Engineering Commons^™

Micro Electrostatic Actuation Of A Silicon Diaphragm, Matthew W. Samples

Master's Theses

There are a number of applications, from hearing aids to microfluidic pumps, which utilize micro-scale actuating diaphragms. These MEMS (micro-electromechanical system) devices can be actuated by electrostatic forces, which utilize an induced electric field to pull two charged plates towards one another. Such devices were fabricated and electrostatic actuation of the diaphragms was performed to analyze its viability as a micro-speaker. The long-term performance of such products requires adequate diaphragm deflection to create audible pressure waves with relatively low maximum stresses to ensure a high cycle fatigue life. With these requirements, initial calculations and FEA (finite element analysis) were performed …

Design, Implementation, And Test Of A Micro Force Displacement System, Evan Derek Cate

Master's Theses

The design and implementation of a micro-force displacement system was completed to test the force-displacement characteristics of square silicon diaphragms with side lengths of 4mm, 5mm, and 7mm with a thickness of 10um. The system utilizes a World Precision Instruments Fort 10g force transducer attached to a World Precession Instruments TBM4M amplifier. A Keithley 2400 source meter provided data acquisition of the force component of the system. A micro prober tip was utilized as the testing probe attached to the force transducer with a tip radius of 5um. The displacement of samples was measured using a Newport M433 linear stage …

Design And Fabrication Of Electrostatically Actuated Serpentine-Hinged Nickel-Phosphorous Micromirror Devices, Nicholas A. Wiswell

Master's Theses

A process for micromachining of micro-mirror devices from silicon-on-insulator wafers was proposed and implemented. Test methods and force applicators for these devices were developed. Following successful fabrication of these devices, a novel process for fabrication of devices out of the plane of the silicon wafer was proposed, so that the devices could be actuated electrostatically. In particular, the process makes use of thick photoresist layers as a sacrificial mold into which an amorphous nickel-phosphorous alloy may be deposited. Ideal design of the electrostatically actuated micro-mirrors was investigated, and a final design was selected and modeled using FEA software, which found …

Fabrication And Characterization Of Torsional Micro-Hinge Structures, Mike Madrid Marrujo

Master's Theses

ABSTRACT

Fabrication and Characterization of Torsional Micro-Hinge Structures

Mike Marrujo

There are many electronic devices that operate on the micrometer-scale such as Digital Micro-Mirror Devices (DMD). Micro actuators are a common type of DMD that employ a diaphragm supported by torsional hinges, which deform during actuation and are critical for the devices to have high stability and reliability. The stress developed within the hinge during actuation controls how the actuator will respond to the actuating force. Electrostatically driven micro actuators observe to have a fully recoverable non-linear viscoelastic response. The device consists of a micro-hinge which is suspended by two …

Design, Fabrication, And Characterization Of A Thin-Film Nickel-Titanium Shape Memory Alloy Diaphragm For Use In Micro-Electro-Mechanical Systems, Brian Joel Alvarez

Master's Theses

Previous work done at Cal Poly has shown that thin-film nickel-titanium (NiTi) can be easily sputtered onto silicon wafers and annealed to create a crystallized shape memory alloy (SMA) film. Initial work on creating devices yielded cantilevers that were highly warped due to thin-film stress created during the sputtering process. The objective of this work was to create a thin-film NiTi SMA device that could be better characterized. A membrane was selected due to the simplicity of fabrication and testing which would also oppose the thin-film stress due to the increase in attachment points to the substrate.

Silicon wafers were …

Characterization Of A Viscoelastic Response From Thin Metal Films Deposited On Silicon For Microsystem Applications, Steven L. Meredith

Master's Theses

Understanding the mechanisms that control the mechanical behavior of microscale actuators is necessary to design an actuator that responds to an applied actuation force with the desired behavior. Micro actuators which employ a diaphragm supported by torsional hinges which deform during actuation are used in many applications where device stability and reliability are critical. The material response to the stress developed within the hinge during actuation controls how the actuator will respond to the actuating force. A fully recoverable non-linear viscoelastic response has been observed in electrostatically driven micro actuators employing torsional hinges of silicon covered with thin metal films. …

Design, Fabrication, Modeling And Characterization Of Electrostatically-Actuated Silicon Membranes, Brian C. Stahl

Master's Theses

This thesis covers the design, fabrication, modeling and characterization of electrostatically actuated silicon membranes, with applications to microelectromechanical systems (MEMS). A microfabrication process was designed to realize thin membranes etched into a silicon wafer using a wet anisotropic etching process. These flexible membranes were bonded to a rigid counterelectrode using a photo-patterned gap layer. The membranes were actuated electrostatically by applying a voltage bias across the electrode gap formed by the membrane and the counterelectrode, causing the membrane to deflect towards the counterelectrode. This deflection was characterized for a range of actuating voltages and these results were compared to the …