Engineering Commons^™

Numerical Analysis Of A Multi-Stage Elastohydrodynamic Seal For Aircraft Engines, Md Wasif Hasan

Electronic Theses and Dissertations

At present, both governmental and private aviation enterprises are trying to develop aircraft that are swifter, more lightweight, and more cost-effective in order to maintain competitiveness on both the domestic and global stage. Continuous innovation and sustainability efforts are necessary to achieve advancements in aviation systems, such as fans, compressors, combustors, and turbines, as well as sub-systems, like engine seals. Advanced engine seals exhibit considerable potential in enhancing the engine's pressure ratio and cycle temperatures, leading to reduced engine weight, increased thrust, and improved fuel economy. In this study, a novel multistage seal idea has been proposed for the supercritical …

Mitigation Of Aeroacoustic Noise Of A Fixed Wing Using Passive Flow Control, Cameron L. Perry

Electronic Theses and Dissertations

As the world becomes more environmentally conscious, noise pollution is of increasing concern. In this study, shallow dimples are applied to a NACA 0012 airfoil at multiple angles of attack (AoA) with the intent of reducing aeroacoustic noise emissions. Both Reynolds Averaged Navier-Stokes (RANS) and Large Eddy Simulation (LES) models are used for aerodynamic and aeroacoustic investigations, respectively, at a fixed Reynolds number of 4.8 x 10⁵. Altering the dimple depth to diameter ratio (d/D) from 2.5% to 15% is first investigated, with a d/D of 5% or lower resulting in the least aerodynamic impact. The transition from …

Computational And Experimental Investigation Of Mass Reduced Aircraft Wing Ribs, Charles R. Fricks Iii

Electronic Theses and Dissertations

This study seeks to develop and evaluate a novel design of mass reduced aircraft wing ribs through the topology optimization method. For comparison, the same examination is performed on ribs with normal internal geometry. The wing rib design is based on that of the Gulfstream G650 transonic jet. The rib was divided into three segments for analysis based around the positions of the two spars. Only the center section of the rib (that being between the forward and aft spars) is mass optimized, while the leading and trailing edges of the ribs (outside the spars) will be kept solid for …

Investigations Of A Surrogate Fuel Based On Fischer-Tropsch Gtl And Ctl In Cvcc, Idi And Di Compression Ignition Engines, Amanda C. Weaver

Electronic Theses and Dissertations

With the increase in availability, feedstocks, and properties of alternative fuels, compatibility issues emerge between current engine platforms often requiring a limit on the blend percentage of alternative fuel in conventional fuel or alteration to the engine platform. Two key metrics were identified, autoignition quality and lubrication characteristics, as vital for the proper function of a compression ignition engine, and if the blend of alternative fuels matches these two criteria for the diesel standard, then the resulting blend percentage can be considered as a viable alternative for complete replacement of conventional petroleum ULSD. Autoignition quality was matched using blends S-8, …

Computational Comparison Of Dual Bell, Expansion-Deflection, And Aerospike Nozzles, Manuel R. Abadie Ardon

Honors College Theses

In the search for a Single-Stage-to-Orbit rocket, Altitude Compensating Nozzles concepts (ACNs) have been proposed since the 1950s, but research has stalled despite the modern analysis tools available. These nozzle concepts offer optimum performance at two or more altitude settings. This research chose three of these concepts, these being the Dual Bell, Expansion-Deflection, and Aerospike, which were designed and analyzed at various pressure ratios (NPR=10,15,30,36,30,45) using Computational Fluid Dynamics (CFD) software FLUENT. Simulations generated pressure distributions along the nozzle wall, which allowed to calculate data values such as thrust coefficients. Nozzle efficiency is calculated from this data and used to …

Investigation Of The Low-Temperature Combustion Phenomena Of A Fischer-Tropsch Synthetic Aerospace Fuel In A Constant Volume Combustion Chamber For Greenhouse Gas Reduction, Lily H. Parker

Honors College Theses

Greenhouse gases (GHG) have a harmful effect on our environment as they trap heat in the atmosphere accelerating climate change. As such, the Federal Aviation Administration’s 2025 strategic plan to reduce GHG emissions from air transportation. This call to action for a more environmentally friendly option highlights the importance of synthetic fuels as they are more sustainable compared to traditional fossil fuels. An investigation was conducted into the thermal-physical properties of Synthetic Fischer-Tropsch (F-T) Sustainable Aviation Fuels (SAF) and the Low Temperature Combustion (LTC). LTC is composed of the Low Temperature Heat Release (LTHR) and Negative Temperature Coefficient (NTC) region, …

