Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 30 of 30
Full-Text Articles in Engineering
High-Temperature Piezoelectric Sensing, Xiaoning Jiang, Kyungrim Kim, Shujun Zhang, Joseph A. Johnson, Giovanni Salazar
High-Temperature Piezoelectric Sensing, Xiaoning Jiang, Kyungrim Kim, Shujun Zhang, Joseph A. Johnson, Giovanni Salazar
Australian Institute for Innovative Materials - Papers
Piezoelectric sensing is of increasing interest for high-temperature applications in aerospace, automotive, power plants and material processing due to its low cost, compact sensor size and simple signal conditioning, in comparison with other high-temperature sensing techniques. This paper presented an overview of high-temperature piezoelectric sensing techniques. Firstly, different types of high-temperature piezoelectric single crystals, electrode materials, and their pros and cons are discussed. Secondly, recent work on high-temperature piezoelectric sensors including accelerometer, surface acoustic wave sensor, ultrasound transducer, acoustic emission sensor, gas sensor, and pressure sensor for temperatures up to 1,250 °C were reviewed. Finally, discussions of existing challenges and …
1-3 Piezoelectric Composites For High-Temperature Transducer Applications, Lili Li, Shujun Zhang, Zhuo Xu, Fei Wen, Xuecang Geng, Hyeong Jae Lee, Thomas R. Shrout
1-3 Piezoelectric Composites For High-Temperature Transducer Applications, Lili Li, Shujun Zhang, Zhuo Xu, Fei Wen, Xuecang Geng, Hyeong Jae Lee, Thomas R. Shrout
Australian Institute for Innovative Materials - Papers
High-temperature Pb(Zr,Ti)O3/epoxy 1-3 composites were fabricated using the dice and fill method. The epoxy filler was modified with glass spheres in order to improve the thermal reliability of the composites at elevated temperatures. Temperature-dependent dielectric and electromechanical properties of the composites were measured after ageing at 250 °C with different dwelling times. Obvious cracks were observed and the electrodes were damaged in the composite with unmodified epoxy after 200 h, leading to the failure of the composite. In contrast, composites with >12 vol% glass sphere loaded epoxies were found to exhibit minimal electrical property variation after ageing for 500 h, …
Synergetic Combination Of Limd With Chpd For The Production Of Economical And High Performance Mgb2 Wires, Minoru Maeda, Md Shahriar Ai Hossain, Ashkan Motaman, Jung Ho Kim, Anna Kario, Matt Rindfleisch, Mike Tomsic, S X. Dou
Synergetic Combination Of Limd With Chpd For The Production Of Economical And High Performance Mgb2 Wires, Minoru Maeda, Md Shahriar Ai Hossain, Ashkan Motaman, Jung Ho Kim, Anna Kario, Matt Rindfleisch, Mike Tomsic, S X. Dou
Australian Institute for Innovative Materials - Papers
We propose an economical fabrication concept, the localized internal magnesium diffusion (IMD) method. Instead of using a single magnesium (Mg) rod in the center of a metal sheath tube, we use large-sized Mg particles (20-50 mesh) mixed well with cheap 97% crystalline boron powder to fill the metal sheath tube. After a repeated drawing process, the coarse Mg is elongated along the core wire axis of the metal sheath tube. Textured MgB2 grains are then formed during the sintering process. In the localized IMD process, however, there is still a need to improve the overall density. In order to increase …
Tensile Testing Of Individual Glassy, Rubbery And Hydrogel Electrospun Polymer Nanofibres To High Strain Using The Atomic Force Microscope, Adrian Gestos, Philip G. Whitten, Geoffrey M. Spinks, Gordon G. Wallace
Tensile Testing Of Individual Glassy, Rubbery And Hydrogel Electrospun Polymer Nanofibres To High Strain Using The Atomic Force Microscope, Adrian Gestos, Philip G. Whitten, Geoffrey M. Spinks, Gordon G. Wallace
Australian Institute for Innovative Materials - Papers
The production and use of polymer nanofibre assemblies prepared by electrospinning is now widespread. It is known that the tensile properties of electrospun polymer fibres can be different to those of bulk polymers. Here, we report a general method for measuring the tensile properties of individual electrospun nanofibres that employs a commercial atomic force microscope. Methods for preparing samples, force calibration and calculation of tensile stress and strain are described along with error estimation. By appropriate choice of AFM cantilever, it is shown that the tensile stress-strain curves can be measured for glassy, rubbery and gel polymer nanofibres. Testing can …
