Engineering Commons^™

Multi-Factor Optimization Of Bio-Methanol Production Through Gasification Process Via Statistical Methodology Coupled With Genetic Algorithm, Amin Hedayati Moghaddam, Morteza Esfandyari, Dariush Jafari, Hossein Sakhaeinia

Department of Civil and Environmental Engineering: Faculty Publications

This work innovatively explores the bio-methanol production process, conducts comprehensive analyses, develops statistical models, and optimizes operational conditions, contributing valuable insights to the field of sustainable energy production from biomass. Accordingly, bio-methanol production from biomass through gasification route was investigated and simulated using Aspen Plus software. The effects of operational parameters on energy duty of gasification reactor and the methanol production rate in syngas to methanol reactor were investigated. The parameters affecting the process performance including temperature, pressure, and steam/feed ratio were examined using the response surface methodology (RSM) by central composite design (CCD) technique. Analysis of variance (ANOVA) was …

Multi-Factor Optimization Of Bio-Methanol Production Through Gasification Process Via Statistical Methodology Coupled With Genetic Algorithm, Amin Hedayati Moghaddam, Morteza Esfandyari, Dariush Jafari, Hossein Sakhaeinia

Department of Civil and Environmental Engineering: Faculty Publications

This work innovatively explores the bio-methanol production process, conducts comprehensive analyses, develops statistical models, and optimizes operational conditions, contributing valuable insights to the field of sustainable energy production from biomass. Accordingly, bio-methanol production from biomass through gasification route was investigated and simulated using Aspen Plus software. The effects of operational parameters on energy duty of gasification reactor and the methanol production rate in syngas to methanol reactor were investigated. The parameters affecting the process performance including temperature, pressure, and steam/feed ratio were examined using the response surface methodology (RSM) by central composite design (CCD) technique. Analysis of variance (ANOVA) was …

Power-Over-Tether Unmanned Aerial System Leveraged For Trajectory Influenced Atmospheric Sensing, Daniel Rico

Department of Computer Science and Engineering: Dissertations, Theses, and Student Research

The use of unmanned aerial systems (UASs) in agriculture has risen in the past decade and is helping to modernize agriculture. UASs collect and elucidate data previously difficult to obtain and are used to help increase agricultural efficiency and production. Typical commercial off-the-shelf (COTS) UASs are limited by small payloads and short flight times. Such limits inhibit their ability to provide abundant data at multiple spatiotemporal scales. In this thesis, we describe the design and construction of the tethered aircraft unmanned system (TAUS), which is a novel power-over-tether UAS configured for long-term, high throughput atmospheric monitoring with an array of …

An End-To-End Trainable Method For Generating And Detecting Fiducial Markers, J Brennan Peace

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Existing fiducial markers are designed for efficient detection and decoding. The methods are computationally efficient and capable of demonstrating impressive results, however, the markers are not explicitly designed to stand out in natural environments and their robustness is difficult to infer from relatively limited analysis. Worsening performance in challenging image capture scenarios - such as poorly exposed images, motion blur, and off-axis viewing - sheds light on their limitations. The method introduced in this work is an end-to-end trainable method for designing fiducial markers and a complimentary detector. By introducing back-propagatable marker augmentation and superimposition into training, the method learns …

A Quantile-Based Approach For Transmission Expansion Planning, Jairo Cervantes, F. Fred Choobineh

Department of Electrical and Computer Engineering: Faculty Publications

Transmission expansion planning is an integral part of power system planning and consists of generating and selecting transmission proposals for maintaining sufficient transmission capacity to satisfy the electric load. Specifically, the desire to increase the use of renewable energy has exposed the limitations of transmission networks and has elevated the importance of transmission expansion planning. However, considering the random nature of renewable sources in conjunction with the power outages makes the planning process very challenging. We present a new procedure for selecting the best transmission enhancement proposal from a set of finite proposals under uncertainty. The selection is based on …

Domain Adaptation In Unmanned Aerial Vehicles Landing Using Reinforcement Learning, Pedro Lucas Franca Albuquerque

