Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Institution
Articles 1 - 7 of 7
Full-Text Articles in Engineering
Characterization Of Simulated Low Earth Orbit Space Environment Effects On Acid-Spun Carbon Nanotube Yarns, Ryan A. Kemnitz, Gregory R. Cobb, Abhendra K. Singh, Carl R. Hartsfield
Characterization Of Simulated Low Earth Orbit Space Environment Effects On Acid-Spun Carbon Nanotube Yarns, Ryan A. Kemnitz, Gregory R. Cobb, Abhendra K. Singh, Carl R. Hartsfield
Faculty Publications
The purpose of this study is to quantify the detrimental effects of atomic oxygen and ultraviolet (UV) C radiation on the mechanical properties, electrical conductivity, and piezoresistive effect of acid-spun carbon nanotube (CNT) yarns. Monotonic tensile tests with in-situ electrical resistance measurements were performed on pristine and exposed yarns to determine the effects of the atomic oxygen and UVC exposures on the yarn’s material properties. Both type of exposures were performed under vacuum to simulate space environment conditions. The CNT yarns’ mechanical properties did not change significantly after being exposed to UV radiation, but were significantly degraded by the atomic …
Investigation Of Through Thickness Microstructure And Mechanical Properties In Friction Stir Welded 7n01 Aluminum Alloy Plate, Xingxin Zhao, Zhiyong Yang, Joseph P. Domblesky, Jianmin Han, Zhiqiang Li, Xiaolong Liu
Investigation Of Through Thickness Microstructure And Mechanical Properties In Friction Stir Welded 7n01 Aluminum Alloy Plate, Xingxin Zhao, Zhiyong Yang, Joseph P. Domblesky, Jianmin Han, Zhiqiang Li, Xiaolong Liu
Mechanical Engineering Faculty Research and Publications
An on-going problem in friction stir welded (FSW) joints used in the high-speed train sector is that the microstructure and mechanical properties can significantly vary in thick sections. Because inhomogeneous properties can reduce weld efficiency and degrade service performance, it is of some interest to understand how inhomogeneous properties can develop in FSW welds made from precipitation hardening alloys such as 7N01. In the current study, butt welds were made using 12 mm thick plates and then sectioned perpendicular to the weld line. Five 2.2 mm thick slices were cut from a section and used to measure tensile properties access …
The Effect Of Fine And Coarse Recycled Aggregates On Fresh And Mechanical Properties Of Self-Compacting Concrete, Mahmoud Nili, Hossein Sasanipour, Farhad Aslani
The Effect Of Fine And Coarse Recycled Aggregates On Fresh And Mechanical Properties Of Self-Compacting Concrete, Mahmoud Nili, Hossein Sasanipour, Farhad Aslani
Research outputs 2014 to 2021
Today, the use of recycled aggregates as a substitute for a part of the natural aggregates in concrete production is increasing. This approach is essential because the resources for natural aggregates are decreasing in the world. In the present study, the effects of recycled concrete aggregates as a partial replacement for fine (by 50%) and coarse aggregates (by 100%) were examined in the self-compacting concrete mixtures which contain air-entraining agents and silica fumes. Two series of self-compacting concrete mixes have been prepared. In the first series, fine and coarse recycled mixtures respectively with 50% and 100% replacement with air entraining …
Development Of Heavyweight Self-Compacting Concrete And Ambient-Cured Heavyweight Geopolymer Concrete Using Magnetite Aggregates, Afsaneh Valizadeh, Farhad Aslani, Zohaib Asif, Matt Roso
Development Of Heavyweight Self-Compacting Concrete And Ambient-Cured Heavyweight Geopolymer Concrete Using Magnetite Aggregates, Afsaneh Valizadeh, Farhad Aslani, Zohaib Asif, Matt Roso
Research outputs 2014 to 2021
Heavyweight self-compacting concrete (HWSCC) and heavyweight geopolymer concrete (HWGC) are new types of concrete that integrate the advantages of heavyweight concrete (HWC) with self-compacting concrete (SCC) and geopolymer concrete (GC), respectively. The replacement of natural coarse aggregates with magnetite aggregates in control SCC and control GC at volume ratios of 50%, 75%, and 100% was considered in this study to obtain heavyweight concrete classifications, according to British standards, which provide proper protection from sources that emit harmful radiations in medical and nuclear industries and may also be used in many offshore structures. The main aim of this study is to …
Fire Performance Of Heavyweight Self-Compacting Concrete And Heavyweight High Strength Concrete, Farhad Aslani, Fatemeh Hamidi, Qilong Ma
Fire Performance Of Heavyweight Self-Compacting Concrete And Heavyweight High Strength Concrete, Farhad Aslani, Fatemeh Hamidi, Qilong Ma
Research outputs 2014 to 2021
In this study, the fresh and hardened state properties of heavyweight self-compacting concrete (HWSCC) and heavyweight high strength concrete (HWHSC) containing heavyweight magnetite aggregate with 50, 75, and 100% replacement ratio, and their performance at elevated temperatures were explored experimentally. For fresh-state properties, the flowability and passing ability of HWSCCs were assessed by using slump flow, T500 mm, and J-ring tests. Hardened-state properties including hardened density, compressive strength, and modulus of elasticity were evaluated after 28 days of mixing. High-temperature tests were also performed to study the mass loss, spalling of HWSCC and HWHSC, and residual mechanical properties at 100, …
Mechanical Characterizations Of 3d-Printed Plla/Steel Particle Composites, Hozhabr Mozafari, Pengfei Dong, Haitham Hadidi, Michael P. Sealy, Linxia Gu
Mechanical Characterizations Of 3d-Printed Plla/Steel Particle Composites, Hozhabr Mozafari, Pengfei Dong, Haitham Hadidi, Michael P. Sealy, Linxia Gu
Department of Mechanical and Materials Engineering: Faculty Publications
The objective of this study is to characterize the micromechanical properties of poly-L-lactic acid (PLLA) composites reinforced by grade 420 stainless steel (SS) particles with a specific focus on the interphase properties. The specimens were manufactured using 3D printing techniques due to its many benefits, including high accuracy, cost effectiveness and customized geometry. The adopted fused filament fabrication resulted in a thin interphase layer with an average thickness of 3 μm. The mechanical properties of each phase, as well as the interphase, were characterized by nanoindentation tests. The effect of matrix degradation, i.e., imperfect bonding, on the elastic modulus of …
Effect Of Si And C Additions On The Reaction Mechanism And Mechanical Properties Of Fecrnicu High Entropy Alloy, Hao Wu, Sirui Huang, Huan Qiu, Heguo Zhu, Zonghan Xie
Effect Of Si And C Additions On The Reaction Mechanism And Mechanical Properties Of Fecrnicu High Entropy Alloy, Hao Wu, Sirui Huang, Huan Qiu, Heguo Zhu, Zonghan Xie
Research outputs 2014 to 2021
FeCrNiCu based high entropy alloy matrix composites were fabricated with addition of Si and C by vacuum electromagnetic induction melting. The primary goal of this research was to analyze the reaction mechanism, microstructure, mechanical properties at room temperature and strengthening mechanism of the composites with addition of Si and C. The reaction mechanism of powders containing (Si, Ni and C) was analyzed, only one reaction occurred (i.e., Si + C → SiC) and its activation energy is 1302.8 kJ/mol. The new composites consist of a face centered cubic (FCC) structured matrix reinforced by submicron sized SiC particles. The addition of …