Engineering Commons^™

Anti-Freeze Double Network Hydrogels, William Gross

Williams Honors College, Honors Research Projects

Three polyethylene glycol (PEG) based crosslinkers with repeat unit nominal weights of 62.1, 200, and 400 g/mol in agar/PAM double network (DN) hydrogels were used to study the effect of different crosslinkers on thermal and mechanical properties. Using the one-pot synthesis method, hydrogels with the PEG crosslinkers or methylene-bis-acrylamide (MBAA) were made via sol-gel transition for formation of agar network, and photopolymerization of the PAM network using Irgacure 2959 as photo initiator. Tensile and compression tests were performed on as prepared, swollen, and swollen & cooled specimens of each hydrogel. Freezing time and thermal imaging were performed in -20 °C …

Structural Design And Application Of Polymeric Silicon Elastomers, Jacob Wyant

Williams Honors College, Honors Research Projects

The purpose of this project was to determine how the polymeric structure and mechanical properties of this elastomer are affected by the ratio between the polydimethylsiloxane macromolecular chains and the crosslinkers. These were determined via tensile and compression testing. Then, spiropyran was added to observe how this fluorescence and crosslinking agent affected the elastomer. Also, the elastomer’s fluorescent and icephobic nature were tested. The elastomers with a higher ratio of crosslinker to macromolecular chain could withstand higher tensile and compressive strains but failed at lower stresses than their counterparts with lower concentrations of crosslinkers. The elastomers were also found to …

Running Shoe Pedometer, Benjamin Kasper

Williams Honors College, Honors Research Projects

Running shoe pedometer aims to solve the issue of worn out running shoes. It can be difficult to know just how many miles you have run in your shoes and when a new pair is needed. Running in old shoes and worn out shoes is heavily linked to injury. My proposed project is a device that is powered by the compressive forces on the shoes soles that counts the number of steps the wearer takes using a microcontroller. Then, when the shoe reaches milestone that indicate it has been used 75% 90% and 100% of its expected life, it will …

Defining The Proper Operating Time For The Septa Extractor, Abigail Jones

Williams Honors College, Honors Research Projects

Anionic polymerizations are a common type of reaction used to produce synthetic rubber. During these reactions, it is necessary to charge initiators, modifiers, and other substances, through pressurized containers that are sealed with rubber septa. These septa prevent oxygen and moisture from entering the pressurized container, and the reactor, though they need to be cleaned before use to remove other impurities. Currently a glass Soxhlet Extractor is used to remove such impurities, and though effective, it has a limited capacity, so it has to run frequently. This limitation led to the commissioning of the Septa Extractor, which is an automated …

Utilizing Computer-Aided Molecular Design With Azido-Ester Plasticizers, Justin Ebert

Williams Honors College, Honors Research Projects

The goal of this project was to utilize Computer-Aided Molecular Design (CAMD) using the Signature molecular descriptor to inversely design optimized azido-ester plasticizers. Azido-ester plasticizers are used to modify the mechanical properties of propellant and explosive formulations. With the assistance of quantitative structure-property relationships, QSPRs, and two types of constraint equations, these new, novel plasticizers have the potential to possess optimal physical and chemical properties. Properties investigated in this work were decomposition temperature, heat of formation, glass transition temperature, and molecular weight. These properties were chosen for their importance when formulating propellants or explosives. After the filters were applied to …

Beeswax Wraps As An Alternative To Single-Use Plastics, Sarah Skiver

Williams Honors College, Honors Research Projects

The project goal was to compare the food storage efficacy of sustainable beeswax wraps verses the single-use plastic methods of resealable plastic sandwich bags and plastic cling wrap. The goal was also to test the reusability of the beeswax wraps, as it is a key advantage of beeswax wraps that is advertised. The project purpose was to explore sustainable and eco-friendly alternatives to single use plastics, which are harmful to the environment in both their production and their disposal. Food spoilage was compared in beeswax wrap, plastic sandwich bags, and plastic cling wrap, and spoilage was also observed in a …

