Engineering Commons^™

Laboratory Evaluation Of Recycled Crushed Glass Cullet For Use As An Aggregate In Beach Nourishment And Marsh Creation Projects In Southeastern Louisiana, John C. Wildman

University of New Orleans Theses and Dissertations

To combat the rapid degradation of the Louisiana coast, the Louisiana Coastal Protection and Restoration Authority has planned strategic land building initiatives throughout the Louisiana Gulf coast, including beach nourishment and marsh creation projects. It is commonly agreed that the state lacks sufficient renewable sediment resources to maintain the planned CPRA land building program. However, Louisiana, the state that commonly ranks last in state recycling percentage, recycles an estimated 0.6% of the waste glass consumed in the state. Glass is predominantly silica sand. This thesis evaluates laboratory‑determined characteristics of recycled crushed glass cullet to assess its suitability as a renewable …

Effect Of Curing Conditions On Mechanical Properties And Durability Of Concrete, Edgar Lazaro Salas-Borrero

UNLV Theses, Dissertations, Professional Papers, and Capstones

This thesis presents the results for three different concrete mix designs with compression strengths of 4500 psi. The experiment was conducted in the Las Vegas area during the summer, from August 16th to October 12th, 2018, where temperatures and relative humidity was recorded daily, three times a day. In total, 135 concrete specimens (4” x 8”) were taken on site and were subjected to five different curing conditions.

For each concrete mix design, three concrete samples (4” x 8”) were taken and submitted for each curing condition, resulting in 45 cylinders for each concrete mix design. The same number of …

Performance-Based Economical Seismic Design Of Multistory Reinforced Concrete Frame Buildings And Reliability Assessment, Chunyu Zhang

UNLV Theses, Dissertations, Professional Papers, and Capstones

As the next generation of seismic design methodology, performance-based seismic design (PBSD) method requires a structure satisfy multiple preselected performance levels under different hazard levels. Optimal PBSD methods provide different strategies to design the numerous variables, including strength, stiffness and ductility of each structural component. The overall goal of this study is to develop a new optimal PBSD method for multi-story RC moment frames. This method is capable of overcoming the deficiencies of existing optimal PBSD methods and can be implemented by the U.S. design practice. The proposed method minimizes construction cost and takes the limit of member plastic rotation …

Surface Resistivity For Concrete Quality Assurance, Stanley Tat

UNLV Theses, Dissertations, Professional Papers, and Capstones

The goal of this study was to determine the effectiveness of SRT for concrete quality assurance and to evaluate the relationship between SRT and the three chloride ion ingress methods currently used by various State DOTs. Additionally, the influence of binder type and content, concrete age, and water-to cementitious materials ratio on the experimental results were also examined.

In this study, Type V Portland and three SCMs; namely fly ash, slag, and silica fume were used. Fine and coarse, aggregates were supplied by a local quarry. To evaluate the transport properties of the studied concretes, RMT, RCPT, and ACT were …

Calculation Of Access Charge For High Speed Rail Xpresswest Of Nevada, Sameeksha Sapkota

UNLV Theses, Dissertations, Professional Papers, and Capstones

XpressWest is a High Speed Rail (HSR) system that plans to connect Las Vegas with California at Palmdale. It will utilize the railway network of the California High Speed Rail (CAHSR) to connect Las Vegas with California destinations that include Los Angeles and San Francisco. For sharing the railway network of CAHSR, XpressWest will pay certain charge known as an access charge. The access charge is the fee paid by the train operator to the infrastructure owner for the addition of trains in a track. There are several access charge systems in the world. However, there is no study that …

An Engineered Fit-For-Purpose Polymer Nanocomposite Seal Repair Material For Wellbores, Moneeb Genedy

Civil Engineering ETDs

Seal integrity of wellbores has become of significant interest due to repeated leakage and spill incidents occurring worldwide that jeopardize both human health and the environment in addition to causing significant economic burden. This is attributed to the fact that wellbores intersecting geographical formations contain potential leakage pathways. The cement-steel and cement-rock formation interfaces are recognized as two critical leakage pathways.

