Engineering Commons^™

Autonomous Navigation And Control Of Unmanned Aerial Systems In The National Airspace, Michael Hlas, Jeremy Straub, Eunjin Kim

Jeremy Straub

Pilotless aircraft known as Unmanned Aerial Vehicles (UAVs) have been used extensively for military and intelligence purposes. This includes situations where the mission area is too dangerous for a pilot to fly, the length of the mission is longer than a pilot could stay awake or aircraft are used as cruise missiles that crash into their target. With the decreasing cost and miniaturization of computers, it has become possible to build UAVs that are small and inexpensive making them accessible to businesses, law enforcement, hobbyists and the general public.

The Use Of Low-Cost ‘Balloonsats’ For Stem Education With 3d Printing, Jeremy Straub, Josh Berk, John Nordlie, Ronald Marsh

Jeremy Straub

A new technology, known as 3D printing, allows the rap-id fabrication of plastic structures of virtually any config-uration. These structures are light-weight, dura-ble and inexpensive. This paper considers the utility of utilizing 3D printing to create enclosures for ‘BalloonSats’ – small, low-cost spacecraft analog which can be utilized by students to understand space engi-neering, conduct near-space science (e.g., physics, bio-logical and other experiments) and touch the edge of space.

Update On The Progress Of The 1-U Open Cubesat Development, Jeremy Straub, Ronald Marsh

Jeremy Straub

The OpenOrbiter program [1] is developing a low-cost framework for the creation of space-craft [2] by researchers and educators world-wide [3]. In line with the objective of enabling future educational use by others, educational assessment [4, 5] has been a key focus. Sever-al areas were assessed: students were asked what types of benefits they sought from their participation [6], assessment of benefit attain-ment is ongoing. Work on the development of a designs (See Figures 2 and 8) that can be used to build a spacecraft with a cost of under $5,000 [7] using primarily COTS parts and testing (see Figure …

The Differences Are Not So Great: High Altitude Balloon And Small Spacecraft Software Development, Jeremy Straub, Ronald Marsh

Jeremy Straub

Previous work discussed critical differences in planning, developing hardware for and executing a high altitude balloon (HAB) mission. One area where this difference is less pronounced is in software development, allowing HABs to be utilized as a ‘software testbed’ for many orbital missions. This paper provides an overview of the software development process for both orbital and HAB craft, highlighting differences between the two processes and the numerous similarities. It concludes by presenting a framework for analyzing the suitability of HAB testing for small satellite software.

A Low-Cost Gps/Inertial Position Determination System For High Altitude Balloons, Spacecraft And Unmanned Aerial Systems, Tyler Leben, Jeremy Straub, Ronald Marsh

Jeremy Straub

A low-cost system is needed to determine precise position and predict future location in flight and low-Earth orbit. One method to accomplish this task is to utilize an onboard GPS receiver. GPS units receive data from the GPS NAVSTAR constellation of 24 satellites in the form of a 37 byte ASCII text sent at 4800 baud called NMEA sentences. The standard is 1 HZ, which is one sentence per second, but can be more. Ideally, from this data a PVT (position, velocity, time) and altitude can be determined. This data is then transferred from the GPS module to a separate …

The Path To Regulation Of Small Unmanned Aerial Vehicles In The United States, Jeremy Straub, Joe Vacek

Jeremy Straub

This poster presents an overview of proposed regulations that are presented in [1] related to a re-vised approach to small Unmanned Aerial Vehicles (UAV) regulation in the United States. Prospective strategies for enhancing UAV regulation are consid-ered as is the pathway to develop and implement these regulations. The benefits of changing the UAV regulatory regime are discussed, on both a user/prospective user and societal scale.

The Use Of Solar Balloons At Und As A Low-Cost Alternative To Helium Balloons For Small Spacecraft Testing And Stem Education, John Nordlie, Jeremy Straub, Chris Theisen, Ronald Marsh

Jeremy Straub

Helium-filled latex weather balloons have been utilized for many years to carry small satellite prototypes and subsystems into the stratosphere to allow testing in a “near space” (stratospheric) environment. A variety of environmental factors similar to the space environment can be found in this region, such as a rarified atmosphere, increased thermal stress including very low temperatures, increased solar radiation, the necessity of remote command and control, tracking, and telemetering of data. While this method of flight testing has been well-proven, a recent increase in the price of helium has driven the cost of such test programs to much higher …

The Use Of 3d Printing To Enable High Altitude Balloon Missions, Jeremy Straub

Jeremy Straub

The 3D printing technology allows the low-cost creation of structures based on user-defined configuration parameters. Unlike other plastic-forming technologies, there is no tooling cost related to the creation of a mold. Because of this, highly-customized structures can be created with a minimum production quantity of one, allowing adaptation to individual mission needs (for a single-HAB mission) or the change of the structure across a multi-unit run (e.g., to test various configurations or as part of a study requiring multiple payloads with different configurations).

