Engineering Commons^™

Characterization Of Two-Dimensional Oculomotor Control During Goal-Directed Eye Movements In Humans, Vincent Dang

Master's Theses (2009 -)

Oculomotor control is a subset of sensorimotor control that allows humans to make extremely accurate eye movements for ADL. Impairments to oculomotor control can increase the impact of sensorimotor control deficits, especially in neurodegenerative diseases such as MS. Here, a two-dimensional computational control system of saccades and smooth-pursuit eye movements was compiled from literature to systematically characterize oculomotor control in eight visually-healthy humans as a precursor to studying the relationship between oculomotor and sensorimotor control in patient populations. Subjects visually tracked a single dot on a 41 x 30.5 cm monitor in a dark room while eye positions were recorded …

Quantification Of Local Hemodynamic Alterations Caused By Virtual Implantation Of Three Commercially-Available Stents For The Treatment Of Aortic Coarctation, Sung Kwon

Master's Theses (2009 -)

Patients with coarctation of the aorta (CoA) are prone to morbidity including atherosclerotic plaque that has been shown to correlate with altered wall shear stress (WSS) in the descending thoracic aorta (dAo). We created the first patient-specific computational fluid dynamics (CFD) model of a CoA patient treated by Palmaz stenting, and compared resulting WSS distributions to those from virtual implantation of the NumedCP and GenesisXD stents also commonly used for CoA. CFD models were created from magnetic resonance, fluoroscopy and blood pressure (BP) data. Simulations incorporated vessel deformation, downstream vascular resistance and compliance to match measured data and generate blood …

Numerical Simulation Model On Irreversibility Of Shock-Wave Process, Longhao Huang

Master's Theses (2009 -)

The objective of this research is to develop a better understanding of the irreversibilities associated with the shock compaction of matter, especially as a result of impact. Due to complex shock processes, experimentation alone cannot fix the material state, since properties such as internal energy, entropy as well as the shock process are not measurable. Thus, in addition to experimentation, analytical and numerical methods are also used to completely characterize the shock process, although they are restricted by underlying constitutive assumptions. Instead of using artificial irreversibility, such as artificial viscosity to simplify and stabilize the numeric shock model, this work …

Automation Of Energy Demand Forecasting, Sanzad Siddique

Master's Theses (2009 -)

Automation of energy demand forecasting saves time and effort by searching automatically for an appropriate model in a candidate model space without manual intervention. This thesis introduces a search-based approach that improves the performance of the model searching process for econometrics models. Further improvements in the accuracy of the energy demand forecasting are achieved by integrating nonlinear transformations within the models. This thesis introduces machine learning techniques that are capable of modeling such nonlinearity. Algorithms for learning domain knowledge from time series data using the machine learning methods are also presented. The novel search based approach and the machine learning …

Anaerobic Co-Digestion Planning And Research For Green Bay, Wi, Jonathan Kusowski

Master's Theses (2009 -)

The aspiration to find an alternative sustainable fuel source is an ever growing concern. Anaerobic digestion might hold the answer to finding an alternative sustainable energy source. Anaerobic digestion does not only provide a renewable resource in the form of biogas, but also stabilizes wastes, preventing large amounts from being landfilled or incinerated. Anaerobic digestion of municipal wastewater sludges can often be improved by the addition of high strength industrial wastes, in a process called co-digestion. High strength industrial wastes provide an additional carbon source for the microbes to utilize and convert into usable biogas. Co-digestion also offers the opportunity …

Developing Mhealth Solutions For Natural Family Planning, Md Miftah Uddin

Master's Theses (2009 -)

Natural Family Planning (NFP) is a method to help couples determine the fertile and infertile times of a woman’s menstrual cycle with natural indicators of fertility. NFP methods have advantages over other methods of family planning. Proper use of NFP methods also ensures high effectiveness (close to 98%) in helping couples avoid pregnancy. However, very few physicians prescribe NFP to their patients due to lack of credibility to the fertility methods and lack of access to NFP knowledge. The Marquette University College of Nursing Institute for Natural Family Planning has been researching for many years to increase knowledge and efficiency …