A Significant Improvement In Both Low- And High-Field Performance Of Mgb2 Superconductors Through Graphene Oxide Doping, K S B De Silva, S H Aboutalebi, Xun Xu, Xiaolin Wang, W X Li, Konstantin Konstantinov, S X. Dou
A Significant Improvement In Both Low- And High-Field Performance Of Mgb2 Superconductors Through Graphene Oxide Doping, K S B De Silva, S H Aboutalebi, Xun Xu, Xiaolin Wang, W X Li, Konstantin Konstantinov, S X. Dou
Australian Institute for Innovative Materials - Papers
The effects of graphene oxide (GO) doping on the superconducting properties of MgB2 were studied using bulk samples made by the diffusion method. Homogeneous dispersions of GO in tetrahydrofuran were obtained through a novel synthesis method, which is then chemically doped with MgB2. It was found that GO doping significantly improves the critical current density, under both low and high magnetic fields, which distinguishes GO from all the other elements doped into MgB2 so far. 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
Extrusion Printing Of Ionic-Covalent Entanglement Hydrogels With High Toughness, Shannon Bakarich, Marc In Het Panhuis, Stephen T. Beirne, Gordon G. Wallace, Geoffrey Maxwell Spinks
Extrusion Printing Of Ionic-Covalent Entanglement Hydrogels With High Toughness, Shannon Bakarich, Marc In Het Panhuis, Stephen T. Beirne, Gordon G. Wallace, Geoffrey Maxwell Spinks
Australian Institute for Innovative Materials - Papers
Three-dimensional (3D) printing of hydrogels has recently been investigated for use in tissue engineering applications. One major limitation in the use of synthetic hydrogels is their poor mechanical robustness but the development of ‘tough hydrogels’ in conjunction with additive fabrication techniques will accelerate the advancement of many technologies including soft robotics, bionic implants, sensors and controlled release systems. This article demonstrates that ionic–covalent entanglement (ICE) gels can be fabricated through a modified extrusion printing process that facilitates in situ photopolymerisation. The rheological properties of alginate–acrylamide hydrogel precursor solutions were characterised to develop formulations suitable for extrusion printing. A range of …
Cell Attachment And Proliferation On High Conductivity Pedot-Glycol Composites Produced By Vapour Phase Polymerisation, Elise M. Stewart, Manrico Fabretto, Mischa Mueller, Paul J. Molino, Hans J. Griesser, Robert D. Short, Gordon G. Wallace
Cell Attachment And Proliferation On High Conductivity Pedot-Glycol Composites Produced By Vapour Phase Polymerisation, Elise M. Stewart, Manrico Fabretto, Mischa Mueller, Paul J. Molino, Hans J. Griesser, Robert D. Short, Gordon G. Wallace
Australian Institute for Innovative Materials - Papers
High conductivity poly(3,4-ethylene dioxythiophene) (PEDOT) was synthesised using vacuum vapour phase polymerization (VVPP). The process produces PEDOT composites which incorporate glycol within the polymer. To assess biocompatibility, a suite of analytical techniques were utilised in an effort to characterise the level of glycol present and its impact on cell attachment and proliferation. A small decrease in fibroblast cell attachment and proliferation was observed with increasing glycol content within the PEDOT composite. Keratinocyte cell attachment and proliferation by comparison showed an increase. As such, the results herein indicate that cell attachment and proliferation depends on the individual cell lines used and …
Graphene Micro-Substrate Induced High Electron-Phonon Coupling In Mgb2, W X. Li, X Xu, K S. B De Silva, F X. Xiang, S X. Dou
Graphene Micro-Substrate Induced High Electron-Phonon Coupling In Mgb2, W X. Li, X Xu, K S. B De Silva, F X. Xiang, S X. Dou
Faculty of Engineering and Information Sciences - Papers: Part A
Electron-phonon coupling strength was studied in graphene-MgB2 composites to explore the possibilities for a higher superconducting transition temperature (Tc). For the first time in the experimental work on MgB2, the Raman active E2g mode was split into two parts: a softened mode corresponding to tensile strain and a hardened mode attributed to the carbon substitution effect. The tensile strain effect is suggested to improve Tc of graphene-MgB2 composites because it increases the electron-phonon coupling strength of MgB2.