Department of Computer Science and Engineering: Dissertations, Theses, and Student Research

Landing an unmanned aerial vehicle (UAV) on a moving platform is a challenging task that often requires exact models of the UAV dynamics, platform characteristics, and environmental conditions. In this thesis, we present and investigate three different machine learning approaches with varying levels of domain knowledge: dynamics randomization, universal policy with system identification, and reinforcement learning with no parameter variation. We first train the policies in simulation, then perform experiments both in simulation, making variations of the system dynamics with wind and friction coefficient, then perform experiments in a real robot system with wind variation. We initially expected that providing …

Effect Of Limited Water Supplies On Center Pivot Performance, Derrel Martin, Derek M. Heeren, Steve Melvin, Troy Ingram

Department of Biological Systems Engineering: Conference Presentations and White Papers

When appropriately designed and operated, center pivot irrigation systems can efficiently irrigate many crops grown on diverse soil and terrain conditions. However, a significant number of pivots are not supplied with an adequate water to operate as envisioned.

We simulated the hydraulics of a center pivot irrigation system, including the pump curve, flow rate, pipeline hydraulics, pressure regulators, nozzle flow rate, and irrigation application uniformity. This was used to analyse the performance of a center pivot for a sloping field for both adequate and inadequate water flow rate. The performance was simulated for a range of inlet pressures when pressure …

Effects Of Moving Bottlenecks On Traffic Operations On Four-Lane Level Freeway Segments, Jianan Zhou

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The Highway Capacity Manual (HCM) was developed to provide capacity and level of service analyses for roadway facilities. Trucks may adversely affect the quality of traffic flow on a roadway. In HCM, the passenger car equivalent (PCE) of a truck, which represents the number of passenger cars that have an equivalent effect on traffic flow, is used to account for the impacts of trucks. However, in the past ten years rural freeways in the western rural U.S. have experienced conditions that lie outside the standard HCM conditions. Also, the current HCM truck PCEs may not be appropriate for the western …

Development Of Iowa Dot Combination Bridge Separation Barrier With Bicycle Railing, Chaz M. Ginger

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The Iowa Department of Transportation typically builds separation barriers between vehicle and pedestrian/bicycle facilities when sidewalks or trails are present on vehicular bridges. Currently, Iowa DOT employs a combination bridge rail that utilizes a concrete parapet that previously had been successfully evaluated to National Cooperative Highway Research Program (NCHRP) Report 350 Test Level 4 (TL-4) criteria for these situations. While the parapet had been successfully evaluated, the combination bridge rail system as a whole had not been evaluated to any crash test standards. Iowa DOT desired that researchers at Midwest Roadside Safety Facility (MwRSF) design and test a combination bridge …

Ring And Peg Simulation For Minimally Invasive Surgical Robot, Evan Brown

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Surgical procedures utilizing minimally invasive laparoscopic techniques have shown less complications, better cosmetic results, and less time in the hospital than conventional surgery. These advantages are partially offset by inherent difficulties of the procedures which include an inverted control scheme, instrument clashing, and loss of triangulation. Surgical robots have been designed to overcome the limitations, the Da Vinci being the most widely used. A dexterous in vivo, two-armed robot, designed to enter an insufflated abdomen with a limited insertion profile and expand to perform a variety of operations, has been created as a less expensive, versatile alternative to the Da …

Design And Implementation Of A Stand-Alone Tool For Metabolic Simulations, Milad Ghiasi Rad

Department of Computer Science and Engineering: Dissertations, Theses, and Student Research

In this thesis, we present the design and implementation of a stand-alone tool for metabolic simulations. This system is able to integrate custom-built SBML models along with external user’s input information and produces the estimation of any reactants participating in the chain of the reactions in the provided model, e.g., ATP, Glucose, Insulin, for the given duration using numerical analysis and simulations. This tool offers the food intake arguments in the calculations to consider the personalized metabolic characteristics in the simulations. The tool has also been generalized to take into consideration of temporal genomic information and be flexible for simulation …

