Engineering Commons^™

Hydrologic Characterization Of A Rain Garden Mitigating Stormwater Runoff From A Commercial Area, John T. Mcmaine

Theses and Dissertations--Biosystems and Agricultural Engineering

Impervious surfaces such as roads, sidewalks, and roofs increase the volume of runoff generated in a watershed. Traditional stormwater management techniques emphasize conveyance of runoff away from impervious surfaces in order to reduce flooding. Rain gardens are becoming popular as a different means to manage stormwater in such a way that runoff is captured and infiltrated onsite rather than conveyed offsite. A stormwater management system consisting of a rainwater harvest system, rain garden, and infiltration chamber was built at the Coca-Cola Refreshments USA, Inc. distribution center in Lexington, Kentucky during the fall of 2011. Precipitation, inflow, and water level were …

Moisture And Unit Weight Readings From A Complex Impedance Measuring Instrument, Kirk Andrew Jenkins

Theses and Dissertations--Civil Engineering

Complex Impedance Measuring Instruments (CIMI’s) are non-nuclear devices that calculate the dry unit weight and moisture content of soil by means of electromagnetic wave propagation theory. Unlike nuclear based test devices, these devices do not require certification or elaborate maintenance to own and operate. CIMI operation requires a soil specific calibration process where soil moisture and unit weight are correlated to electrical parameters. A new, smaller acrylic mold was developed as an alternative calibration tool to the manufacturer’s recommended mold. Calibrated soil models were generated using manufacturer recommended procedures as well as new procedures involving an acrylic mold. Models were …

Development Of A Design Based Intersection Safety Performance Evaluation Tool, Adam J. Kirk

Theses and Dissertations--Civil Engineering

The purpose of this research is to develop an intersection safety evaluation tool that is capable of assisting designers and planners in the assessment of alternative intersection designs. A conflict exposure model utilizing design hour volumes, intersection configuration and traffic control measures is proposed to achieve this goal. This approach makes use of data typically available for preliminary intersection design. The research goes beyond existing safety performance models which only examine non-directional average daily traffic (ADT) or practices which only account for the geometric and lane configuration of an intersection, such as conflict point analysis.

Conflict prediction models are developed …

Biological Control Of Manganese In Water Supplies In The Presence Of Humic Acids, Michael S. Snyder

Theses and Dissertations--Civil Engineering

The main objective of this study was to improve our understanding of biological filtration (biofilm type) treatment for manganese (Mn) removal in drinking water. Biological filtration treatment involves biofilms of Mn(II)-oxidizing microorganisms attached to solid filter material that remove and immobilize dissolved Mn(II) in raw water by conversion to black MnO_2(s) precipitates. Mn-biological filtration is an emerging green technology that can serve as an alternative to conventional physicochemical treatments but its full potential is hindered by various factors. These include lack of understanding the: (1) optimal removal conditions for Mn, (2) mechanisms for Mn releases of the accumulated Mn …

Experimental Comparison Study Of The Response Of Polycarbonate And Laminated Glass Blast Resistant Glazing Systems To Blast Loading, Joshua Calnan

Theses and Dissertations--Mining Engineering

This thesis recounts the experimental study of the dynamic response of polycarbonate blast resistant glazing systems to explosive loading through the use of triaxial load cells, pressure sensors, and a laser displacement gauge. This instrumentation captured the response of the glazing systems to blast loading over three phases of testing. The first phase of testing characterizes the load distribution around the perimeter and the second phase examines the repeatability of the results. The final phase of testing pushes the samples to failure. The results are then compared to HazL, a commonly used blast resistant glazing system analysis software tool. The …

Camber Control In Simply Supported Prestressed Concrete Bridge Girders, Osamah Ibrahim Mahmood