High-Throughput Particle Manipulation By Hydrodynamic, Electrokinetic, And Dielectrophoretic Effects In An Integrated Microfluidic Chip, Shunbo Li, Ming Li, Kristelle Bougot-Robin, Wenbin Cao, Irene Yeung Chau, Weihua Li, Weijia Wen
High-Throughput Particle Manipulation By Hydrodynamic, Electrokinetic, And Dielectrophoretic Effects In An Integrated Microfluidic Chip, Shunbo Li, Ming Li, Kristelle Bougot-Robin, Wenbin Cao, Irene Yeung Chau, Weihua Li, Weijia Wen
Faculty of Engineering and Information Sciences - Papers: Part A
Integrating different steps on a chip for cell manipulations and sample preparation is of foremost importance to fully take advantage of microfluidic possibilities, and therefore make tests faster, cheaper and more accurate. We demonstrated particle manipulation in an integrated microfluidic device by applying hydrodynamic, electroosmotic (EO), electrophoretic (EP), and dielectrophoretic (DEP) forces. The process involves generation of fluid flow by pressure difference, particle trapping by DEP force, and particle redirect by EO and EP forces. Both DC and AC signals were applied, taking advantages of DC EP, EO and AC DEP for on-chip particle manipulation. Since different types of particles …
Dynamic Testing Of Tekseal High Yield Grout To Provide An Orepass Plug Designed For Impact, I V. S Mutton, Alexander Remennikov, D Pateman
Dynamic Testing Of Tekseal High Yield Grout To Provide An Orepass Plug Designed For Impact, I V. S Mutton, Alexander Remennikov, D Pateman
Faculty of Engineering and Information Sciences - Papers: Part A
Significant wear in orepasses particularly in the brow and chute areas is proportional to the tonnage throughput with increased wear associated with running orepasses empty. During planned shutdowns it may be necessary to isolate maintenance crews from objects falling from orepasses. In the last 15 years grout orepass plugs that can later be easily removed have been poured above chute maintenance areas. These provide protection from high energy impact and isolating workers from the hazard. Construction and removal methods will be briefly explained. Since it is not feasible to investigate the problem of orepass plug impact response using full-scale experimental …
A High Performance Peer To Cloud And Peer Model Augmented With Hierarchical Secure Communications, Zhe Sun, Jun Shen
A High Performance Peer To Cloud And Peer Model Augmented With Hierarchical Secure Communications, Zhe Sun, Jun Shen
Faculty of Engineering and Information Sciences - Papers: Part A
This paper presents a secure storage model named Peer to Cloud and Peer (P2CP). P2CP uses the cloud storage system as a backbone storage system. However, when data transmission occurs, the data nodes, cloud user, and the non-cloud user are involved to complete the transaction all together. The users, typically the client peers, can communicate with each other directly, thus bypassing servers on the cloud. Similarly, cloud servers can communicate with each other in a P2P mode. We also introduce a "hierarchy security" method to guarantee the data security in the proposed P2CP storage model. A key feature of our …
Development Of Safe Optimized Welding Procedures For High Strength Q&T Steel Welded With Austenitic Consumables, Lenka Kuzmikova, Huijun Li, John Norrish, Zengxi Stephen Pan, Nathan Larkin
Development Of Safe Optimized Welding Procedures For High Strength Q&T Steel Welded With Austenitic Consumables, Lenka Kuzmikova, Huijun Li, John Norrish, Zengxi Stephen Pan, Nathan Larkin
Faculty of Engineering and Information Sciences - Papers: Part A