Comparing Weathering Effects Of Ultraviolet And Xenon Arc Accelerated Aging On Polyvinyl Chloride, Collin Mcinnes

Williams Honors College, Honors Research Projects

As the ubiquitousness of polymers increases and begins seeing use in outdoor settings, the need to fully understand how these materials degrade is also necessary. This study aims to compare two known accelerated aging methods, namely an ultraviolet light chamber and a xenon arc light chamber, to understand what differences, if any, manifest in the mechanical, chemical, and cosmetic deterioration of polyvinyl chloride (PVC) after long-term exposure. The study utilizes Fourier-transform infrared spectroscopy, dynamic mechanical analysis, thermogravimetric analysis, and colorimetry analysis to determine the extent of degradation and potential discrepancies between the aging methods.

Design Project: 3d Printer/Injection Molder Hybrid, Lee Paolucci, Luke Everhart, Brandon Leap, Karson Lorey

Williams Honors College, Honors Research Projects

In the realm of rapid, small-scale prototyping, there are a few main factors that drive decisions to invest resources in technology to make that prototyping possible. Cost and ease of use are two of the most influential when looking at most SMEs (Small to Medium-sized Enterprises). The U.S. Small Business Administration defines an SME as smaller than 1,250 employees. According to An Assessment of Implementation of Entry-Level 3D Printers from the Perspective of Small Businesses, 59% of small manufacturers had implemented 3D printers as of 2014. However, no matter what technology is used in rapid prototyping, there are common …

Retaining Thermoresponsive Poly(Vinyl Methyl Ether) To Cellulose Via (3-Aminopropyl)Triethoxylsilane Network, Grace Tolhurst

Williams Honors College, Honors Research Projects

Stimuli-responsive supports and devices that are fabricated from inexpensive materials are attractive candidates for a variety of applications, such as environmental protection, and regenerative medicine. Poly(vinyl methyl ether) (PVME), a thermoresponsive polymer (TRP), has recently been used as thermoresponsive cell culture supports for cell growth/proliferation followed with cell/cell sheet harvesting by simply switching temperature. Cellulose is an attractive candidate to replace glass/silicone supports as it is inexpensive and environmentally friendly. This project focuses on retaining PVME to the cellulose membrane via 3-aminopropyltriethoxysilane (APTES) network to generate TR membranes and flexible liners that can be incorporated into bioreactors for producing cells …

Recycled Printer Filament, Charlotte Hyland, Troy D. Molinar

Williams Honors College, Honors Research Projects

The purpose of this research is to examine the effects of recycling PLA filament for 3D printing on its material properties. After examining these effects, PLA and carbon fiber additives were mixed with recycled PLA pellets in different ratios to attempt to regain material properties lost in the recycling process. To complete these findings, an experiment was design and executed.

The research found that tensile strength during multiple iterations of recycling remained mostly unaffected, however, the strain degraded exponentially. In the PLA additive study, high ratios of PLA additive were able to increase the strength and strain properties of the …

Wetting Transition On 3d-Printed Surfaces, Isabelle Moryan

Williams Honors College, Honors Research Projects

Taking the previous research conducted, this project aims to further the study and research of the wettability of surfaces. Surface features and types are important factors to their wettability. The geometric properties of a surface can make it more hydrophobic and hydrophilic. Extreme cases of hydrophobic and hydrophilic surfaces lead to water repulsion or water absorption, even under extreme conditions. The goal of this project is to gain further insight on how fabricated 3D-printed featured surfaces and examine the wetting transition on these surfaces. In particular, cylindrical pillars will be studied with varied pillar spacing, height and diameter. In addition, …

Reinforcement Of Elastomers By Reactive Ionic Surfactant, Nicole Vickerman

Williams Honors College, Honors Research Projects

Elastomers without cross-linking agents or fillers do not have the necessary properties for practical applications in the rubber industry. Elastomers must be reinforced with fillers and/or cross-linking agents to achieve the needs of physical and mechanical properties for commercial products. Sodium octyl 6-mercaptohexyl phosphate (SOMP) and sodium ethyl (6-mercaptohexyl) phosphate (SEMP) were used to investigate the influence of a reactive ionic surfactant and its influence on the physical properties of peroxide crosslinked styrene butadiene rubber (SBR). SEMP and SOMP were both found to be able to be grafted successfully on to the SBR chains within the rubber using extraction testing …