Investigating Students’ Perception Using Construction Management Simulations, Saeed Rokooei, James D. Goedert, Asregedew Woldesenbet

Department of Construction Engineering and Management: Faculty Publications

Today, construction programs are incorporating a wide variety of active learning methods in their curricula to improve student learning outcomes and induce a more knowledge retention rate. Simulations and educational games are one of the fast growing and effective active learning methods that have been implemented in many programs. However, there are few instances of such learning methods applied in construction programs and a limited number of research projects have been conducted to investigate short-term and long-term outcomes of these methods and applications. This paper presents construction students’ perceptions of tested simulations with regards to the features, knowledge gained, level …

Development Of A Transition Between An Energy-Absorbing Concrete Barrier And A Rigid Concrete Buttress, Tyler Schmidt

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

From 2010 to 2015, MwRSF researchers developed the RESTORE barrier, which is a restorable MASH TL-4 median barrier with a steel and concrete rail supported by elastomer posts and steel skids. The research effort reported herein describes the initial development of a transition from the RESTORE barrier to a rigid TL-4 concrete buttress.

The previously-developed RESTORE barrier LS-DYNA model was validated against three full-scale vehicle crash tests. Several design concepts were generated through a series of brainstorming efforts. The primary transition concept consisted of a pin and loop connection between the RESTORE barrier and rigid concrete buttress, which was designed …

Fundamental Problems In Porous Materials: Experiments & Computer Simulation, Zhanping Xu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Porous materials have attracted massive scientific and technological interest because of their extremely high surface-to-volume ratio, molecular tunability in construction, and surface-based applications. Through my PhD work, porous materials were engineered to meet the design in selective binding, self-healing, and energy damping. For example, crystalline MOFs with pore size spanning from a few angstroms to a couple of nanometers were chemically engineered to show 120 times more efficiency in binding of large molecules. In addition, we found building blocks released from those crystals can be further patched back through a healing process at ambient and low temperatures down to -56 …

Simulation And Validation Of Radio Frequency Heating Of Shell Eggs, Soon Kiat Lau

Department of Food Science and Technology: Dissertations, Theses, and Student Research

Finite element models were developed with the purpose of finding an optimal radio frequency (RF) heating setup for pasteurizing shell eggs. Material properties of the yolk, albumen, and shell were measured and fitted into equations that were used as inputs for the model. When the egg was heated by itself, heating tend to be focused at the air cell to result in a “coagulation ring.” The focused heating near the air cell of the egg prevented satisfactory pasteurization of the egg, but deeper analysis of the simulation results offered a new perspective on how non-uniform RF heating could occur in …

Estimation Of Optimal Productivity In Labor-Intensive Construction Operations, Krishna Prasad Kisi

Department of Construction Engineering and Management: Dissertations, Theses, and Student Research

In an attempt to evaluate the efficiency of labor-intensive construction operations, project managers typically compare actual with historical productivity for equivalent operations. However, this approach toward examining productivity only provides a relative benchmark for efficiency and may lead to the characterization of operations as objectively efficient when in reality such operations might simply be comparably efficient.

Optimal productivity is the highest sustainable productivity achievable under good management and typical field conditions. Optimal productivity is useful in the determination of the absolute efficiency of construction operations because an accurate estimate of optimal labor productivity allows for the comparison of actual vs. …

Measuring Autonomy And Solving General Stabilization Problems With Multi-Agent Systems, Rasheed A. Rajabzadeh

Department of Computer Science and Engineering: Dissertations, Theses, and Student Research

Many distributed complex problems address a particular form of resource scheduling where proper resource management can cut costs by stabilizing a set of stochastic fluctuating parameters. Wireless sensor network communication, supply chain management, stock trading, intelligent traffic management, and smart grid systems are examples of these problems. Among the various solutions, a common strategy often used to address this type of problems is fluctuation reduction via resource buffering combined with load shifting. Respectively, stable wireless communication, demand for supplies, liquidity, traffic speed, and power demand reduce cost and can be achieved by properly managing sensor data buffers, warehouses, capital, distance …