A seal repair material that has good bond strength with both steel and rock formations in addition to the ability to completely fill thin microcracks is needed to restore the seal integrity of wellbores. In this research, engineered polymer …

Treated Versus Untreated Aggregate Bases For Flexible Pavements: A Nationwide Comparitive Study, Hemant Gc, Mena I. Souliman

Civil Engineering Theses

Aggregates are a major part of highway construction and its quality as well as strength affects the overall performance of the pavement structure. The base material near the construction site does not always meet the strength requirement needed for the pavement construction and the hauling of quality aggregate increases the construction costs. For better use of local available materials, stabilizing agents such as lime and asphalt cement have been utilized to increase the strength of crushed aggregate bases. Performance of pavement structures is heavily influenced by the thickness of the structure as well as material properties of each layer. The …

Improving Ductility Of Slender Reinforced Concrete Shear Walls With Frp Sheets And Splay Anchors, Luke M. Ostrom

Architectural Engineering

The Sylmar earthquake of 1971 caused significant damage to slender, non-ductile reinforced concrete (RC) shear wall buildings in California. A later survey by the Concrete Coalition in 2011, under the guidance of EERI members, indicated that there are over 3000 vulnerable concrete buildings in California [8]. This led to City of Los Angeles (LA) Ordinance 193893 enacted in 2015, which requires mandatory upgrades to these concrete buildings by 2035. Current practice to meet the requirements of this ordinance, with respect to RC wall buildings, involves adding new shear walls to the building plan or increasing the cross-sectional area of existing …

A Microscopic Simulation Laboratory For Evaluation Of Off-Street Parking Systems, Yun Yuan

Theses and Dissertations

The parking industry produces an enormous amount of data every day that, properly analyzed, will change the way the industry operates. The collected data form patterns that, in most cases, would allow parking operators and property owners to better understand how to maximize revenue and decrease operating expenses and support the decisions such as how to set specific parking policies (e.g. electrical charging only parking space) to achieve the sustainable and eco-friendly parking.

However, there lacks an intelligent tool to assess the layout design and operational performance of parking lots to reduce the externalities and increase the revenue. To address …

Evaluation And Influence Of Recycled Concrete Aggregate Base Layers On Hma Pavement Performance, Jessie Daniel Ramirez

Theses and Dissertations

This research investigated the influence of the RCA base layers on the HMA pavement performance as compared with CA base layers using laboratory tests on collected base layer materials and field tests on corresponding pavement sections. Field and laboratory testing programs were conducted to investigate RCA and CA base layer materials in which identified test sections at the selected pavement sites were subjected to testing using FWD, walking profiler, and DCP. Visual distress surveys were also conducted at the selected pavement sections. RCA and CA base layer samples were collected from these pavement sites and were subjected to a laboratory …

On The Development Of 8,000 Psi Geopolymer Mortar For Practical Use In Field Applications, Remington Gabriel Reed

Graduate Theses and Dissertations

Although there are several perceived benefits from the use of geopolymer binder as an alternative to ordinary portland cement in concrete materials, it is not widely used in field applications. Geopolymer materials have no set guidelines for mixture design and often require heat curing to facilitate strength gain. Additionally, many geopolymers are created using carefully controlled and high quality materials and activator chemicals. These factors greatly affect the practicality of the material. The goal of this research was to create a geopolymer material capable of achieving high compressive strengths at 28 days without heat curing, and using only readily available …

Developing Ultra-High Performance Concrete (Uhpc) With Locally Available Materials, Ali Alsalman

Graduate Theses and Dissertations

Ultra-High Performance Concrete (UHPC) can enhance the durability and resilience of concrete structures. The use of local materials is a fundamental step to save energy and reduce the cost of concrete. The main focus of this research was to develop a UHPC with compressive strength of 150 MPa using locally sources materials. In this study, the effect of fine materials, binder type and content, type of mixer, steel fibers and curing regimes on concrete’s compressive strength were investigated. The relationship between compressive strength and elastic modulus was also studied. This study synthesizes all relevant experimental data in the literature to …