Admittance Selection For Force Guided Assembly With Optimal Motion, Fernando Rodriguez Anton

Master's Theses (2009 -)

t

Current robots lack the precise relative positioning necessary to complete automatic assembly tasks. Several solutions have been proposed. Some approaches use complex vision and force sensing systems to generate corrective motion if misalignment is present in the assembly task. Other solutions rely on generating elastic behavior, known as compliance, between the end eector and the held movable part. This compliant mechanism helps guide the movable part of the assembly into its proper position. The project focuses on designing a process by which passive compliant systems can achieve successful assembly for a range of misalignment and generate error-reducing motion that …

Ion Exchange Nutrient Recovery From Municipal Wastewater, Allen Williams

Master's Theses (2009 -)

Nitrogen and phosphorus discharge is regulated due to eutrophication. Typically ammonium-nitrogen is removed through nitrification which requires energy and phosphorus (P) is removed by metal salt addition to precipitate P. A more sustainable approach may be to implement nutrient recovery to form fertilizers. Most nitrogen fertilizer is formed through the energy intensive Haber-Bosch process. Phosphate rock, a limited resource, is mined for P fertilizer. Discharge regulations and the fertilizer production costs provide an economic driver for recovery. The current project used anionic and cationic ion exchange (IX) to concentrate the nutrients with recovery by struvite precipitation. Previous work lacks direct …

Characterization Of Stator Winding Short-Circuit Faults In Interior Permanent-Magnet Motor-Drive Systems, Andrew Strandt

Master's Theses (2009 -)

This thesis contains a comprehensive analysis of experimental data collected from a case-study interior permanent-magnet electric machine experiencing winding short-circuit faults of varying severity. The experimental data collected from the faulted machine is from both motoring operation energized by a PWM sensorless ac drive as well as generating operation driven by the test bed dynamometer with a resistive winding load. For both modes of operation a complete set of three-phase voltage and current signals was recorded and analyzed. The three fault diagnosis techniques applied and compared regarding their ability to diagnose and prognosticate a winding fault in an interior permanent-magnet …

Applying An Improved Mrps-Gmm Method To Detect Temporal Patterns In Dynamic Data System, Shaobo Wang

Master's Theses (2009 -)

The purpose of this thesis is to introduce an improved approach for the temporal pattern detection, which is based on the Multivariate Reconstructed Phase Space (MRPS) and the Gaussian Mixture Model (GMM), to overcome the disadvantage caused by the diversity of shapes among different temporal patterns in multiple nonlinear time series. Moreover, this thesis presents an applicable software program developed with MATLAB for users to utilize this approach. A major study involving dynamic data systems is to understand the correspondence between events of interest and predictive temporal patterns in the output observations, which can be used to develop a mechanism …

Effects Of Bit Type On Maximum Torque And Axial Force Using Manual Screwdrivers, Mark Hickok

Master's Theses (2009 -)

The screwdriver is a tool that has been among the most widely used hand tools for decades and continues to be used in the workplace to perform a variety of fastening tasks. Advancements in fastener technology have been complemented by the development of new types of screwdriver bits. While designs may vary, so do the force application requirements placed on the tool user. The primary objective of this experiment is to analyze the relationship between user torque and screwdriver bit design. A further objective is to utilize the results to develop an effort metric by which bits of different designs …

An Investigation Of Phase-Change Effects During Rapid Compression Machine Experiments, Colin Banyon

Master's Theses (2009 -)