High strength quenched and tempered (Q&T) steels offer obvious economic benefits originating from their advantageous strength to price and weight ratios. These steels are usually welded using ferritic consumables and for this combination the risk of hydrogen assisted cold cracking (HACC) is high. The use of austenitic stainless steel (ASS) consumables has great potential to significantly improve this issue. Yet, there are no guidelines for determination of safe level of preheat for welding ferritic steels with ASS consumables. For this reason manufacturers adopt this parameter from procedures developed for conventional ferritic consumables thus significantly limiting the benefits ASS consumables are …
The Feasibility Study And Characterziation Of A Two-Dimensional Diode Array In “Magic Phantom” For High Dose Rate Brachytherapy Quality Assurance, A Espinoza, B Beeksma, M Petasecca, I Fuduli, C Porumb, D L. Cutajar, S Corde, M A. Jackson, M Lf Lerch, Anatoly B. Rosenfeld
The Feasibility Study And Characterziation Of A Two-Dimensional Diode Array In “Magic Phantom” For High Dose Rate Brachytherapy Quality Assurance, A Espinoza, B Beeksma, M Petasecca, I Fuduli, C Porumb, D L. Cutajar, S Corde, M A. Jackson, M Lf Lerch, Anatoly B. Rosenfeld
Faculty of Engineering and Information Sciences - Papers: Part A
High dose rate (HDR) brachytherapy is a radiation treatment technique capable of delivering large dose rates to the tumor. Radiation is delivered using remote afterloaders to drive highly active sources (commonly 192Ir with an air KERMA strength range between 20 000 and 40 000 U, where 1 U = 1 uGy m2/h in air) through applicators directly into the patient's prescribed region of treatment. Due to the obvious ramifications of incorrect treatment while using such an active source, it is essential that there are methods for quality assurance (QA) that can directly and accurately verify the treatment plan and the …
A Unique Sandwich-Structured C/Ge/Graphene Nanocomposite As An Anode Material For High Power Lithium Ion Batteries, Dan Li, Kuok H. Seng, Dongqi Shi, Zhixin Chen, Hua-Kun Liu, Zaiping Guo
A Unique Sandwich-Structured C/Ge/Graphene Nanocomposite As An Anode Material For High Power Lithium Ion Batteries, Dan Li, Kuok H. Seng, Dongqi Shi, Zhixin Chen, Hua-Kun Liu, Zaiping Guo
Faculty of Engineering and Information Sciences - Papers: Part A
A unique sandwich-structured C/Ge/graphene composite with germanium nanoparticles trapped between graphene sheets is prepared by a microwave-assisted solvothermal reaction followed by carbon coating and thermal reduction. The graphene sheets are found to be effective in hindering the growth and aggregation of GeO2 nanoparticles. More importantly, the graphene sheets, coupled with the carbon coating, can buffer the volume changes of germanium in electrochemical lithium reactions. The unique sandwich structure features a highly conductive network of carbon, which can improve both the conductivity and the structural stability of the electrode material, and exemplifies a promising strategy for the development of new high …
Transmit Antenna Subset Selection With Power Balancing For High Data Rate Mimo-Ofdm Uwb Systems, Ngoc Phuc Le, Le Chung Tran, Farzad Safaei
Transmit Antenna Subset Selection With Power Balancing For High Data Rate Mimo-Ofdm Uwb Systems, Ngoc Phuc Le, Le Chung Tran, Farzad Safaei
Faculty of Engineering and Information Sciences - Papers: Part A
This paper proposes per-subcarrier transmit antenna subset selection with power balancing for MIMO-OFDM UWB systems to simultaneously improve the system error performance and increase data rates. The deployment of the per-subcarrier antenna subset selection may result in a power unbalance across antennas, which could cause power amplifiers (PAs) to operate in their non-linear regions. To overcome this disadvantage, we formulate a linear optimization problem for the optimal allocation of data subcarriers under a constraint that all antennas have the same number of assigned data symbols. This optimization problem could be applied to systems with an arbitrary number of multiplexed data …