Application Of Sla 3d Printing For Polymers, Taylor Wilson

Williams Honors College, Honors Research Projects

Stereolithography is a type of 3D printing that allows liquid photopolymer resin to be cured into layers that make up a 3D object. Creation of such resins for these purposes can require a significant amount of time to test and develop, and commercial resins also require some amount of testing for printer settings before use. This paper reviews how stereolithography works, the materials used, and experimentation done to compare the resin properties to the determined curing times. Using several commercially available resins, varying base exposure and layer exposure times were used to determine the lowest possible curing time that gave …

Mimicking The Namib Desert Beetle With Hydrophilic And Hydrophobic Surfaces, Tyler Bracewell

Williams Honors College, Honors Research Projects

The Namib Desert beetle, Stenocara gracilipes, condenses fog that rolls in off the west coast of Namibia to provide itself with the water it needs for the day. By lifting its abdomen into the air to collect the water vapor, it condenses on hydrophilic bumps that are about 500μm in diameter and are spaced apart about 500-1500μm. Once the water reaches a critical size, the droplet rolls off the hydrophilic bump and onto the flat hydrophobic surface of the elytra. Since the beetle is angled with its abdomen in the air, the water rolls down to its mouth. A …

Amine-Functionalized Interpenetrating Polymer Networks For Co2 Capture, James Wills

Williams Honors College, Honors Research Projects

The research performed looked to advance the studies of vacuum swing absorption of Carbon Dioxide to help combat global climate change issues. The focus of the project was to create an anime-polymer sorbent that will weakly absorb and desorb CO2. The sorbent must be durable and be able to withstand multiple uses. The creation of a porous polymer matrix aided in the amines' ability to absorb CO2. Created samples underwent several qualitative and quantitative tests to determine their usefulness as an industrial sorbent. Infrared spectroscopy was used to study the effectiveness of the amine sorbents. Studying the changes in the …

Retention And Stability Of Polystyrene Sulfonic Acid And Polyethylene Glycol Anti- Fouling Films With 3-Aminopropyltriethoxysilane Coupling Agent, Brian Cameron

Williams Honors College, Honors Research Projects

Fouling is a process where particles, proteins, or microorganisms will accumulate onto a material [2]. This can lead to biofilms in medical implants, which can trap and create drug resistant bacteria [5]. Due to this, the study and creation of anti-fouling polymeric films that is stable in aqueous environments is essential. The goal of this study is to utilize APTES to retain the already studied PSS-PEG anti-fouling films. The films that are created is a thermally crosslinked network of the polystyrene sulfonic acid (PSS) and polyethylene glycol (PEG) with differing mass fractions (75- 25 and 55-45 PSS-PEG). To retain the …

Amino-Polymer For Co2 Capture By Vacuum Swing Adsorption, Sean Billy

Williams Honors College, Honors Research Projects

The applications of sorbent compounds in conjunction with amines and other additives is an innovative method at combating CO2 pollution. An ideal solution would use an amine sorbent to trap the high levels of absorbed CO2 with a low binding energy (less than 45 kJ/mol) and subsequently release them into a stored vessel at ambient temperature with a vacuum swing adsorption system. Attempts at finding a best mixture will be conducted through the usage of a vacuum swing system, utilizing a bed syringe containing the sorbent mix and a vacuum syringe to pull on and subsequently release the CO2 into …

Development Of Co2 Capture Method Via Polyurethane-Amine Sorbent In Vsa, Samantha Starkey, David S. Rinehart

Williams Honors College, Honors Research Projects

With increases in extreme weather and global temperatures, research is delving into CO₂ capture to help reverse climate change. This project explored utilizing vacuum swing adsorption (VSA) for CO₂ capture and release. VSA uses a sorbent, in this case amine sorbents, to capture CO­­₂ from air and subsequently removes it via vacuum. Polyurethane (PU) foam was investigated as a potential matrix for amine sorbents to increase exposure of CO₂ capturing amines to air by utilizing its porous structure. PU mixing studies were conducted to determine the feasibility of mixing PU foam with amines and coating foams …

