Engineering Commons^™

Computationally Modeling The Human-Structure Interaction Response Of An Occupied Cantilevered Structure, Brennan Smith

Honors Theses

There is a limited understanding of the impact that passive human occupants have on a dynamic structural system, referred to as Human-Structure Interaction (HSI). Cantilevers are naturally prone to excessive vibrations due to their long unsupported spans, and cantilevered structures such as those commonly found in the seating area of a stadium facility or concert hall are designed to support a high density of occupancy.

This study determined that HSI in cantilevered structures can be modeled using a simple two-degree-of-freedom system. The results of the model were validated by data that was collected on a small-scale laboratory structure intentionally designed …

Evaluation Of The Geotechnical And Foundation Components On Jud Site, Mirabel W. Nkanor

Honors Theses

This thesis is part of the senior design final project of the Civil Engineering Department at the University of Mississippi. Geotechnical and foundation analyses were done on a proposed construction project for a multi-family home in Orlando, Florida. This evaluation done in this thesis follows the pre-existing geotechnical report on the side, USDA soil reports, ASCE Code 32-01 (Design of Foundations), and ASCE-7 Section 12.31.1 (Foundations and Superstructure-to-Foundation Connections).

A structural system was selected from the proposed location, on the corner of South Conway and Judge Road, and an evaluation of the Bearing Load capacity was completed to determine the …

An Investigation Into Aluminum’S Torsional Behavior Of Circular, Rectangular, And Square Cross-Sections, Marly Mcclintock

Honors Theses

The Specifications for Aluminum Structures (2020) provides the standards that structural engineers follow for aluminum design. Included in these specifications are limit state equations that use strength properties to calculate a member’s initial yield, full yield, and rupture values. One limit state that the standards currently neglect is the torsional failure of solid bars. Torsion is the act of rotation caused by a twisting force, otherwise known as torque. Future installments of the specifications hope to include torsional yielding and rupture equations, so this study investigates the validity of these proposed equations.

Two different aluminum alloys were investigated for this …

Design Of Load Bearing Wall For Low Rise Building With Partially Grouted Reinforced Masonry, Anil Bhatt

Honors Theses

The seismic and wind load acting on the 2-storeyed building of dimension 120 ft x 98 ft located in Oxford, MS, were calculated and the seismic load was considered for the design of the 120 ft long and 24 ft high load-bearing wall because it being critical. The maximum loading was computed using different load combinations. The masonry behavior and masonry specifications were considered to select the masonry unit, grout, and mortar for the load-bearing wall. The seismic design requirement for the shear and slender wall was fulfilled for the special reinforced masonry wall. The in-plane and out-of-plane loading scenarios …

Evaluating The Effects Of Seismic Loading On Concrete Reinforced Versus Precast Concrete Slab Floor Systems, Mahima Maharjan

Honors Theses

This thesis is part of the senior design capstone project of Ole Miss Department of Civil Engineering. The seismic loadings for the commercial buildings project located in Oxford, Mississippi are evaluated to fulfill the honor thesis requirement. This thesis follows the codes from American Concrete Institute (ACI), International Building Code (IBC), and ASCE-7/SEI (Minimum Design Loads and Associated Criteria for Buildings and Other Structures/Structural Engineering Institute) to design the gravitational loadings and seismic loadings.

Furthermore, a reinforced concrete slab flooring system is replaced with a precast slab flooring system to analyze the most seismic performance effective floor system for the …

Impacts Of Using Tubular Sections In Open Web Steel Joists, Hollis (Cas) L. Caswell V

Honors Theses

Open web steel joists are lightweight structural trusses used in place of I-beams to support long-span floors and roofs of open space buildings. Their slender geometry makes them highly efficient in resisting flexure, but susceptible to out-of-plane buckling in a failure mode known as lateral-torsional buckling. This failure can be avoided by running lateral bracing between joists called bridging or potentially by using tubular sections to build up the joists rather than angle sections.

It is possible that a joist design using tubular cross-sections could require less bridging and prevent the need to use erection bridging for initial joist construction. …

Housing Prefabrication And Resource Optimization, Megan Scherpereel

Honors Theses

Enclosure during construction is often time-consuming, expensive, and at the mercy of the weather. By introducing methods for manufacturing prefabricated enclosure components such as wall panels and roof sections, the impact of the three major variables is reduced. Designs for trusses, roof sections, wall sections, and foundations were developed and selected using civil engineering principles; and manufacturing and logistical processes were optimized using engineering and project management skill sets. These multi-disciplinary efforts were combined to create an accessible and versatile set of designs and instructions that can improve the effectiveness of both a skilled and non-skilled volunteer workforce. By creating …

Structural Health Monitoring Of Composite Parts: A Review, Jacob Pessin

Honors Theses

Structural health monitoring has the potential to allow composite structures to be more reliable and safer, then by using more traditional damage assessment techniques. Structural health monitoring (SHM) utilizes individual sensor units that are placed throughout the load bearing sections of a structure and gather data that is used for stress analysis and damage detection. Statistical time based algorithms are used to analyze collected data and determine both damage size and probable location from within the structure. While traditional calculations and life span analysis can be done for structures made of isotropic materials such as steel or other metals, composites …

Total Bridge Replacement Of M-13 Over Cheboyganing Creek, Daniel Burns

Honors Theses

The Michigan Department of Transportation sought a proposal consisting of design and construction engineering services for the total bridge replacement of M-13 over Cheboyganing Creek. The M-13 Bridge Project is located on M-13 over Cheboyganing Creek on the Saginaw River in Portsmouth Township, Bay County, Michigan.

Several components of the existing bridge have been rated in poor or serious condition on the National Bridge Inventory rating scale. A total bridge replacement is required and aligns with MDOT strategies to address critical infrastructure needs in the state as well as the Bay Region's five-year plan for managing bridge and culvert infrastructure. …