Improving The Critical Speeds Of High-Speed Trains Using Magnetorheological Technology, Shuaishuai Sun, Huaxia Deng, Weihua Li, Haiping Du, Yi Qing Ni, Jin Zhang, Jian Yang
Improving The Critical Speeds Of High-Speed Trains Using Magnetorheological Technology, Shuaishuai Sun, Huaxia Deng, Weihua Li, Haiping Du, Yi Qing Ni, Jin Zhang, Jian Yang
Faculty of Engineering and Information Sciences - Papers: Part A
With the rapid development of high-speed railways, vibration control for maintaining stability, passenger comfort, and safety has become an important area of research. In order to investigate the mechanism of train vibration, the critical speeds of various DOFs with respect to suspension stiffness and damping are first calculated and analyzed based on its dynamic equations. Then, the sensitivity of the critical speed is studied by analyzing the influence of different suspension parameters. On the basis of these analyses, a conclusion is drawn that secondary lateral damping is the most sensitive suspension damper. Subsequently, the secondary lateral dampers are replaced with …
Spherical, Cylindrical And Tetrahedral Symmetries; Hydrogenic States At High Magnetic Field In Si:P, R A. Lewis, A Bruno-Alfonso, G V B De Souza, R E M Vickers, J A Colla, E Constable
Spherical, Cylindrical And Tetrahedral Symmetries; Hydrogenic States At High Magnetic Field In Si:P, R A. Lewis, A Bruno-Alfonso, G V B De Souza, R E M Vickers, J A Colla, E Constable
Faculty of Engineering and Information Sciences - Papers: Part A
Phosphorous donors in silicon have an electronic structure that mimics the hydrogen atom, albeit on a larger length, smaller energy and smaller magnetic field scale. While the hydrogen atom is spherically symmetric, an applied magnetic field imposes cylindrical symmetry, and the solid-state analogue involves, in addition, the symmetry of the Si crystal. For one magnetic field direction, all six conduction-band valleys of Si:P become equivalent. New experimental data to high laboratory fields (30 T), supported by new calculations, demonstrate that this high symmetry field orientation allows the most direct comparison with free hydrogen.
Online In Vivo Dosimetry In High Dose Rate Prostate Brchytherapy With Moskin Detectors: In Phantom Feasibility Study, G Gambarini, M Carrara, C Tenconi, N Mantaut, M Borroni, D Cutajar, M Petasecca, I Fuduli, M Lerch, E Pignoli, Anatoly B. Rosenfeld
Online In Vivo Dosimetry In High Dose Rate Prostate Brchytherapy With Moskin Detectors: In Phantom Feasibility Study, G Gambarini, M Carrara, C Tenconi, N Mantaut, M Borroni, D Cutajar, M Petasecca, I Fuduli, M Lerch, E Pignoli, Anatoly B. Rosenfeld
Faculty of Engineering and Information Sciences - Papers: Part A
MOSkin detectors were studied to perform real-time in vivo dose measurements in high dose rate prostate brachytherapy. Measurements were performed inside an urethral catheter in a gel phantom simulating a real prostate implant. Measured and expected doses were compared and the discrepancy was found to be within 8.9% and 3.8% for single MOSkin and dual-MOSkin configurations, respectively. Results show that dual-MOSkin detectors can be profitably adopted in prostate brachytherapy treatments to perform real-time in vivo dosimetry inside the urethra.
The Asian Evolution Of High Speed Rail, Philip G. Laird
The Asian Evolution Of High Speed Rail, Philip G. Laird
Faculty of Engineering and Information Sciences - Papers: Part A
In Australia, in 2001, the Howard government released an East Coast HSR Scoping Study. This followed two major investigations by the private sector into HSR options for Australia; the first being a Sydney Canberra Melbourne Very Fast Train as proposed in 1984 by CSIRO, and the second being the Sydney Canberra Speed HSR proposal.