Effect Of Continuity Plate Eccentricity On The Performance Of Welded Beam-To-Column Connections, Jason Thomas Norwood

Graduate Theses and Dissertations

Beam-to-column connections in structural steel buildings may have varying degrees of rotational restraint and varying degrees of moment transfer. In fully restrained moment connections, shear is typically transferred through the beam web, while the moment is mostly transferred through the beam flanges which create tension/compression force couples. Column sections that are incapable of resisting these flange forces are often retrofitted with continuity plates within the connection region to improve capacity. In cases of unequal beam depths on either side of the column, an eccentricity between the framed-in beam flange and continuity plate may be required; however, limited research exists to …

Utilizing The Hvsr Second Peak For Surface Wave Inversions In The Mississippi Embayment, Ashraf Kamal Himel

Graduate Theses and Dissertations

Ambient noise data from 24 sites within the Mississippi Embayment were analyzed to estimate the fundamental frequency using the horizontal to vertical spectral ratio (HVSR) method. The fundamental frequency ranged from 0.17 to 3.43 Hz for the tested sites. At seventeen of the sites, a second higher frequency HVSR peak, which ranged from 0.617 Hz to 2.154 Hz, was observed in addition to the fundamental HVSR peak. The second peak frequency in the HVSR curve has been attributed by previous researchers as either an odd harmonic of the fundamental peak or a shallow impedance contrast from the Memphis sand layer …

Development Of Anti-Icing Airfield Heated Pavement Systems Using Solar Energy, Joseph Daniels

Graduate Theses and Dissertations

This dissertation analyzes developing and assessing the viability of an anti-icing airfield heated pavement system using solar energy. This study includes two components, a field experimentation component and a numerical analysis component. Field experimentation investigates two systems: (1) an electrical heated pavement system with a photovoltaic energy system as its power source, and (2) a hydronic heated pavement system with a solar water-heating system as its heating source. The systems operate under an automated thermostat heating sequence for operation optimization and energy conservation. Study results found the solar systems capable of supplying enough energy to maintain pavement surface temperature above …

Effect Of Cement Content On Concrete Performance, Caleb Joshua Lebow

Graduate Theses and Dissertations

Of all the traditional concrete materials, portland cement has the greatest impact on mixture cost and the environment. Cement is in many ways the glue holding concrete together (Weiss, 1999), and as such, it plays a major role in fresh and hardened concrete properties. Without the proper range of cement in the mixture, low strength development or excessive shrinkage may occur leading to premature deterioration. The Arkansas Department of Transportation (ARDOT) recognizes two types of concrete for use in bridge construction, Class S and Class S(AE). This paper focuses on the findings from testing of Class S(AE) concrete, short for …

Early Life Flexural Performance And Behavior Of Reinforced Bcsa Concrete Beams, Gabriel Cook

Graduate Theses and Dissertations

Belitic calcium sulfoaluminate cement (BCSA) is a hydraulic, rapid setting alternative to ordinary portland cement (OPC) with reduced energy demands and CO2 emissions. BCSA cement has numerous current and potential applications including transportation repair and precast manufacturing. Currently, limited research exists regarding the structural performance of CSA cements, restricting its potential implementation. Thus, the purpose of this research is to provide insight into the flexural performance and behavior of reinforced BCSA concrete beams. Overall, BCSA concrete had similar cracking and loading behavior to the OPC beams, with increased moment capacity for compression controlled specimens. Furthermore, BCSA concrete showed increased tensile …

Examining The Use Of Idealized Granular Material In Validated Dem Simulations, Anjana Thoroppady Kittu

Graduate Theses and Dissertations

Discrete element method (DEM) modeling, is becoming widely used for understanding the micro-mechanical behavior of granular materials at the particle level. This dissertation presents important considerations regarding the experimental boundary conditions and idealized granular materials used in DEM validations.

