonate-Sodium Hydroxide Pulping Of Wheat Straw For Corrugating Medium Production, Irmak Yayin

Masters Theses

This study's primary objective was to present sodium carbonate pulping as an alternative to soda or lime pulping of wheat straw for corrugating medium production. If sodium carbonate pulping is comparable with soda pulping in terms of strength properties, it could be the preference of choice because the recovery of sodium carbonate is simpler requiring less capital investment. The two strength properties that were optimized with respect to total chemical charge, cooking time, and sodium hydroxide fraction in the cooking liquor were Concora crush resistance and STFI compressive strength. These are the two most important strength properties for the end …

Using Computerized Cinematography To Develop A Predictive Model Relating Muscle Stress And Wrist Movement, Joseph M. Kaczmar

Honors Theses

Workers in many jobs are required to perform the same tasks day after day. As a result of this repetitious work, many employees are developing what is know as Cumulative Trauma Disorders (CTD). There has been much research done on ways to prevent these disorders. Cumulative Trauma Disorders involving the wrist are of special concern. Repetitive motions and awkward positions of the wrist are a major cause of CTD's in the wrist. One such factor dealing with the posture is the angle between the hand and the forearm. In order to help limit the affects of CTD's of the wrist, …

Particle Size And Velocity Measurements In Two Phase Flows Using Laser Doppler Velocimetry, Joseph Parker

Honors Theses

Laser Doppler Velocimetry is used in fluid mechanics to measure the velocity of particles in fluid flows. A small particle exhibits motion closely corresponding to the fluid behavior because of its ability to follow high frequency flow fluctuations. Large particles do not follow the flow field precisely but represent a second phase. This project used LDV to measure the size and velocity of particles in two phase flows by computer analysis of the Doppler signal.