Comparison Of The Effects Of Hofmeister Ions On Transition Temperature Of Two Thermoresponsive Polymers, Ashley Knight

Williams Honors College, Honors Research Projects

It has been hypothesized that poly(vinylmethylether) (PVME) could be used to replace poly(N-isopropylacrylamide) (pNIPAAM) in various thermoresponsive applications based on literature searches and previous lab experiments. PVME is cheaper and easier to process, and would make pNIPAAM applications more cost effective. In order to verify this, experimental data was gathered on the effects of four anions from the Hofmeister series (SO₄₂-, Cl-, I-, and SCN-) on the lower critical solution temperature (LCST) of pNIPAAM and compared to previous data collected on PVME. Commercial pNIPAAM from Sigma Aldrich and Polysciences were used. The reported LCST range for pNIPAAM is …

Investigation Of Surface Charge Using Faraday Bucket Measurements: Analysis On Electrospun Polyvinylidene Fluoride Fiber Mats, Ryan Kantenwein

Williams Honors College, Honors Research Projects

Piezoelectric polymer materials such as polyvinylidene fluoride exhibit beneficial properties for use in personal protective equipment (PPE) against viral contaminants and other foreign microparticles. The electrospinning process of this material allows for surface charge to develop over a controlled surface area. Kynar 761 at 10 wt% demonstrates increased surface charge after withstanding a flow of aerated NaCl particles from a TSI 8130 instrument. Utilizing voltage measurements from a Faraday bucket, 18 wt% Kynar 761 and MG-15 exhibit surface charge when undergoing an electrospinning process; however, Kynar MG-15 displays lower charge values than that of Kynar 761. Several critical factors such …

Wetting Transition On 3d-Printed Featured Surface, Hannah Pineault

Williams Honors College, Honors Research Projects

The primary objective of this research project was to gain a better understanding of surface characteristics to produce a long-lasting superhydrophobic or superhydrophilic surface. In other words, when will a droplet of water remain on top of a featured surface and when does the transition occur to water filling the grooves of the surface? This research focused on how to best fabricate porous structures that would stay completely dry at all times by preventing the liquid from penetrating. In particular, we followed the behaviors of water droplets placed on top of 3-D printed featured surfaces with various geometries and surface …

Molecular Recognition Of Pet Depolymerization Products And Beta-Cyclodextrin, Thomas Palisin

Williams Honors College, Honors Research Projects

Using molecular recognition techniques to determine the binding constant of the host-guest relationships of the depolymerization products of polyethylene terephthalate (PET) and cyclodextrin species. The main method of data collection used was florescence spectroscopy. Using a titration method and measuring the florescence intensity, a nonlinear regression was used to determine the binding constant.

Evaluating The Thermoresponsive Properties Of Hydroxypropyl Cellulose Solutions For Smart Window Applications, Adam Reed

Williams Honors College, Honors Research Projects

With HVAC and building energy usage expected to increase, there is a strong need for autonomous thermal management solutions. In particular, there has been a growing interest in thermoresponsive (TR) smart windows that are activated by ambient temperature changes. Most TR smart windows contain a liquid solution between two panes. The goal of this research project was to develop a self-supporting smart window by forming a gel that maintained its TR properties. A gel is less prone to spilling in the case of window breakage. It was also desired to tune the phase transition to occur at environmentally relevant conditions …

Quantifying Mafenide Release From 3d Printed Phenylalanine-Coumarin Copolyester Scaffolds, Jacob Seeh

Williams Honors College, Honors Research Projects

This project addressed burn wound healing through controlled release of the antibacterial drug mafenide encapsulated by a copolyster into 3D printed scaffolds. Scaffolds were printed at 25^oC and 0.77-1 bar in a cross-hatch pattern with uniform thickness, distance between parallel layers, and diameter then photo-crosslinked. The number of scaffolds available for testing was limited by the amount of polymer that could be synthesized. A high-performance liquid chromatography method was developed specifically for this experiment and used to determine daily release of mafenide from the scaffold into a 2-mL phosphate buffer solution. During the first 24 hours a large …

