Engineering Commons^™

Chatgpt As Metamorphosis Designer For The Future Of Artificial Intelligence (Ai): A Conceptual Investigation, Amarjit Kumar Singh (Library Assistant), Dr. Pankaj Mathur (Deputy Librarian)

Library Philosophy and Practice (e-journal)

Abstract

Purpose: The purpose of this research paper is to explore ChatGPT’s potential as an innovative designer tool for the future development of artificial intelligence. Specifically, this conceptual investigation aims to analyze ChatGPT’s capabilities as a tool for designing and developing near about human intelligent systems for futuristic used and developed in the field of Artificial Intelligence (AI). Also with the helps of this paper, researchers are analyzed the strengths and weaknesses of ChatGPT as a tool, and identify possible areas for improvement in its development and implementation. This investigation focused on the various features and functions of ChatGPT that …

Non-Obstetrical Robotic-Assisted Laparoscopic Surgery In Pregnancy: A Systematic Literature Review., Courtney Capella, Joseph Godovchik, Thenappan Chandrasekar, Huda B. Al-Kouatly

Department of Urology Faculty Papers

Urologic and gynecologic surgeons are the top utilizers of robotic surgery; however, non-obstetrical robotic-assisted laparoscopic surgery (RALS) in pregnant patients is infrequent. A systematic literature review was performed to ascertain the frequency, indication and complications of RALS in pregnancy. Results showed thirty-eight pregnancies from eleven publications between 2008-2020. Five cases were for urologic indication and thirty-three for gynecologic indication. Minimal surgical alterations were required. Although no adverse maternal-fetal outcomes were reported, there are not enough cases published to determine safety. This review demonstrates the feasibility of RALS for the pregnant population in the hands of competent robotic surgeons.

Improving 3d Printed Prosthetics With Sensors And Motors, Rachel Zarin

Honors Projects

A 3D printed hand and arm prosthetic was created from the idea of adding bionic elements while keeping the cost low. It was designed based on existing models, desired functions, and materials available. A tilt sensor keeps the hand level, two motors move the wrist in two different directions, a limit switch signals the fingers to open and close, and another motor helps open and close the fingers. All sensors and motors were built on a circuit board, programmed using an Arduino, and powered by a battery. Other supporting materials include metal brackets, screws, guitar strings, elastic bands, small clamps, …

Healthcare Robotics: Key Factors That Impact Robot Adoption In Healthcare, Sujatha Alla, Pilar Pazos

Engineering Management & Systems Engineering Faculty Publications

In the current dynamic business environment, healthcare organizations are focused on improving patient satisfaction, performance, and efficiency. The healthcare industry is considered a complex system that is highly reliant of new technologies to support clinical as well as business processes. Robotics is one of such technologies that is considered to have the potential to increase efficiency in a wide range of clinical services. Although the use of robotics in healthcare is at the early stages of adoption, some studies have shown the capacity of this technology to improve precision, accessibility through less invasive procedures, and reduction of human error during …

Design Of Parallel Robot For Dental Articulation And Its Optimization, Abulimiti Delimulati

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A dental articulator is a mechanical device used to simulate the relative position and motion between the upper and lower jaw when constructing and testing dental prostheses. Typically, it can be adjusted to approximate patient-specific jaw kinematics in order to analogue the static relationship and specific motions of a patient’s mandible to maxilla. However, the use of dental articulators is essentially a trial-and-error method in order to fine-tune fit and function of a dental prosthesis. Some of the most advanced current dental articulators can reproduce the position and the motion passively; furthermore, dentists need special training for measuring patients’ maxillofacial …

Measurement And Description Of Dynamics Required For In Vivo Surgical Robotics Via Kinematic Methods, Jacob G. Greenburg

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

With the goal of improved recovery times and reduced trauma to the patient there has been a substantial shift in the medical community’s demand for minimally invasive surgical (MIS) techniques. With the standardization of MIS becoming more commonplace in the medical field there are still many improvements that are desired. Traditional, manual methods of these surgeries require multiple incisions on the abdomen for the tools and instruments to be inserted. The more recent demand has been to localize the incisions into what is being referred to as a Laparoendoscopic Single-Site (LESS) surgery. Furthermore, the manual instruments that are commonly used …

Procedural Wound Geometry And Blood Flow Generation For Medical Training Simulators, Rifat Aras, Yuzhong Shen, Jiang Li, David R. Holmes Iii (Ed.), Kenneth H. Wong (Ed.)

Electrical & Computer Engineering Faculty Publications

Efficient application of wound treatment procedures is vital in both emergency room and battle zone scenes. In order to train first responders for such situations, physical casualty simulation kits, which are composed of tens of individual items, are commonly used. Similar to any other training scenarios, computer simulations can be effective means for wound treatment training purposes. For immersive and high fidelity virtual reality applications, realistic 3D models are key components. However, creation of such models is a labor intensive process. In this paper, we propose a procedural wound geometry generation technique that parameterizes key simulation inputs to establish the …