A Scalable Unsupervised Feature Merging Approach To Efficient Dimensionality Reduction Of High-Dimensional Visual Data, Lingqiao Liu, Lei Wang
A Scalable Unsupervised Feature Merging Approach To Efficient Dimensionality Reduction Of High-Dimensional Visual Data, Lingqiao Liu, Lei Wang
Faculty of Engineering and Information Sciences - Papers: Part A
To achieve a good trade-off between recognition accuracy and computational efficiency, it is often needed to reduce high-dimensional visual data to medium-dimensional ones. For this task, even applying a simple full-matrix-based linear projection causes significant computation and memory use. When the number of visual data is large, how to efficiently learn such a projection could even become a problem. The recent feature merging approach offers an efficient way to reduce the dimensionality, which only requires a single scan of features to perform reduction. However, existing merging algorithms do not scale well with high-dimensional data, especially in the unsupervised case. To …
Parametric Study On Chain-Die Forming For Advanced High Strength Steels, Yuankun Zhang, Shichao Ding
Parametric Study On Chain-Die Forming For Advanced High Strength Steels, Yuankun Zhang, Shichao Ding
Faculty of Engineering and Information Sciences - Papers: Part A
As the applications of AHSS for the automotive industry are increasing significantly within the last decade, it becomes more and more important to develop a new forming technology as an alternative or even a replacement to roll forming to overcome the difficulties and problems of manufacturing the AHSS parts. The springback of the material with higher strength and thinner thickness becomes more difficult to predict, which directly affects the application of roll forming in AHSS. Chain-die forming, as an alternative to roll forming proposed and developed recently in Australia, is expected to be a solution to the problems addressed. It …
Multi-Factor Coupling System Characteristic Of The Dynamic Roll Gap In The High-Speed Rolling Mill During The Unsteady Lubrication Process, Qiaoyi Wang, Zhengyi Jiang, Jingwei Zhao, Min Fang
Multi-Factor Coupling System Characteristic Of The Dynamic Roll Gap In The High-Speed Rolling Mill During The Unsteady Lubrication Process, Qiaoyi Wang, Zhengyi Jiang, Jingwei Zhao, Min Fang
Faculty of Engineering and Information Sciences - Papers: Part A
In the present work, a multi-factor coupling dynamic model of a rolling mill system for a dynamic roll gap during an unsteady lubrication process was developed on the basis of the rolling theory, lubrication and the friction theory, and the mechanical vibration theory. The multi-factor coupling model of interfacial film binding was coupled with the rolling force model, dynamic roll gap interface friction model and work roll movement model. The corresponding distributions of friction and pressure at varying surface roughness and times were systematically analyzed during the unsteady mixed lubrication process. The effects of the main processing parameters on the …
An Investigation Into Electron Scattering From Pyrazine At Intermediate And High Energies, A G. Sanz, M C. Fuss, Francisco Blanco, J D. Gorfinkiel, D Almeida, F. Ferreira Da Silva, P Limao-Vieira, M J. Brunger, G Garcia
An Investigation Into Electron Scattering From Pyrazine At Intermediate And High Energies, A G. Sanz, M C. Fuss, Francisco Blanco, J D. Gorfinkiel, D Almeida, F. Ferreira Da Silva, P Limao-Vieira, M J. Brunger, G Garcia
Faculty of Engineering and Information Sciences - Papers: Part A
Total electron scattering cross sections for pyrazine in the energy range 10-500 eV have been measured with a new magnetically confined electron transmission-beam apparatus. Theoretical differential and integral elastic, as well as integral inelastic, cross sections have been calculated by means of a screening-corrected form of the independent-atom representation (IAM-SCAR) from 10 to 1000 eV incident electron energies. The present experimental and theoretical total cross sections show a good level of agreement, to within 10%, in the overlapping energy range. Consistency of these results with previous calculations (i.e., the R-matrix and Schwinger Multichannel methods) and elastic scattering measurements at lower …