Rapid compression machines (RCMs) are well characterized laboratory scale devices capable of achieving internal combustion (IC) engine relevant thermodynamic environments. These machines are often used to collect ignition delay times as targets for gas-phase chemical kinetic fuel autoigntion models. Modern RCMs utilize creviced piston(s) to improve charge homogeneity and allow for an adequate validation of detailed chemistry mechanisms against experiments using computationally efficient, homogeneous reactor models (HRMs). Conventionally, experiments are preformed by introducing a premixed gas of fuel + oxidizer + diluent into the machine, which is compressed volumetrically via a piston. Experiments investigating low-vapor pressure fuels (e.g. diesels, biodiesels, …

Comparison Of Three Space Vector Pwm Methods For A Three-Level Inverter With A Permanent Magnet Machine Load, Alia Rebecca Strandt

Master's Theses (2009 -)

Much work exists on multilevel space vector pulse width modulation (PWM) to drive induction machines, in which the rotor currents are induced by stator rotating field effects. However, there are few investigations that analyze these modulation methods applied to permanent magnet (PM) and wound-field synchronous machines, in which the rotor induces a back emf in the stator. In this thesis, three different three-level space vector PWM switching sequences are applied to a three-level neutral-point-clamped (NP) inverter driving an internal permanent magnet (IPM) machine load. The inherent qualities of each of the switching sequences when under the influence of a forcing …

Supraspinal Control Of Unilateral Locomotor Performance: An Fmri Study Using A Custom Pedaling Device, Brett Arand

Master's Theses (2009 -)

This study aimed to develop a novel unilateral pedaling device, validate its function, and use it in an fMRI study of bilateral vs. unilateral locomotor control. The new device is MRI compatible and allows for conventional coupled bilateral pedaling, along with decoupled unilateral pedaling. It was designed with an assistance mechanism to simulate the presence of the non-contributing leg while pedaling unilaterally. During coupled bilateral pedaling, the two legs work in unison: while one leg is extending in the downstroke, it provides support to lift the other leg back up as it is flexing in the upstroke. The device uses …

Simulation Of Power Control Of A Wind Turbine Permanent Magnet Synchronous Generator System, Nantao Huang

Master's Theses (2009 -)

This thesis presents a control system for a 2MW direct-drive permanent magnet synchronous generator wind turbine system with the objectives to capture the optimal power from the wind and ensure a maximum efficiency for this system. Moreover, in order to eliminate the electrical speed sensor mounted on the rotor shaft of the PMSG to reduce the system hardware complexity and improve the reliability of the system, a sliding mode observer based PM rotor position and speed sensorless control algorithm is presented here.

The mathematical models for the wind turbine and the permanent magnet synchronous machine are first given in this …

Miniature, High Efficiency Transducers For Use In Ultrasonic Flow Meters, Meghna Saikia

Master's Theses (2009 -)

This thesis is concerned with the development of a new type of miniature, high efficiency transducer for use in ultrasonic flow meters. The proposed transducer consists of a thin plate of a suitable piezoelectric material on which an inter-digital transducer is fabricated for the generation and detection of plate acoustic waves. When immersed in a fluid medium, this device can convert energy from plate acoustic waves (PAWs) into bulk acoustic waves (BAWs) and vice versa. It is shown that this mode coupling principle can be used to realize efficient transducers for use in ultrasonic flow meters. This transducer can be …

Flame Temperature Imaging Of A Low Nox Burner Via Laser Rayleigh Scattering, Nicholas A. Smith

Master's Theses (2009 -)

Federal and global legislation are requiring increasingly stringent emission regulation on household appliances and in particular water heater burners. Emissions like NOx (NO and NO2) are a growing concern due to their adverse health effects and contribution to tropospheric ozone, acid rain, and smog formation. As NOx is more closely controlled, appliance manufacturers are developing low emission burners for use in water heaters.