Cfd And Heat Transfer Analysis Of Rocket Cooling Techniques On An Aerospike Nozzle, Geoffrey Sullivan

Electronic Theses and Dissertations

In recent years the development of rocket engines has been mainly focused on improving the engine cycle and creating new fuels. Rocket nozzle design has not been changed since the late 1960s. Recent needs for reliable and reusable rockets, as well as advancements in additive manufacturing, have brought new interest into the aerospike nozzle concept. This nozzle is a type of altitude adjusting nozzle that is up to 90% more efficient than bell nozzles at low altitudes and spends up to 30% less fuel. Since the nozzle body is submerged in the hot exhaust gasses it is difficult to keep …

Investigations Of The Low Temperature Combustion Regions And Emissions Characteristics Of Aerospace F24 In A Constant Volume Combustion Chamber And A Common Rail Direct Injection Ci Engine, Richard C. Smith Iii

Electronic Theses and Dissertations

A study was conducted to investigate the low temperature combustion (LTC) regions of aerospace F24 and ULSD in the static setting of a CVCC and the dynamic setting of a CRDI research engine. This research is conducted to reduce in-cylinder emissions by understanding and implementing a technique to achieve an extended LTC. Emissions data for this study were collected during the operation of the CRDI research engine with a MKS 2030 FTIR and an AVL Microsoot 483. The parameters researched within the static setting of the CVCC included the determinations of the cool flames and NTC regions within the LTHR …

Comparative Analysis Of Winglet Efficiency On Supercritical Versus Traditionally Cambered Airfoils, Evan Cathers

Electronic Theses and Dissertations

This study serves to define the performance of several industry-recognized and exploratory wing tip devices on aircraft wings utilizing contemporary supercritical airfoil geometry. For comparison, the same examination is performed on a wing comprised of traditionally cambered airfoils, the platform upon which winglets were initially developed. The supercritical wing design is based on that of the Airbus A320, while the conventional airfoil is based upon the Boeing 737-800 platform. Tip devices selected for analysis include blended, raked, split scimitar, fence, and spiroid winglets, as well as tip sails, characterized by the spreading of a bird’s primary flight feathers. Methodology for …

Investigations Of The Negative Temperature Coefficient Region Of Sustainable Aviation Fuels For Mitigation Of Global Warming, Richard C. Smith Iii

Honors College Theses

An investigation was led to determine the correlations between the durations of Ignition Delay (ID), Combustion Delay (CD), Derived Cetane Number (DCN), Negative Temperature Coefficient (NTC), Low-Temperature Heat Release (LTHR) regions, ringing intensity, and precent mass burn, and the effect of blending the Fischer-Tropsch (F-T) synthetic aerospace fuel (SAF), iso-paraffinic kerosene (IPK), with petroleum derived Jet-A aerospace fuel on these regions. Neat blends of Jet-A and IPK and three by mass blends of the fuels will be researched. These blends include mass percentages of 75%Jet-A and 25%IPK (75Jet-A25IPK), 50%Jet-A 50%IPK (50Jet-A50IPK), and 25%Jet-A 75%IPK (25Jet-A75IPK). The study will utilize a …

The Effect Of Fuel Injector Spacing, Angle, And Blowing Ratio On The Fuel Air Mixing Performance Of A Scramjet Engine, Jonathan R. Copeland

Honors College Theses

In the operation of a Scramjet engine, which operates at hypersonic velocities, one of the most important factors is mixing the fuel and air before the high velocity air stream through the engine blows the mixture out of the engine before it could burn. Because of the importance of rapidly mixing fuel and air within a Scramjet engine, there are multiple design elements used to increase mixing. One of which is called a flame holder cavity, which is usually located behind fuel injectors, and designed with an open (length to depth ratio is less than 10) geometry to promote recirculation …

Mechanical Properties Of Nanomodified Hybrid Gfrp Composite Materials, Micah Rop Kimutai

Electronic Theses and Dissertations

The mechanical behavior of the nanomodified hybrid epoxy matrix was investigated in glass fiber reinforced plastics (GFRP). In this study, five nanocomposites enriched with as received halloysite, nanomer I.28E, HNT-APTES, and the hybrid combinations of the two HNTs with the nanomer I.28E were successfully fabricated. To evaluate the effects and morphological characteristics of the individual fillers and the hybrid configurations on the epoxy resin matrix, TGA, DSC, and DMA were analyzed. To understand the effect of the five configurations on the neat GFRP laminate, mode I interlaminar fracture toughness, tensile, and vibration properties were investigated. Electron microscopy testing techniques were …