Free-Standing Nanocomposites With High Conductivity And Extensibility, Kyoung-Yong Chun, Shi Hyeong Kim, Min Kyoon Shin, Youn Tae Kim, Geoffrey M. Spinks, Ali E. Aliev, Ray H. Baughman, Seon Jeong Kim
Free-Standing Nanocomposites With High Conductivity And Extensibility, Kyoung-Yong Chun, Shi Hyeong Kim, Min Kyoon Shin, Youn Tae Kim, Geoffrey M. Spinks, Ali E. Aliev, Ray H. Baughman, Seon Jeong Kim
Faculty of Engineering and Information Sciences - Papers: Part A
The prospect of electronic circuits that are stretchable and bendable promises tantalizing applications such as skin-like electronics, roll-up displays, conformable sensors and actuators, and lightweight solar cells. The preparation of highly conductive and highly extensible materials remains a challenge for mass production applications, such as free-standing films or printable composite inks. Here we present a nanocomposite material consisting of carbon nanotubes, ionic liquid, silver nanoparticles, and polystyrene- polyisoprene-polystyrene having a high electrical conductivity of 3700 S cm -1 that can be stretched to 288% without permanent damage. The material is prepared as a concentrated dispersion suitable for simple processing into …
On-Chip High Sensitivity Laser Frequency Sensing With Brillouin Mutually-Modulated Cross-Gain Modulation, Feng Gao, R Pant, Enbang Li, Christopher G. Poulton, D Choi, Stephen J. Madden, B Luther-Davies, Benjamin Eggleton
On-Chip High Sensitivity Laser Frequency Sensing With Brillouin Mutually-Modulated Cross-Gain Modulation, Feng Gao, R Pant, Enbang Li, Christopher G. Poulton, D Choi, Stephen J. Madden, B Luther-Davies, Benjamin Eggleton
Faculty of Engineering and Information Sciences - Papers: Part A
We report the first demonstration of a photonic-chip laser frequency sensor using Brillouin mutually-modulated cross-gain modulation (MMXGM). A large sensitivity (∼9.5 mrad/kHz) of the modulation phase shift to probe carrier frequency is demonstrated at a modulation frequency of 50 kHz using Brillouin MMXGM in a ∼7 cm long chalcogenide rib waveguide. © 2013 Optical Society of America.
Addressing Retained Austenite Stability In Advanced High Strength Steels, Elena V. Pereloma, Azdiar A. Gazder, Ilana B. Timokhina
Addressing Retained Austenite Stability In Advanced High Strength Steels, Elena V. Pereloma, Azdiar A. Gazder, Ilana B. Timokhina
Faculty of Engineering and Information Sciences - Papers: Part A
Advances in the development of new high strength steels have resulted in microstructures containing significant volume fractions of retained austenite. The transformation of retained austenite to martensite upon straining contributes towards improving the ductility. However, in order to gain from the above beneficial effect, the volume fraction, size, morphology and distribution of the retained austenite need to be controlled. In this regard, it is well known that carbon concentration in the retained austenite is responsible for its chemical stability, whereas its size and morphology determines its mechanical stability. Thus, to achieve the required mechanical properties, control of the processing parameters …
A Hybrid Electrolyte Energy Storage Device With High Energy And Long Life Using Lithium Anode And Mno2 Nanoflake Cathode, Shulei Chou, Yun-Xiao Wang, Jiantie Xu, Jia-Zhao Wang, Hua-Kun Liu, S X. Dou
A Hybrid Electrolyte Energy Storage Device With High Energy And Long Life Using Lithium Anode And Mno2 Nanoflake Cathode, Shulei Chou, Yun-Xiao Wang, Jiantie Xu, Jia-Zhao Wang, Hua-Kun Liu, S X. Dou
Australian Institute for Innovative Materials - Papers