Flame temperature is strongly correlated to NOx production. Hence, characterizing flame temperatures in new burners is a key part of improving upon burners used today and the development of future burners. Temperature measurements applied to a new, …

Dynamic Modeling Of A Belt Driven Electromechanical Xy Plotter Cutter, Joseph V. Prisco

Master's Theses (2009 -)

Current industrial XY plotter cutters that use a belt driven gantry for the X motion and media feed for the Y motion sometimes have performance issues in cutting out high quality shapes. Mathematical models for these plotter cutters are not publicly available and thus the parameters critical to cut quality are not well understood. This thesis develops a dynamic, electromechanical model for the gantry arm and media feed using first principles and a non-linear friction model. These models are independently simulated and experimentally verified. In order to verify the effectiveness of the individual models, they are combined with a control …

Chemically Sensitive Polymer Coatings For Sh-Surface Acoustic Wave Sensors For The Detection Of Benzene In Water, Robert Lenisa

Master's Theses (2009 -)

Polymer-coated shear horizontal surface acoustic wave (SH-SAW) sensors are investigated for the detection of benzene in aqueous samples. The SH-SAW sensors using three-layer geometry have a single polymer sensing layer which absorbs the analyte and interacts with the surface wave. Several polymers are identified as potential improvements over current sensing films based on glass transition temperature and Hildebrand solubility parameter. The polymers investigated in this work include poly (methyl acrylate) (PMA), poly (butyl acrylate) (PBA), poly (ethylene co-vinyl acetate) (PEVA), bisphenol-A poly (dimethylsiloxane) (BPA PDMS), and bisphenol-A poly (hexamethyltrisiloxane) (BPA HMTS).

The polymers are spin coated on a lithium tantalate …

An Fmri Study On Supra-Spinal Contributions To Upper And Lower Limb Motor Control, Shancheng Bao

Master's Theses (2009 -)

The differences in the neural mechanisms contributing to upper and lower extremity movement have not been fully elucidated, and this might be a factor that leads to the ineffectiveness of rehabilitation techniques for most stroke survivors. It is unclear whether therapies designed for upper extremities should also be used for the lower extremities, and vice versa. In this study, fMRI was used to examine the supraspinal control of UE and LE movement in both neurologically intact individuals and people with post-stroke hemiparesis. We compared the location, volume, and intensity of brain activity associated with upper and lower extremity pedaling and …

A Multi-Scale Approach To A Greater Understanding Of The Behavior Of Heterogeneous Materials Under Dynamic Loading, Andrew J. Van Vooren

Master's Theses (2009 -)

The penetration of granular materials is of interest to a variety of different fields, and is an active area of research. The objective of this project is to gain understanding of the dynamics of a projectile penetrating into a granular material. To do this, experiments were run and a numerical model was created.

A dart gun was used to accelerate an aluminum dart to velocities around 100 m/s, which then impacted a target tank filled with Ottawa sand. The dart flew along a view window, which allowed for a recording of the penetration event using a high speed camera. Pressure …

The Effects Of Separating Visual And Motor Workspaces On The Generalization Of Visuomotor Adaptation Across Movement Conditions, Yuming Lei

Master's Theses (2009 -)

Separating visual and proprioceptive information in terms of workspace locations during reaching movement has been shown to disturb transfer of visuomotor adaptation across the arms. Here, we investigated whether separating visual and motor workspaces would also disturb generalization of visuomotor adaptation across movement conditions within the same arm. In our behavioral study, subjects were divided into four experimental groups (plus three control groups). The first two groups adapted to a visual rotation under a "dissociation" condition in which the targets for reaching movement were presented in midline while their arm performed reaching movement laterally. Following that, they were tested in …

Investigating The Possible Sources Of Error Using The Method Of Moments To Solve A Dielectric Scattering Problem, Phillip D. Bishop

Master's Theses (2009 -)

In an electromagnetic scattering problem, an incoming electromagnetic wave interacts with an object. The object is typically located in some medium, such as free space. When this electromagnetic wave becomes incident upon the object, the wave scatters. The goal of this work is to analyze the scattered fields for three different incoming wave types: a plane wave, a monopole line source, and a multipole line source. Each source is incident on an infinitely long circular cylinder of lossless dielectric material. Each source has a unique scattering characteristic.

The volume equivalence principle is used to replace the object geometry with mathematically …