Theses and Dissertations--Civil Engineering

When designing a bridge, serviceability usually controls and is a more important factor than the ultimate capacity of the bridge or the allowable stresses. Therefore, the behavior of the bridge girder deflection and camber must be predicted as accurately as possible. Therefore, excessive camber has become one of the most common problems when constructing concrete bridges. Different methods have been developed to overcome this problem. The most common and widely used is using haunch with adjustable pedestals to overcome the excessive camber. However, this method has limitations that must be considered. Therefore, this study is evaluating the effectiveness of using …

Predicting The Dynamic Behavior Of Coal Mine Tailings Using State-Of-Practice Geotechnical Field Methods, Ali Salehian

Theses and Dissertations--Civil Engineering

This study is focused on developing a method to predict the dynamic behavior of mine tailings dams under earthquake loading. Tailings dams are a by-product of coal mining and processing activities. Mine tailings impoundments are prone to instability and failure under seismic loading as a result of the mechanical behavior of the tailings. Due to the existence of potential seismic sources in close proximity to the coal mining regions in the United States, it is necessary to assess the post-earthquake stability of these tailings dams.

To develop the aforementioned methodology, 34 cyclic triaxial tests along with vane shear tests were …

Applying Cognitive Principles To The Delivery Of Engineering Information By Different Mediums, Gabriel B. Dadi

Theses and Dissertations--Civil Engineering

Construction project performance and worker productivity are often tied to the availability and effective presentation of information, tools, materials, and equipment. While advancements in technology have improved much of the processes on a construction project, the medium of information dissemination at the construction work face has consistently relied on the use of two dimensional drawings and specifications.

Industry initiatives are driving increased collaboration through three dimensional BIM (Building Information Modeling) models. However, the added dimension partially loses its effect when presented on a two dimensional computer monitor. Other computer forms of presentation intended for mobility (PDAs, laptops, and tablets) can …

Water Quality Sensor Placement Guidance For Small Water Distribution Systems, Stacey L. Schal

Theses and Dissertations--Civil Engineering

Water distribution systems are vulnerable to intentional, along with accidental, contamination of the water supply. Contamination warning systems (CWS) are strategies to lessen the effects of contamination by delivering early indication of an event. Online quality monitoring, a network of sensors that can assess water quality and alert an operator of contamination, is a critical component of CWS, but utilities are faced with the decision of what locations are optimal for deployment of sensors. A sensor placement algorithm was developed and implemented in a commercial network distribution model (i.e. KYPIPE) to aid small utilities in sensor placement. The developed sensor …

Development Of A Constitutive Model Of Compacted Shales And Determination Of The Effect Of Weathering On Its Parameters, Isabel Cristina Gomez-Gutierrez

Theses and Dissertations--Civil Engineering

Compacted shales cause problems because they tend to degrade with time due to weathering. Degradation results in the shale deteriorating from a hard rock-like material to a soft fine-grained soil mass with lower shear strength and high deformability. Consequently, common problems that occur in embankments constructed with compacted shales include settlement and instabilities. Therefore, accelerating weathering prior to compaction by wetting and breaking down the shales before placement can reduce the deterioration during the service life of the construction. Extensive laboratory testing was performed in order to characterize the mechanical behavior of compacted shales.

Critical State theory is a clever …

Pressure Measurement At The Ballast-Tie Interface Of Railroad Track Using Matrix Based Tactile Surface Sensors, Michael T. Mchenry

Theses and Dissertations--Civil Engineering

The pressure distribution at the ballast-tie interface of railroad track plays a key role in overall track support. Failure of the ballast or tie can result from excessive loads that were not designed for, requiring increased maintenance and reducing railroad operating efficiency. Understanding the forces acting on the ballast and tie are required to design higher performance and longer lasting track. To further this understanding, the use of Matrix Based Tactile Surface Sensors (MBTSS) is employed to measure the actual pressure distribution at the ballast-tie interface, characterized by individual ballast particle contact points and non-uniform pressures. The research explores this …

Investigation Of Usage Of Velocity And Pressure Data Within A Water Distribution Lab Model For Calibrating Hydraulic Models, Robert Craig Ashby