Experimental And Numerical Investigation Of Naca Airfoil Wing With Winglets, Courtney Danielle Bachmann

Electronic Theses and Dissertations

This research was performed in order to study wingtip devices and, in particular, winglets. Winglets are attached to commercial aircraft for the purpose of reducing induced drag caused by wake vortices on the wingtip. A winglet device can save an aircraft anywhere from 3-7% in fuel consumption. Over the course of a year, this can add up to hundreds of thousands of dollars saved. This research consisted of two parts: one part experiment and one part equipment design. The latter phase of this research examined various methods of testing in a subsonic wind tunnel laboratory setting. Experimental results found with …

An Investigative Study Of Combustion And Emissions With Noise And Vibrations Of Synthetic Fuels Within An Aero-Gas Turbine, Camille J. Phillips

Honors College Theses

The pollution from the aerospace transportation is rapidly becoming the largest source of greenhouse gas (GHG) emissions. The FAA expects aviation emissions to almost triple by 2050, making the aerospace industry responsible for the release of approximately 25% of the global carbon dioxide budget. These aviation emissions, including CO2 and NOx, as well as other GHGs, contribute to the destruction of ozone layer. Carbon dioxide emissions have a particularly negative effect on humans, leading to airway diseases especially in children and elderly. To combat the addition of further GHG emissions into the atmosphere, it is necessary to minimize the usage …

Thermal Performance Of Sierpinski Carpet Fractal Fins At Various Angles Of Inclination In A Natural Convection Environment, Haidar Jamil Khalil

Electronic Theses and Dissertations

As technology advances, higher performance cooling systems are desired to meet numerous thermal management challenges. Extended surfaces, also known as heat sinks or fins, are commonly used to passively dissipate unwanted heat from mechanical and electrical systems. Fractal fins in accordance with the first four iterations (including a base iteration) of the Sierpinski carpet, manufactured from AL-5052, were studied along seven different inclinations from 0° (orientated perpendicular to the direction of gravity) to 90° (orientated parallel to the direction of gravity), in iterations of 15°. The purpose of study was to investigate the thermal performance of the first four fractal …

The Investigation Of Noise, Vibrations And Emissions Of Aero-Gas Turbine Combustion With Synthetic Kerosene Fuels, Margaret Kilpatrick

Honors College Theses

Climatic changes from aviation emissions are complex and include effects of greenhouse gases such as: CO2, NOx, and aerosols. For that reason, the objectives of this study were to investigate the noise, vibrations and emissions characteristics of synthetic kerosene combustion in an aerospace gas turbine to reduce the engine’s environmental impact. Sustainably produced synthetic kerosene is known for having low soot emissions due to little to no aromatics (compounds that create particle pollutants), and for being a sustainable alternative fuel source to imported oil. The noise and sound levels were collected using Bruel & Kjaer microphones to measure various mid …

Ultra-Fast, Autonomous, Reconfigurable Communication System, Paul Bupe Jr

Electronic Theses and Dissertations

The recent years have witnessed an increase in natural disasters in which the destruction of essential communication infrastructure has significantly affected the number of casualties. In 2005, Hurricane Katrina in the United States resulted in over 1,900 deaths, three million land-line phones disconnections, and more than 2000 cell sites going out of service. This incident highlighted an urgent need for a quick-deployment, efficient communication network for emergency relief purposes. In this research, a fully autonomous system to deploy Unmanned Aerial Vehicles (UAVs) as the first phase disaster recovery communication network for wide-area relief is presented. As part of this system, …

Gulfstream Aerospace Aircraft Static Position Utility, Mark Eugene Ray

Legacy ETDs

My research project implements a Java based utility developed for commercial application by Gulfstream Aerospace employees and customers to determine static position data of Gulfstream aircraft. The static position data includes aircraft attitude, nose and main landing gear loads and aircraft ground clearance data.

The previous methods used to obtain this data were a family of spreadsheets. The spreadsheet solution has proven to be awkward and inaccessible for providing the required data. Therefore, Gulfstream Aerospace Management approved the design and implementation of a new aircraft static position utility.

The new utility is identified as the Gulfstream Aircraft Static Position (GASP) …