Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 9 of 9
Full-Text Articles in Engineering
Effect Of Ti And N Concentrations On Microstructure And Mechanical Properties Of Microalloyed High Strength Line Pipe Steel Welds, Leigh Fletcher, Zhixiong Zhu, Marimuthu Murugananth, Lei Zheng, Mingzhuo Bai, Huijun Li, F Barbaro
Effect Of Ti And N Concentrations On Microstructure And Mechanical Properties Of Microalloyed High Strength Line Pipe Steel Welds, Leigh Fletcher, Zhixiong Zhu, Marimuthu Murugananth, Lei Zheng, Mingzhuo Bai, Huijun Li, F Barbaro
Faculty of Engineering - Papers (Archive)
A selection of nine heats of line pipe steel from the same project with different Ti and N content were used to evaluate the effects of Ti/N ratio on weld zone microstructure, hardness and prior austenite grain size (PAGS) in the coarse grained heat-affected zone (CGHAZ). It was shown that the microstructure of the base metal (BM) mainly consisted of fine grained polygonal ferrite with fine islands of pearlite. The weld metal (WM) microstructure was predominantly acicular ferrite with a small volume fraction of pro-eutectoid ferrite. The CGHAZ consisted of bainitic ferrite and islands of martensite-austenite. The inside region of …
Sensitization Behaviour Of 11-12% Cr Aisi 409 Stainless Steel During Low Heat Input Welding, Cornelis Janise Van Niekerk, Madeleine Du Toit
Sensitization Behaviour Of 11-12% Cr Aisi 409 Stainless Steel During Low Heat Input Welding, Cornelis Janise Van Niekerk, Madeleine Du Toit
Faculty of Engineering and Information Sciences - Papers: Part A
The study comprised of the investigation into the sensitization characteristics of AISI 409 titanium stabilized ferritic stainless steel during low heat input welding. AISI 409 is a fully ferritic stainless steel used in catalytic converters and tubing for automotive exhaust systems due to the supposition that sensitization does not occur during low heat input welding. Two plates of 2 and 4 mm were tested for sensitization during low heat input welding. The study confirmed that chromium carbide (M23C6) precipitation occurs on the grain boundaries in the heat-affected zone with consequent depletion of Cr adjacent to the …
Development Of A Dc-Lsnd Welding Process For Gmaw On Dh-36 Steel, Raymond Holder, Nathan Larkin, Huijun Li, Lenka Kuzmikova, Zengxi Pan, John Norrish
Development Of A Dc-Lsnd Welding Process For Gmaw On Dh-36 Steel, Raymond Holder, Nathan Larkin, Huijun Li, Lenka Kuzmikova, Zengxi Pan, John Norrish
Faculty of Engineering and Information Sciences - Papers: Part A
Weld induced distortion correction is a major cost within the shipbuilding industry. This paper investigates the use of an active cooling process known as Dynamically Controlled - Low Stress No Distortion (DC-LSND) Welding on DH-36 steel. Thermal profiles are obtained and distortion measurements are also achieved. Results show that the application of a localised cryogenic cooling source trailing the welding arc can significantly reduce weld induced distortion using the GMAW process. The effect of forced cooling on the weld microstructure is also observed.
