Growth, Characterization, And Mechanical Testing Of Diamond-Like Carbon Films, Tailei Qi

LSU Master's Theses

The high residual stresses within diamond-like carbon (DLC) films limit its thickness and make the film tend to delaminate from the substrate and be defective on the surface. To address this problem, a new plasma enhanced chemical vapor deposition system (PECVD) was set up to investigate the effects of different film growth parameters on the DLC films, such as chromium doping, gas fluxes, depositing pressures, bias voltages, and depositing times. After the film growth parameters were optimized, this condition was transferred from silicon wafer to SS316 steel plate to deposition of DLC films with some adjustments. Scanning electron microscopy (SEM) …

Cfd Simulations Of Macroscopic And Microscopic Multiphase Fluid Flow And Droplet Interaction, Aaron Harrington

LSU Master's Theses

Multiphase flow is a complex phenomenon which can be modeled on numerous different length scales, both macroscopically and microscopically. The use of a Euler-Euler model for Computation Fluid Dynamics (CFD) simulations of subcooled boiling phenomena is discussed in detail. The CFD conditions have been set up to mimic previous experimental conditions. A cylindrical vessel with subcooled liquid flow is heated along part of the axial wall of the vessel. A constant heat flux is applied to produce subcooled boiling. We discuss the development of the phase change within the vessel as well as the temperature profile, and validate the results …

Investigation Of Sand-Biochar Mixtures As A Potential Roadway Fill Material, Katia J. Lele Lagmago

LSU Master's Theses

Biochar is a sustainable and lightweight carbon-rich material with a high surface area and porosity. Previous studies reported that biochar can reduce soil erosion and cracking, retain contaminants, and enhance soil aggregation. Given these favorable properties, soil-biochar mixtures have the possibility to serve as a multifunctional lightweight fill material for roadway embankment applications. The purpose of this research is to develop sand-biochar mixtures as a sustainable and multifunctional lightweight fill material for roadway embankment applications.

This research investigated the consolidation and hydraulic properties of sand-biochar mixtures by (1) performing 1D consolidation tests, (2) performing permeability tests, and (3) assessing the …

A Modular Open-Technology Device To Measure And Adjust Concentration Of Sperm Samples For Cryopreservation, Nikolas C. Zuchowicz

LSU Master's Theses

Repositories for aquatic germplasm can safeguard the genetic diversity of species of interest to aquaculture, research, and conservation. The development of such repositories is impeded by a lack of standardization both within laboratories and across the research community. Protocols for cryopreservation are often developed ad hoc and without close attention to variables, such as sperm concentration, that strongly affect the success and consistency of cryopreservation. The wide dissemination and use of specialized tools and devices can improve processing reliability, provide data logging, produce custom hardware to address unique problems, and save costs, time, and labor. The goal of the present …

A Conceptual Framework For Phase-Dependent, Composite Flood Risk Index (Fri) Curves Based On The Relationship Between Temporal Probability Of Flood Occurring (Ph) And Flood Vulnerability Index (Fvi) Along With Maps Of Fvi Within The Amite River Basin Based On The August 2016 Flood., Austin S. Guerin Mr.

LSU Master's Theses

Efforts directed at determining community vulnerability to flooding are limited and only include economic (dollar damages) and public safety impacts and do not consider the phase dependency of the system, i.e., pre-, during- and post-storm, both critical shortcomings for more broadly assessing community risk and developing comprehensive plans and mitigation strategies. This thesis first develops a framework based on a Flood-Vulnerability Index (FVI) approach and then demonstrates its usefulness, at the census tract level of detail, for three parishes in the Greater Baton Rouge, LA area, based on the August 2016 flood. FVI’s indicators are multidimensional and phase dependent: “Pre-Flood” …

Degumming Of Hemp Fibers Using Combined Microwave Energy And Deep Eutectic Solvent, Bulbul Ahmed

LSU Master's Theses

Hemp is considered as one of the sustainable agricultural fiber materials. Degumming or surface modification of hemp bast is needed to produce single fibers for ensuing textile and industrial applications. The traditional degumming process necessitates a high amount of alkali, which causes detrimental environmental pollution. This study offers a new method to degum hemp fibers with reduced use of harmful alkali and precious water resources. In this work, hemp bast fibers were degummed by using combined microwave energy and deep eutectic solvent (DES). The properties of hemp fibers manufactured by this method were investigated and compared with the traditional alkali …

