Engineering Commons^™

Experimental Study On The Impact Of Low Thermal Inertia Thermal Barrier Coatings On Ppci-Diffusion Gci Combustion, Kunal Vedpathak

All Theses

The application of thermal barrier coatings (TBCs) has been studied in homogenous charge compression ignition (HCCI), conventional diesel combustion (CDC), and spark ignition (SI). Gasoline compression ignition (GCI) combines the low soot and NOx emissions of HCCI with combustion controllability through fuel stratification. GCI has become an interesting prospect due to the reduction in gasoline consumption due to the electrification and hybridization of the light-duty sector. It can be used as a preferred combustion mode in heavy-duty engines to reduce emissions with minimal modifications. GCI exhibits better combustion efficiency than HCCI. Advances in material technology have combined low thermal conductivity …

Experimental Investigation Of Low Thermal Inertia Thermal Barrier Coatings For Spark Ignition Engines, John Gandolfo

All Theses

The application of thermal barrier coatings (TBCs) in spark ignition (SI) engines has historically been avoided due to the knock penalty associated with higher surface temperatures induced by the ceramic layer. However, advances in low thermal inertia coatings (i.e., temperature swing coatings) that combine low thermal conductivity with low volumetric heat capacity can prevent excessively high surface temperatures during the intake stroke and reduce or avoid knock while improving performance and efficiency. This thesis experimentally evaluates the effectiveness of these low thermal inertia coatings in a single-cylinder research engine representative of modern SI engines.

First, four pistons coated with a …

Safe Navigation Of Quadruped Robots Using Density Functions, Andrew Zheng

All Theses

Safe navigation of mission-critical systems is of utmost importance in many modern autonomous applications. Over the past decades, the approach to the problem has consisted of using probabilistic methods, such as sample-based planners, to generate feasible, safe solutions to the navigation problem. However, these methods use iterative safety checks to guarantee the safety of the system, which can become quite complex. The navigation problem can also be solved in feedback form using potential field methods. Navigation function, a class of potential field methods, is an analytical control design to give almost everywhere convergence properties, but under certain topological constraints and …

Creation And Validation Of A Novel Bayesian Calibration Method With Griddy Gibbs Sampling, Hannah Stewart

All Theses

Computer models of physical systems are widely used in lieu of, or in tandem with, experimental testing. It is critical to verify the accuracy of computer models through the process of calibration. Typical calibration methods are often computationally expensive and therefore cannot be performed in real time. This thesis presents a novel Bayesian calibration method using a Griddy Gibbs sampling algorithm to improve calibration speeds. This method was verified in two applications: a location-dependent dataset in the heat transfer analysis of an engine piston, and time-dependent tire forces in a drum test. The proposed method was directly compared to a …

Multiphysics Diesel Aftertreatment System Modeling For Reduced Emissions From Hybrid Electric Heavy-Duty Powertrains, Uday Srivastav

All Theses

Hybridization of heavy-duty on-road vehicles presents an opportunity to significantly reduce internal combustion engine emissions in real-world operation. These gains can be realized through the coordination of the electric drive, engine, and aftertreatment systems. Accurate Multiphysics models of all powertrains sub-systems are required to achieve the goal of reduced emissions. This research aims to develop a model of a highly complex diesel engine aftertreatment system. This study focuses on utilizing transient data for calibration and validation of the aftertreatment system and reducing the run time when compared to real-time experiments. The calibration focuses on two physical phenomena, thermal behavior and …

Virtual Prototyping And Validation For Autonomous Assistive Mobility, Amogh Venkataramana Reddy

All Theses

Physical disability in humans is something that no one has control over. It is catastrophic for people to experience it, and sometimes hinders them from enjoying the essence of life. Though disability is something people have no control over, they do have control on how they can go forward and make life beautiful and meaningful. Wheelchairs have helped people with disabilities in mobility, allowing them to move around with the help of others or sometimes on their own. This research will focus on development of an autonomous assistive mobility robot to help the disabled using virtual prototyping tools for development …

Life Cycle Energy Assesment Of Advanced Fiber Reinforced Composite Design And Manufacturing Methodologies, Urjit Lad

All Theses

Automotive industry at large is focused on vehicle light-weighting since a 6%-8% increase in fuel efficiency can be achieved with a 10% reduction in vehicle weight [1]. With the growing demand for cost-effective and sustainable light weighting of automobile structures, interest has increased in the application of fiber reinforced plastic (FRP) composites for use in the Body-in-White (BiW), which can account for up to 40% of the total vehicle weight. Traditional FRP composite manufacturing processes like vacuum assisted resin transfer molding, autoclave consolidation or use of automated fiber placement have been successfully used for marine and aerospace applications. However, these …