This paper considers the mission possibilities enabled by the use of 3D printing for HAB structures. These …

Solar Ballooning: A Low-Cost Alternative To Helium Balloons For Small Spacecraft Testing, John Nordlie, Jeremy Straub, Chris Theisen, Ronald Marsh

Jeremy Straub

Helium-filled latex weather balloons have been utilized to carry small satellite prototypes and subsystems into the stratosphere to allow testing in a “near space” environment. This provides a variety of environmental factors similar to the space environment, such as a rarified atmosphere, increased thermal stress, increased solar radiation, the necessity of remote command and control, tracking, and telemetering of data. While this method of flight testing has been well-proven, a recent spike in the price of helium has driven the cost of such test programs to much higher levels. In this poster, an alternative technology to provide the flight mechanism, …

Enabling Interplanetary Small Spacecraft Science Missions With Model Based Data Analysis, Jeremy Straub

Jeremy Straub

Small spacecraft operating outside of Earth orbit are significantly constrained by the communica- tions link available to them. This is particularly true for stand-alone craft that must rely on their own antenna and transmission systems (for which gain and available power generation are limited by form factor); it is also applicable to ‘hitchhiker’-style missions which may be able to utilize (quite likely very limited amounts of) time on the primary spacecraft’s communications equip- ment for long-haul transmission.

This poster presents the adaptation of the Model-Based Transmission Reduction (MBTR) frame- work’s Model-Based Data Analysis (MBDA) component for use on an interplanetary …

Operating Standards For The High Altitude Ballooning Community, Jeremy Straub, John Nordlie, Ernest Anderson

Jeremy Straub

This paper provides an overview of work to define a set of standards for adoption by the academic high altitude balloon community. These standards go above-and-beyond the requirements imposed by §101 of the Federal Aviation Regulations, incorporating best practices and suggesting how §101 requirements should be interpreted and applied in several situations.

One area where FAR§101 is extremely vague is with regards to the operations of balloons with small payloads. These payloads are exempt from most requirements; however, they are required to not create a “hazard”. Problematically, what exactly qualifies as a “hazard” is not defined in FAR§101 or elsewhere …

Creating Low-Cost ‘Balloonsats’ For Stem Education With 3d Printing, Jeremy Straub

Jeremy Straub

A new technology, known as 3D printing, allows the rapid fabrication of plastic structures of virtually any configuration. These structures are light-weight, durable and inexpensive. This paper considers the utility of utilizing 3D printing to create enclosures for ‘BalloonSats’ – small, low-cost spacecraft analog which can be utilized by students to understand space engineering, conduct near-space science (e.g., physics, biological and other experiments) and touch the edge of space.

The utility of 3D printed structures for use in the near-space low-temperature and low-pressure environment is considered. This analysis falls into four key areas. First, the ability of the structures to …

Desktop Warfare: Robotic Collaboration For Persistent Surveillance, Situational Awareness And Combat Operations, Jeremy Straub

Jeremy Straub

Robotic sensing and weapons platforms can be controlled from a desktop workstation on the other side of the planet from where combat is occurring. This minimizes the potential for injury to soldiers and increases operational productivity. Significant work has been undertaken and is ongoing related to the autonomous control of battlefield sensing and warfighting systems. While many aspects of these operations can be performed autonomously, in some cases it is necessary (due to technical limitations) or desirable (due to legal or political implications) to involve humans in the low-level decision making. This paper reviews a number of specific applications where …

A Human Proximity Operations System Test Case Validation Approach, Justin Huber, Jeremy Straub

Jeremy Straub

A Human Proximity Operations System (HPOS) poses numerous risks in a real world environment. These risks range from mundane tasks such as avoiding walls and fixed obstacles to the critical need to keep people and processes safe in the context of the HPOS’s situation-specific decision making. Validating the performance of an HPOS, which must operate in a real-world environment, is an ill posed problem due to the complexity that is introduced by erratic (non-computer) actors. In order to prove the HPOS’s usefulness, test cases must be generated to simulate possible actions of these actors, so the HPOS can be shown …

The North Dakota Space Robotics Program: Teaching Spacecraft Development Skills To Students Statewide With High Altitude Ballooning, Jeremy Straub, Ronald Fevig

Jeremy Straub

The University of North Dakota is serving as the lead institution in a statewide effort to develop student spacecraft engineering skills. This effort, which is part of the North Dakota Space Robotics Program (NDSRP), provides students the ability to participate in the design, development and fabrication of a small satellite analog that is launched by a high altitude balloon. The first iteration of the NDSRP Near-Spacecraft Project is generating a functional prototype of a remote sensing payload, which will perform onboard image processing. This project included undergraduate and graduate students from two institutions and five different academic departments. The students …

Formalizing Mission Analysis And Design Techniques For High Altitude Ballooning, Jeremy Straub, Ronald Fevig

Jeremy Straub

High altitude balloon (HAB) missions can be and are used to teach concepts related to spacecraft and satellite design. A HAB mission, however, presents unique characteristics, which must be understood and respected to produce a desirable outcome. Because of this, flying an unaltered satellite design as a HAB payload would be as undesirable as utilizing an unaltered HAB design as a satellite. A well-defined process for HAB mission design is thus needed. The process presented mirrors commonly used space mission design processes to facilitate easy transition between the two. It is also comparatively simple, due to the smaller scale of …