Evaluation Of Cell Concentration And Viability By Impedance Spectroscopy On Microfluidic Devices, Jason Eades

LSU Master's Theses

This document describes two distinct platforms that implement electrochemical impedance spectroscopy (EIS) within microfluidic devices for rapid, label-free cell analysis. Each study provides proof-of-concept evaluations of these devices for cell counting and viability analysis applications to mitigate some of the challenges associated with conventional methods. Chapter one includes background information on each version of EIS selected and motivations for the studies conducted. Chapter two describes the design and fabrication of a modular, reusable microfluidic device. Additionally, the methodology for and results from the application of this platform for the measurement of zebrafish sperm cell concentrations are presented. Chapter three describes …

Gas Evolution Phenomenon Of Methane In Base Fluids Of Non-Aqueous Drilling Muds Under Controlled Depressurization, Damilola Ojedeji

LSU Master's Theses

As wells become more complex and drilling conditions to reach targets prove even more challenging, being able to detect influx event early and safely handle these influxes has become one of the most important focus areas for improvement in well control safety. The high solubility of formation gas in non-aqueous drilling fluids however makes kick detection and safe handling of kicks more complicated. Recent studies are beginning to incorporate desorption kinetics in well control models to simulate the transient multiphase flow phenomenon associated with gas kicks in non-aqueous drilling fluids to foster safe handling of kicks. However, there is currently …

A Study Of Methane-Liquid Absorption Characteristics For Gas Influx Management, Scott A. Perry

LSU Master's Theses

The study of absorption mass transfer kinetics in non-aqueous base fluids and the investigation of the parameters that influence this process is crucial in the application to gas influx management. While there have been a large number of studies investigating the interaction and solubility of methane in non-aqueous drilling fluids, relatively little attention has been placed on studying the mass transfer kinetics for different scenarios within the wellbore and riser. During the drilling process, there are multiple ways in which the formation gas can come into contact with the drilling fluid via a gas kick. Once the gas influx dissolves …

Evaluating Word Embedding Models For Traceability, Mahfuza Khatun, Mahfuza Khatun

LSU Master's Theses

ABSTRACT

Traceability link recovery (TLR) is a software engineering activity that helps to ensure software quality and assists with keeping track of changes by establishing links between software artifacts that are a part of the software engineering process, such as requirements, use cases, source code, test cases, and documentation. Software requirement artifacts are typically written in natural language. An Information Retrieval process is frequently used in many software activities, including the TLR activity. Recently, Word Embedding (WE) techniques have been used in many natural language processing tasks as well as in TLR tasks. We investigate the effectiveness of WE techniques …

Finite Element Numerical Modeling And Parametric Study Of Geosynthetic Reinforced Pile-Supported Embankments, Abdallah Ikbarieh

LSU Master's Theses

This study directed at investigating the performance of the pile-supported embankment system utilizing a geosynthetic reinforced load transfer platform (GRLTP) using Finite Element numerical modeling. A 2D Finite Element Modeling (FEM) methodology was first developed using PLAXIS 2D 2021 computer software and verified by well-documented case studies in the literature of this system. Second, a performance prediction was made for a field case study of the Amite River Project near French Settlement, which is located along Route LA 16 Livingston Parish in Louisiana State. A comprehensive FEM parametric study was then carried out to evaluate the performance of the system …

Assessment Of Long-Term Performance Of Pavements Containing Warm Mix Asphalt Technologies In Louisiana, Kwadwo Ampadu Boateng

LSU Master's Theses

This study focused on the assessment of long-term performance of asphalt pavements containing warm mix asphalt technologies in Louisiana. A total of five rehabilitation projects were studied in the state of Louisiana. The study consisted of engineering desk analyses of field performance indicators, indices and the initial laboratory performance indicators measured for five rehabilitation projects.