Zips Precious Plastics: Plastic Extruder, Patrick Cole

Williams Honors College, Honors Research Projects

This project's goal was to design and build an affordable desktop filament extruder that can precisely and consistently extrude filament to a certain tolerance acceptable for 3D printers using wasted printing material. The group is partnering with an on campus organization focusing on engineering applications for sustainable futures. Zips Precious Plastics is a student run design group that intends to bring an innovation space on campus to help educate students about the importance of a closed looped system within plastic manufacturing.

Exploring Shape-Memory Polymers From Silicone I And 1,10-Decanediol Blends, Kristina Nguyen

Williams Honors College, Honors Research Projects

Shape-memory polymers (SMPs) are polymeric materials that have dual-shape capabilities. These materials can deform to a temporary shape and will recover to their permanent original shape when induced by an external stimulus such as heat. The purpose of this project was to investigate the thermo-mechanical properties and shape-memory behavior of various blends of Silicone I and 1,10-decanediol to determine if a unique blend of these components can be utilized to develop shape memory surface relief patterns.

Careful iterative experiments were used to develop a robust procedure for the fabrication of crosslinked sheets of blends of Silicone I and 1,10-decanediol over …

Methods For Film Coating Electrospun Fibers, Kristopher Dejean

Williams Honors College, Honors Research Projects

Electrospinning uses high voltages to form polymer nanofiber membranes. These membranes have potential for use in filtration, tissue engineering, drug delivery, and catalysis. The nonwoven fiber mat is malleable but has a low tensile strength compared to a solid film of the same polymer. Joining the fibers with a thin film is desired to balance the strength and flexibility. Three methods of producing a film on fiber membrane were tested. The techniques are spraying then melting, spin coating, and dip coating. Electrospinning setup conditions, solvent ratios, damage to fibers, and spin coating speeds were determined. Research was abruptly stopped and …

Evaluating Rubber Aging On Tire Durability: Quantitative Evaluation Of Rubber Aging, Brian Auffenberg

Williams Honors College, Honors Research Projects

Rubber is considered one of the most important polymers in the world due to its variety of uses. There are many different conditions that can affect the useful life of rubber. The purpose of this research was to determine how the mechanical loading on the rubber may affect the aging of the rubber. The scope of the project was to focus on the rubber used for tire production. The research was limited to focusing only on rubber supplied by industry mentors which was styrene-butadiene rubber. By varying the length of time for testing as well as the temperature of the …

Design Of Pigments For Use In “Cool” Coatings, Tyler Laughorn

Williams Honors College, Honors Research Projects

This project was focused on the development and testing of several novel pigments that exhibit high NIR-reflectance and therefore show potential for use in “cool” coatings. A “cool” coating will reflect more solar radiation than other standard coatings, and so a coated structure would require less energy to keep cool. Four sets of pigments were synthesized: Co_1-xMg_xCr₂O₄ (teal), Co_0.25Mg_0.75Cr_2-yAl_yO₄ (blue), Ti_1-x-yNi_xSb_yO₂ (yellow), and Cr_2-xFe_xO₃ (black). NIR and TSR values were then measured …

A Comparison Of Fiber Mat Thickness Measurement Techniques Using Laser Interferometry And Water Displacement, Ryan Seabeck

Williams Honors College, Honors Research Projects

Polymer fiber mats may often be very thin which leads to complications in measuring thickness. The thickness of fiber mats, however, is crucial in understanding their behavior. Thickness affects how well the mat works as a filter as well as the pressure drop across the mat, and herein lies the need for accurate measurement techniques. Currently two of the available techniques for measuring mat thickness are by laser interferometry[1] and by buoyancy force when submerged in water[2]. Instead of measuring the buoyancy force in this experiment, an enclosure intended to measure the thickness via water displacement was …