Theses and Dissertations--Civil Engineering

Water distribution modeling for hydraulics and water quality is an important tool for managing system performance of water utilities. An important component of a water distribution model is the calibration of a network model with field data in the real world system. The calibration effort requires a protocol or selection criteria for the location of field measurements that best support the calibration effort. A water distribution model was constructed at the University of Kentucky hydraulics lab for the purpose of investigating the performance of water distribution models. The lab model contains numerous hydraulic (pressure, flows) and water quality (concentrations) sensors …

Unsaturated Soil Parameters From Field Stiffness Measurements, Jason M. Curd

Theses and Dissertations--Civil Engineering

The behavior of unsaturated soils depends heavily on material properties and soil conditions. In Geotechnical Engineering, compacted soils are frequently used as fill material, and quality control is vital to the construction process. There are few methods available to estimate the parameters associated with unsaturated soils based on field measurements, and a relationship between these factors could reduce testing time and lower construction costs. Undrained triaxial tests were performed on four clays representing a range of material properties in an effort to reach the maximum dry density, which provides the highest bearing capacity. Each clay was compacted at optimum moisture …

Two-Dimensional Hydrodynamic Modeling Of Two-Phase Flow For Understanding Geyser Phenomena In Urban Stormwater System, Zhiyu S. Shao

Theses and Dissertations--Civil Engineering

During intense rain events a stormwater system can fill rapidly and undergo a transition from open channel flow to pressurized flow. This transition can create large discrete pockets of trapped air in the system. These pockets are pressurized in the horizontal reaches of the system and then are released through vertical vents. In extreme cases, the transition and release of air pockets can create a geyser feature.

The current models are inadequate for simulating mixed flows with complicated air-water interactions, such as geysers. Additionally, the simulation of air escaping in the vertical dropshaft is greatly simplified, or completely ignored, in …

Kentrack 4.0: A Railway Trackbed Structural Design Program, Shushu Liu

Theses and Dissertations--Civil Engineering

The KENTRACK program is a finite element based railway trackbed structural design program that can be utilized to analyze trackbeds having various combinations of all-granular and asphalt-bound layered support. It is applicable for calculating compressive stresses at the top of subgrade, indicative of potential long-term trackbed settlement failure. Furthermore, for trackbeds containing asphalt layer, it is applicable for calculating tensile strains at the bottom of the asphalt layer, indicative of potential fatigue cracking. The program was recently expanded to include both English and international units. A procedure has been incorporated to provide a path to save results in a text …

Using Gis To Delineate Headwater Stream Origins In The Appalachian Coal-Belt Region Of Kentucky, Jonathan A. Villines

Theses and Dissertations--Biosystems and Agricultural Engineering

Human activity such as surface mining can have substantial impacts on the natural environment. Performing a Cumulative Hydrologic Impact Assessment (CHIA) of such impacts on surface water systems requires knowing the location and extent of these impacted streams. The Jurisdictional Determination (JD) of a stream’s protected status under the Clean Water Act (CWA) involves locating and classifying streams according to their flow regime: ephemeral, intermittent, or perennial. Due to their often remote locations and small size, taking a field inventory of headwater streams for surface mining permit applications or permit reviews is challenging. A means of estimating headwater stream location …

Froth Flotation Performance Enhancement By Feed Cavitation And Magnetic Plastic Particle Addition, Mehmet Saracoglu

Theses and Dissertations--Mining Engineering

Froth flotation is the most commonly used process to recover and upgrade the portion of the coal preparation plant feed that has a particle size smaller than 150 microns. Problems that occur when employing froth flotation in the coal industry include i) coal surfaces that are weakly-to-moderately hydrophobic, and ii) flotation systems that are overloaded and limited by insufficient retention time.

Research was performed to evaluate techniques that could be implemented to improve flotation performance under the aforementioned scenarios. Pre-aeration of flotation feed using a cavitation system was extensively evaluated in laboratory and full-scale test programs. The benefits of adding …