The engineering desk study consisted of a review of literature from previous WMA technology projects done in Louisiana. Additionally, data was acquired and validated from the Louisiana Pavement Management System (PMS). Pavement performance indicators (i.e., cracking (transverse, longitudinal, and fatigue cracking), roughness, rutting, and pavement …

Lyapunov Function-Based Stabilizing Control Scheme For Wireless Power Transfer Systems With Lcc Compensation Network, Abu Shahir Md Khalid Hasan

LSU Master's Theses

A stabilizing control scheme based on a Lyapunov function is proposed for wireless power transfer (or WPT) systems. A state-space model of the WPT system is developed and the Lyapunov function is formulated based on an energy equation of the system involving state variables. The internal resistance of a battery varies during charge and discharge. Therefore, if a WPT system is used to charge a battery, its output load will vary. Furthermore, the coupling coefficient between the transmitter (primary) and receiver (secondary) coils decreases when they are misaligned. Comparative case studies are conducted to verify the efficacy of the proposed …

Enhanced Oil Recovery In Tight Rocks Using The “Slot-Drill” Completion, Hassan Amer

LSU Master's Theses

Enhanced oil recovery (EOR) is essential in shale/tight formations because primary recovery typically produces less than 10% of the original hydrocarbon in-place (OHIP). This work presents a novel “slot-drill” EOR technology, which involves injecting gas through a horizontal fracture that is cut into the formation near the top of the reservoir (using a tensioned abrasive cutting cable mounted to the drillstring) and producing oil from a second slot-drilled horizontal fracture near the bottom of the reservoir.

The dusty-gas diffusion model was implemented in a compositional simulator to account for the diffusion mechanism expected during the injection of gases in this …

Performance Evaluation Of Gas Lift Valves Using Numerical Simulation, Felipe Simoes Maciel

LSU Master's Theses

This work aimed to assess the performance of two numerical simulation methods to replicate flow capacity test (FCT) results and predict the flow coefficient (Cv) and critical pressure ratio (Rcp) of gas lift valves (GLVs). FCT's use a modified GLV with an adjustable stem positioning system to obtain pressure as a function of flow rate for different stem positions to calculate Cv and Rcp. Therefore, this study used both a one-dimensional (1D) mechanistic model and computational fluid dynamics (CFD) to predict the same variable from the FCT without tests using modified GLVs. This methodology demonstrates accurate results, which were compared …

Evaluating Hazus-Mh Flood Model Consequence Assessments Of Urban And Rural Coastal Landscapes Using Adcirc Generated Flood Data From Hurricanes Isaac And Laura, Katherine Faye Jones

LSU Master's Theses

Emergency managers rely on a variety on models and outputs, such as Hazards United States Multi- Hazard (Hazus-MH) and the Coastal Emergency Risk Assessment (CERA) visualization tool, to make decisions in the days leading up to and following hurricane events. This study focuses on using Hurricane Isaac (2012) and Hurricane Laura (2020).ASGS-CERA geoTIFFs, created from generated ADCIRC Prediction System data, in the Hazus-MH Flood Model to test using these two tools together in urban and rural areas. These ASGS-CERA integrated Hazus-MH studies were compared with Hazus-MH studies using the standard Hazus-MH surge methodology. They were tested for accuracy in both …

Blowout - Capping - Fracturing - Relief Well, A Full Cycle Workflow, Youssuf A. Elnoamany

LSU Master's Theses

Broaching is defined as the uncontrolled release of hydrocarbons to ocean seafloor after a loss of subsurface well control event. Failed attempts to cap the offshore wells undergoing worst case discharge may lead to hydraulic fracture initiation and subsequent propagation, leading to renewed release of hydrocarbon to the seafloor. During the capping stack shut-in process, pressure build-up will occur along the wellbore, exposing locations of possible fracture initiation to overpressurized fluid, such as directly below the casing shoe, and critical points along the well casing. Shall there be enough build-up pressure to exceed the minimum horizontal stress in an exposed …

Local Calibration Of Pavement Me And Performance Evaluation Of Pavement Rehabilitation And Preservation Asphalt Overlays In Louisiana, Farzana Moon