A hybrid electrolyte energy storage system combining the features of supercapacitors and lithium batteries has been constructed. It consists of MnO2 nanoflakes in 1 M Li2SO4 aqueous electrolyte as the cathode and lithium foil in ionic liquid (1 M lithium bis(trifluoromethanesulfonyl)imide (LiNTf2) in N-methyl-N-propyl pyrrolidinium bis(trifluoromethanesulfonyl)imide ([C(3)mpyr][NTf2])) electrolyte as the anode, separated by a lithium super ionic conductor glass ceramic film (LiSICON). This system shows the advantages of both a supercapacitor (long cycle life) and a lithium battery (high energy), as well as low cost and improved safety due to the combination of ionic liquid and ceramic solid state electrolyte …
High Strain Stretchable Solid Electrolytes, Sureyya Saricilar, Dennis Antiohos, Kewei Shu, Philip G. Whitten, Klaudia Wagner, Caiyun Wang, Gordon G. Wallace
High Strain Stretchable Solid Electrolytes, Sureyya Saricilar, Dennis Antiohos, Kewei Shu, Philip G. Whitten, Klaudia Wagner, Caiyun Wang, Gordon G. Wallace
Australian Institute for Innovative Materials - Papers
Wearable electronic devices that can be integrated seamlessly into clothing for monitoring and feedback need to be not only flexible, but also stretchable with low stiffness. Currently there are few solid electrolytes that are sufficiently stretchable for wearable electronic devices. Here we report stretchable solid electrolytes that can be elastically stretched more than 500% of their original length with ionic conductivities as high as 7 x 10(-5) S cm(-1) and tensile breaking strengths larger than 1.5 MPa. These solid electrolytes consist of poly(methyl methacrylate) chemical networks solvated by an electrochemically stable ionic liquid. A stretchable supercapacitor was demonstrated by coating …
The Electrochemical Properties Of High-Capacity Sulfur/Reduced Graphene Oxide With Different Electrolyte Systems, Yunxiao Wang, Shulei Chou, Hua-Kun Liu, S X. Dou
The Electrochemical Properties Of High-Capacity Sulfur/Reduced Graphene Oxide With Different Electrolyte Systems, Yunxiao Wang, Shulei Chou, Hua-Kun Liu, S X. Dou
Australian Institute for Innovative Materials - Papers
The lithium/sulfur battery is a promising electrochemical system with high capacity, which is well-known to undergo a complex multistep reaction during the discharge process. Two types of electrolytes including poly (ethylene glycol) dimethyl ether (PEGDME)-based and 1.3 - dioxolane (DOL)/ dimethoxyethane (DME)-based electrolytes were investigated here. Furthermore, LiNO3 additive was introduced into the electrolyte in order to effectively eliminate the overcharge effect. The lithium sulfur battery with 1.0 M LiN(CF3SO2)2 in PEGME with 0.1 M LiNo3 shows highly stable reversible capacity of 624.8 mAh g-1 after 200 cycles and improved average coulombic efficiency of 98 percent.
Removal Of Na+ From Ionic Liquids By Zeolite For High Quality Electrolyte Manufacture, Won-Je Cho, Yongseong Seo, Soon Jae Jung, Won-Gil Lee, Byung Chul Kim, Grant A. Mathieson, Kook Hyun Yu
Removal Of Na+ From Ionic Liquids By Zeolite For High Quality Electrolyte Manufacture, Won-Je Cho, Yongseong Seo, Soon Jae Jung, Won-Gil Lee, Byung Chul Kim, Grant A. Mathieson, Kook Hyun Yu
Australian Institute for Innovative Materials - Papers
This study develops a novel method to remove the free cations created during the synthesis of ionic liquid. The cations are removed from the ionic liquid by size-selective adsorption onto chemically surface-modified Zeolite. The porous crystal nano-structure of Zeolite has several electron-rich Al sites to attract cations. While large cations of an ionic liquid cannot access the Zeolite nano-structure, small cations like Na+ have ready access and are adsorbed. This study confirms that: Na+ can be removed from ionic liquid effectively using Zeolite; and, in contrast to the conventional and extensively applied ion exchange resin method or solvent extraction methods, …