A common issue in DEM validation studies for direct shear and direct simple shear is selecting top and bottom cap boundary conditions that allow for shear transmission while also being efficiently modeled in the DEM simulations. While the traditional grid boundary types used in the laboratory can be replicated in the numerical models, researchers have also used fixed-particle boundaries, sawtooth boundaries, …

Fatigue Performance And Shear Demand Distributions Of Clustered Shear Connectors In Composite Bridge Girders, Brian David Hillhouse

Graduate Theses and Dissertations

The current American Association of State Highway and Transportation Officials (AASHTO) Bridge Specifications assumes uniform shear flow demands at the steel-concrete interface of composite bridge girders. As stud pitch increases to beyond 24 in or as studs become clustered to account for pre-cast concrete decks, this assumed shear demand distribution may be unrepresentative. Understanding shear transfer and resulting demands on headed studs in composite beams are important for ensuring adequate composite design. This study investigates stud demands in composite bridge girders using large-scale fatigue testing and direct pressure measurements for stud force calculations. In this study, two large-scale composite beam …

Accumulation Of Lead By Biofilms In Drinking Water Distribution Systems, Kaleb Oren Belcher

Graduate Theses and Dissertations

Recent crises, such as the one in Flint, MI, indicate that lead exposure from drinking water is a major health concern in the United States. Over six million lead service lines are still in use in the United States, and a universal protocol to safely remove these lead service lines from drinking water distribution systems has not yet been established. This paper calls to attention the potential hazard that biofilms pose as a source of lead in distribution systems, even after the removal of lead pipes. This study used a simulated water distribution system containing a lead source pipe and …

Developing Computer Codes For Analyzing Bridge Response Due To Wim Data Truck Loading, Kenneth Patrick Pasley

Graduate Theses and Dissertations

Despite actual truck demographics evolving over the past 30 years, the Arkansas legal loads for bridge posting have not been updated. Custom computer codes were developed.to facilitate comparison between the current Arkansas legal loads for bridge posting and the actual Arkansas truck traffic to ensure that actual reactions are enveloped by the state'. The program, WIMFluence, calculates shear and moment influence lines for a bridge and the resulting shear and moment reactions based on weigh-in-motion data. With supporting scripts, the reactions due to actual Arkansas truck traffic were compared to those due to the current Arkansas legal loads for bridge …

Controlling Relative Humidity Using Glycerin, Juan Martinez

Civil Engineering Undergraduate Honors Theses

A series of tests were conducted to control relative humidity (RH) using a bubbler system that contained a series of glass jars and glass vials filled with different concentrations of glycerin. The relative humidity within the glass jars was measured. The total time interval for each laboratory test was 48 hours. During the first 24 hours a pump was used to bubble air through the glycerin solution. During the second 24 hours, the pump was turned off, and the RH within the system was monitored within the closed system. Target RH measurements from 100% to a 0% were obtained. The …

Physio-Chemical Degradation Of Concrete: A Ramification Of Coupled Freeze-Thaw And Sulfate Attack, Md Aminul Islam

Boise State University Theses and Dissertations

Concrete structures experience damage due to Sulfate Attack (SA) and Freeze-Thaw (F-T) in cold regions containing ample amount of sulfate species. The combined effect of SA and F-T is a multiscale multiphysics damaging process for cementitious materials involving complicated chemical reactions and phase transition inside concrete pores. This thesis is a compilation of two theoretical models describing the SA induced damage in an unsaturated cementitious medium and damage due to the combined effect of SA and F-T. The classical theory of phase change and a diffusion-reaction process is utilized in the development of the models. The validity of the proposed …

The Passive Effects Of Full-Gateway, In-Street Signs On Vehicular Speed, De'lon Dixon

Masters Theses

Reducing motorist’s speed when approaching crosswalks is an important goal in reducing the number of collision between motorist and pedestrian in crosswalks. The current study addresses this goal. The effect of gateway installation of in-street signs (one in-street sign installed between the two travel lanes in each direction and one on both edges of the roadway in each direction) on vehicle speed was evaluated on nine roads. The results demonstrated that the Gateway in-street sign treatment produced large speed reductions as vehicles approached the crosswalk and at the crosswalk. The average speed reduction was 3.8 mph at the crosswalk and …

Enabling Robust Distributed Real-Time Hybrid Simulation Method And Expanding Its Applications In Floating Wind Turbine Systems, Mehmet Cinar