LSU Master's Theses

Asphalt overlays can be categorized as pavement rehabilitation structural overlays or pavement preservation overlays in terms of the thickness and timing of maintenance activities. Pavement rehabilitation overlay contributes to the structural enhancement of pavements and pavement preservation overlays generally provide functional improvement to an existing pavement. In recent times, the pavement design approach employed by the Louisiana Department of Transportation and Development (LADOTD) has been transitioning from the 1993 AASHTO design procedure to a locally calibrated Pavement ME method. The AASHTOWare Pavement ME (Mechanistic-Empirical) design procedure is considered the modern approach to pavement design. Significant updates have been introduced in …

Quantifying Discharge On The Lower Mississippi River Physical Model, Taylor S. Cagle

LSU Master's Theses

The Lower Mississippi River Physical Model (LMRPM) is a distorted, movable-bed physical model that replicates the hydraulics and bedload (sand) transport of the lower 195 miles of the Mississippi River. One year of flow and sediment transport on the prototype can be modeled in approximately one hour. With the ability to simulate long periods of time on the Lower Mississippi River in such a short time frame, the model can provide unique insight into subjects such as the potential effects from relative sea level rise on the lower river’s hydraulics and sediment transport. Quantifying discharge on the LMRPM is an …

Assessment Of Endogenous Biomass Decay As A Source Of Precursors For Microbially-Mediated Toluene And P-Cresol Production, Samuel J. Reynolds

LSU Master's Theses

The research reported in this thesis was conducted to investigate whether protein hydrolysis associated with endogenous decay of biomass produced following the addition of a readily fermentable substrate is a potential source of precursors that can ultimately be transformed to toluene and p-cresol in environments undergoing enhanced bioremediation.

A packed column intended to represent a laboratory-scale section of an aquifer was seeded with groundwater and then supplied with molasses-amended groundwater for a two-day interval. The injected molasses concentration and surface loading rate were selected to be representative of conditions in the vicinity of injection wells at a Superfund Site …

Variability In The Hamburg Wheel-Tracking Device (Hwtd) Data And Results, Ilerioluwa S. Giwa

LSU Master's Theses

Over the years, the Hamburg Wheel-Tracking Test (HWTT) has become one of the most popular devices used for characterizing asphalt mixtures for rutting potential and moisture susceptibility. However, although the HWTT is a reliable standard test for evaluating asphalt mixtures, it is not exempt from variability in the test data and result. Variability in the HWTT test data and results have been majorly attributed to imprecision in the test practice and due to some limitations in the HWT device setup.

The primary goal of this study is to evaluate the variability in the HWTT data and result by investigating a …

High Density Cement-Rock Interface Characterization, Zahid Farid

LSU Master's Theses

The strength and stability of a well depends primarily on the seal that is created between a geologic formation and a wellbore cement. To protect and maintain this well integrity during production and after well abandonment, fixed seals are installed in the wellbore. For this purpose, Portland cement of class H and G are used throughout the world as a plugging and sealing material for offshore oil and gas wells. The cement-rock interface is an area of vulnerability with a pathway that provides possible routes for leakage out into the wellbore environment and in the proximity of the seals. Therefore, …

Bio-Mediated Ground Improvement For Fine-Grained Soil, Guantao Cheng

LSU Master's Theses

The research explored the use of microbially induced carbonate precipitation (MICP) to improve the mechanical properties of fine-grained soil and rapidly repair soil cracks on embankment slopes. Slope failures are often induced by surface cracks on the embankment slopes. To date, most rapid repair methods for slope failures (e.g., geosynthetics, soil nails, plastic pins, and lime treatment, etc.) involve large earthwork, special installation equipment, and unique construction processes, which may require extended construction time, disturb traffic, or increase the total construction cost. This research explored the feasibility of using bio-cement (MICP) to improve soil mechanical properties, seal the soil cracks, …

Effects Of Historical Land-Use Change On Surface Runoff And Flooding In The Amite River Basin, Louisiana, Usa Using Coupled 1d/2d Hec-Ras–Hec-Hms Hydrological Modeling, Alexandre G. H. Cowles

LSU Master's Theses

The Amite River Basin is a largely rural watershed spanning parts of four counties in southern Mississippi and seven parishes in southeast Louisiana, with basinwide imperviousness increasing from 0.82% in 1938 to 3.85% in 2016. The Basin has been the subject of significant research interest since catastrophic flooding in 2016 caused 13 deaths and widespread damages. Rapid development in recent decades has led to an expansion of impervious surfaces in Baton Rouge and surrounding areas, encroaching on floodplains and wetlands. At the basin scale, differences in flooding due to impervious cover changes were found to be somewhat limited, particularly along …