Research To Establish A Systematic Approach To Safe Welding Procedure Development Using Austenitic Filler Material For Fabrication Of High Strength Steel, Lenka Kuzmikova, John Norrish, Huijun Li, Mark Callaghan
Research To Establish A Systematic Approach To Safe Welding Procedure Development Using Austenitic Filler Material For Fabrication Of High Strength Steel, Lenka Kuzmikova, John Norrish, Huijun Li, Mark Callaghan
Faculty of Engineering and Information Sciences - Papers: Part A
High strength, thermo-mechanically treated steels often require very careful control of welding procedures to ensure freedom from hydrogen assisted cold cracking (HACC) in the weld metal and heat affected zone (HAZ) whilst avoiding undue loss of heat affected zone strength. In practice this leads to restricted operating envelopes and the requirement for rigorous procedure management. An alternative approach is the use of austenitic welding consumables but whilst this may be expected to expand the process parameter envelope its use is often restricted by adherence to procedures previously developed for ferritic consumables. The current paper describes the research undertaken to establish …
Self-Shape Optimisation Of Cold-Formed Steel Closed Profiles Using Genetic Algorithms, Benoit Gilbert, Lip H. Teh, Hong Guan
Self-Shape Optimisation Of Cold-Formed Steel Closed Profiles Using Genetic Algorithms, Benoit Gilbert, Lip H. Teh, Hong Guan
Faculty of Engineering and Information Sciences - Papers: Part A
For economical benefits, optimisation of mass-produced structural steel products is widely researched. The objective is to minimise the quantity of material used without sacrificing the strength and practicality of the structural members. Current research focuses on optimising the dimensions of conventional cross-sectional shapes but rarely considers discovering new optimum shapes. This report introduces the concepts of a new optimisation method which enables the crosssection to self-shape to an optimum by using the evolution and adaptation benefits of Genetic Algorithm. The feasibility and accuracy of the method are verified by implementing it to find optimum thin-walled profiles against simple parameters for …
The Influence Of Copper Content Of Welding Wires On The Fume Formation Rates In Gas Metal Arc Welding Of Steel, N Bothma, B J. Monaghan, J Norrish
The Influence Of Copper Content Of Welding Wires On The Fume Formation Rates In Gas Metal Arc Welding Of Steel, N Bothma, B J. Monaghan, J Norrish
Faculty of Engineering - Papers (Archive)
Increases in Fume Formation Rates (FFR) of welding wires have been attributed to the fact that wires are copper coated. Instability during the welding process can have an influence on the FFR. The University of Wollongong has developed an auto control mechanism that will minimise the influence of the instability and this could be applied to more accurately determine the FFR of welding wires in the "drop-spray" mode of transfer.
Rehabilitating Destructed Reinforced Concrete T Connections By Steel Straps, Muhammad N. S Hadi
Rehabilitating Destructed Reinforced Concrete T Connections By Steel Straps, Muhammad N. S Hadi
Faculty of Engineering - Papers (Archive)
The aim of this paper is to present results of testing a full scale reinforced concrete T connection by static loading. The connection represents a beam-column connection. The beam and column had a square cross section with a 300 mm dimension. The height of the column was 2.9 m and the clear beam length was 1.4 m. The connection was initially tested to failure. Galvanised steel straps were used to rehabilitate the connection. Epoxy resin was used to fix the steel straps to the concrete surface. The connection was tested after the rehabilitation. Results of testing the rehabilitated connection show …
Microstructure And Mechanical Properties After Annealing Of Equal-Channel Angular Pressed Interstitial-Free Steel, Sujoy S. Hazra, Elena V. Pereloma, Azdiar A. Gazder
Microstructure And Mechanical Properties After Annealing Of Equal-Channel Angular Pressed Interstitial-Free Steel, Sujoy S. Hazra, Elena V. Pereloma, Azdiar A. Gazder
Faculty of Engineering - Papers (Archive)
The evolution of microstructure, microtexture and mechanical properties during isothermal annealing of an ultrafine-grained interstitial-free steel after eight passes of route BC room temperature equal-channel angular pressing (ECAP) was studied. The microstructure and microtexture were characterized by electron back-scattering diffraction, and mechanical properties were assessed by shear punch and uniaxial tensile testing. Homogeneous coarsening via continuous recrystallization of the ECAP microstructure is accompanied by minor changes in the ∼63% high-angle boundary population and a sharpening of the original ECAP texture. This is followed by abnormal growth during the final stages of softening due to local growth advantages. Linear correlations …
The Development And Manufacture Of Ultra-Thin Cast Strip Steel Products With High Residual Element Levels Via The Castrip® Process, Daniel G. Edelman, Peter C. Campbell, Chris R. Killmore, Kristin R. Carpenter, Harold R. Kaul, James G. Williams, Walter N. Blejde
The Development And Manufacture Of Ultra-Thin Cast Strip Steel Products With High Residual Element Levels Via The Castrip® Process, Daniel G. Edelman, Peter C. Campbell, Chris R. Killmore, Kristin R. Carpenter, Harold R. Kaul, James G. Williams, Walter N. Blejde
Faculty of Engineering and Information Sciences - Papers: Part B
A range of Ultra-Thin Cast Strip (UCS) sheet steels with elevated residual levels was produced via the CASTRIP twin drum casting method at Nucor Steel, Indiana. This paper examines the influence of elevated levels of copper, chromium, nickel, and phosphorous on mechanical properties, surface quality, processing, and weldability of UCS sheet steel products produced by the CASTRIP process. Increased levels of copper and phosphorous were found to strengthen UCS sheet steel due to solid solution strengthening but chromium and nickel did not. At lower coiling temperatures and low hot reductions, where processing conditions promote microstructural strengthening, copper and chromium further …