Masters Theses

Real-time hybrid simulation (RTHS), which integrates physical experiment and numerical simulation, plays an essential role in understanding the time-dependent behavior of structures when subject to hazardous loadings. On the other hand, RTHS might not yield accurate results for complex structural systems due to experimental and computational limitations. Distributed real-time hybrid simulation (dRTHS), which takes the advantage of distributed laboratory facilities using network communications, was proposed and proven to address some limitations in RTHS. During dRTHS, Internet delay due to the network communication is added to the actuator delay in RTHS, which may cause inaccurate results or even unstable tests. To …

Evaluation Of A Centrifuge Consolidation Technique To Determine The Effects Of Temperature And Time On Kaolinite Properties, Esteban Miranda Pinzon

Civil Engineering Undergraduate Honors Theses

Abstract

The effects of time and temperature on the moisture content and unit weight profiles, as developed during a centrifuge consolidation process, were observed during the research program that is described herein. Specifically, a Beckman-Coulter Model J6-MI centrifuge with a six-place JS-4.2A swinging bucket rotor was utilized to consolidate kaolinite slurry samples. The consolidation procedure utilized specially designed slurry consolidometers, made from acrylic tubes with inside diameters of 2.63 inches (6.67 cm) and heights of 5.13 inches (13.04 cm). The tested kaolinite slurry samples were created by mixing 400 grams of dry kaolinite clay powder with 200 grams of de-aired …

Automation Of Post-Earthquake Civil Infrastructure Reconnaissance, Jack Bergquist

Architectural Engineering

Traditionally post-earthquake structural engineering reconnaissance consists of a team of experts who are deployed to the field to record and capture earthquake damage data, which is later uploaded into online repositories. Despite many advances to these data archives in recent years, the entries in online repositories often have limited metadata which make it difficult and time consuming to extract specific damage evidence that can be used for meaningful analysis. This report outlines the author’s contributions to overcoming these challenges via the development of a neural network that automatically filters and classifies post-earthquake civil infrastructure damage data after a seismic event. …

Utilizing 3d Printed Analogue Soils To Investigate Specimen Size Effects In Triaxial Testing, Claire Louise Stewart

Graduate Theses and Dissertations

Triaxial testing is one of the fundamental laboratory tests used in geotechnical engineering to determine strength parameters, such as shear strength and friction angle. Investigating the minimum representative elementary volume (REV) can verify the independence of size effects on strength parameters and ensure that the scaled laboratory tests results are consistent, repeatable, and representative of field conditions. Although, REV has been studied for many applications, there is disagreement within geotechnical engineering of a minimum particle diameter to specimen diameter to minimize the size effects related to the REV in consolidated drained (CD) triaxial tests. This research study compared the strength …

Young’S Modulus As A Measurement To Estimate Damage Related With Alkali-Silica Reaction In Concrete., Anazaria J. Ortega Gonzalez

Civil Engineering Undergraduate Honors Theses

The main purpose of this research is to compare two nondestructive methods to assess Alkali-Silica reaction (ASR) in concrete. Fifteen concrete prisms were cast using aggregates with different Alkali-Silica reactivity such as Jobe sand and Van Buren sand. The change in strain, shear wave velocity and Young’s modulus were determined according to ASTM C129 and ASTM C215, respectively. This data was collected by Dillon K Self, who determined that the shear wave velocity and strain are inversely proportional. However, when single cracking in the concrete specimen transition to map cracking, the shear wave velocity dropped significantly, whereas the strain value …

A Stormwater Management Model For California Polytechnic State University Campus, Hsuan-Wen Chu

Master's Theses

Developments that have been taking place on Cal Poly campus over the years have altered the natural hydrology of the area. Stormwater management practices could help reduce the impacts of these developments. Computer models can help to design effective and economical stormwater management solutions at a watershed scale. As such, the objective of this study was to develop a stormwater management model for Cal Poly campus. The model was developed based on the utility data obtained from the university and other watershed data available from open sources. Field surveys were conducted to address some anomalies in the utility data, and …