Distance-Based Formation Control Using Decentralized Sensing With Infrared Photodiodes, Steven Williams

LSU Master's Theses

This study presents an onboard sensor system for determining the relative positions of mobile robots, which is used in decentralized distance-based formation controllers for multi-agent systems. This sensor system uses infrared photodiodes and LEDs; its effective use requires coordination between the emitting and detecting robots. A technique is introduced for calculating the relative positions based on photodiode readings, and an automated calibration system is designed for future maintenance. By measuring the relative positions of their neighbors, each robot is capable of running an onboard formation controller, which is independent of both a centralized controller and a global positioning-like system (e.g., …

Stream Power Analysis Of The Mid-Barataria Conveyance Channel Model, Jack Graham

LSU Master's Theses

Louisiana’s coast is disappearing at an alarming rate. Erosion, subsidence, sea level rise, and the devastating impacts from hurricanes have contributed to the loss of thousands of square miles of land that was once a thriving ecosystem. The Louisiana government is taking action to help protect and restore these coastal habitats, which are a home to some two million people and numerous species of animals, birds, and fish. The Mid-Barataria Sediment Diversion is a new type of project to help create land in Barataria Basin. Conceptually, the diversion is designed to use the available sediment and stream power provided by …

Operation Procedures Of Mid-Barataria Sediment Diversion Model To Reproduce Hydraulics And Sediment Transport, Chase Holston

LSU Master's Theses

The Lower Mississippi River Physical Model (LMRPM) is a distorted, movable bed model that simulates the hydraulics and sediment transport in the lower 195 miles of the Mississippi River. Carved into the model are both existing hydraulic structures, such as the Bonnet Carré Spillway, and proposed structures, such as the Mid-Barataria Sediment Diversion (MBSD). The MBSD will be the first sediment diversion built as part of Louisiana’s Coastal Master Plan, so incorporating the diversion in the LMRPM will be a useful tool to understanding how the diversion can impact the river hydraulics and bedload transport. The objective of this thesis …

Changes In Wetland Soil Processes And Ecosystem Functions Six Years After Marsh Creation In Barataria Bay, Louisiana, Erol R. Knaus

LSU Master's Theses

Louisiana contains about 40% of the conterminous United States coastal and estuarine wetlands but also has the highest rates of wetland loss at around 80% of the total. Approximately 4,900 km² of coastal land in Louisiana has been lost since 1930. Our study location, Barataria Bay, has one of the highest coastal wetland erosion rates in the nation, at ∼41 km² per year; and therefore, is a high priority for wetland restoration activities. In 2014, sandy sediment dredged from the bed of the Mississippi River was placed in Barataria Bay as part of a restoration effort. Samples were …

Emulsion Templating Application For Synthesis Of A Porous Zein Biocompatible Oil Adsorbent, Nathan Holley

LSU Master's Theses

The recovery of spilled oil from water sources using hydrophobic porous absorbent has gained significant interest due to the ease of implementation, large-scale adaptability, and robust nature of the technique. However, the lack of biodegradability of these synthetic adsorbents has caused concern of further contaminating the environment from the generation of microplastic waste that is known to persist and accumulate in the marine food chain and other ecosystems. To mitigate this potential hazard, a new biocompatible alternative is needed to replace the non-degradable synthetic materials currently used. This thesis presents ZEin-based Low Density porous Absorbent (ZELDA), synthesized using a particle …

Low-Cost Hardware-In-The-Loop (Hil) Simulator For Simulation And Analysis Of Embedded Systems With Non-Real-Time Applications, Chanuka S. Elvitigala

LSU Master's Theses

Hardware-In-the-Loop (HIL) simulation is an approach that is used for embedded systems testing which was popular in the early days of embedded systems. This technology was wrapped and was stored away for a long time. One of the main reasons is that the less use of embedded systems in society. Recent developments in embedded systems, data science, and control systems lead to a focus on testing these systems. The earliest method of testing these systems was by doing destructive testing which is a waste of money, resources, and time. The HIL provided a safe and economical way of testing the …