Simulation, Development And Deployment Of Mobile Wireless Sensor Networks For Migratory Bird Tracking, William P. Bennett Jr

Department of Computer Science and Engineering: Dissertations, Theses, and Student Research

This thesis presents CraneTracker, a multi-modal sensing and communication system for monitoring migratory species at the continental level. By exploiting the robust and extensive cellular infrastructure across the continent, traditional mobile wireless sensor networks can be extended to enable reliable, low-cost monitoring of migratory species. The developed multi-tier architecture yields ecologists with unconventional behavior information not furnished by alternative tracking systems at such a large scale and for a low-cost. The simulation, development and implementation of the CraneTracker software system is presented. The system is shown effective through multiple proxy deployments on wildlife and has been operational for 10 months …

Improving Health Care Quality And Safety: The Development And Assessment Of Laparoscopic Surgery Instrumentation, Practices And Procedures, Bernadette Mccrory

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Adverse events due to medical errors are a leading cause of death in the United States exceeding the mortality rates of motor vehicle accidents, breast cancer and AIDS. Improvements can and should be made to reduce the rates of preventable surgical errors since they account for nearly half of all adverse events within hospitals. Although minimally invasive surgery has proven patient benefits such as reduced postoperative pain and hospital stay, its operative environment imposes substantial physical and cognitive strain on the surgeon increasing the risk of error. In order to mitigate errors and protect patients, a multidisciplinary approach was taken …

A 3-D Computational Fluid Dynamics Model For Forced Air Cooling Of Eggs Placed In Trays, Vikas Kumar, Ai Pheeng Wee, Sohan Birla, Jeyamkondan Subbiah, Harshanardhan Thippareddi

Biological Systems Engineering: Papers and Publications

Shell eggs must be cooled quickly after laying for controlling Salmonella Enteritidis (SE) growth. To fulfill a research need identified by Food Safety and Inspection Service (FSIS), a 3-D Computational Fluid Dynamics (CFD) model was developed to predict the temperature of eggs placed on a tray (6 rows × 5 columns) under forced air cooling. The continuity, momentum, and energy equations were solved along with standard k-ε turbulence model using PHOENICS software. The model was validated by conducting experiments in a wind tunnel at various air temperatures (7–11 °C) and velocities (0.3– 0.7 m/s). Root mean square error for predicting …

Synthesis And Characterization Of Highly Textured Pt–Bi Thin Films, Xingzhong Li, Parashu Kharel, Shah R. Valloppilly, David J. Sellmyer

Nebraska Center for Materials and Nanoscience: Faculty Publications

Pt–Bi films were synthesized on glass and thermally oxidized silicon substrates by e-beam evaporation and annealing. The structures were characterized using X-ray diffraction (XRD) and transmission electron microscopy/selected area electron diffraction (TEM/SAED) techniques. Single-phase PtBi was obtained at an annealing temperature of 300°C, whereas a higher annealing temperature of 400°C was required to obtain the highly textured γ-PtBi2 phase. TEM/SAED analysis showed that the films annealed at 400°C contain a dominant γ-PtBi2 phase with a small amount of β-PtBi2 and α-PtBi2 phases. Both the PtBi and γ-PtBi2 phases are highly textured in these two kinds of film: the c-axis of …

Simulation And Control System Of A Railroad Track Power Harvesting Device, Kyle J. Phillips

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

With the vastness of existing railroad infrastructure, there exist numerous road crossings which are lacking warning light systems and/or crossing gates due to their remoteness from existing electrical infrastructure. Along with lacking warning light systems, these areas also tend to lack distributed sensor networks used for railroad track health monitoring applications. With the power consumption required by these systems being minimal, extending electrical infrastructure into these areas would not be an economical use of resources. This motivated the development of an energy harvesting solution for remote railroad deployment.

This thesis describes a computer simulation created to validate experimental on-track results …

Using Thermally Coupled Reactive Distillation Columns In Biodiesel Production, Nghi Nguyen, Yaşar Demirel

Yaşar Demirel Publications

Production of ethyl dodecanoate (biodiesel) using lauric acid and methanol with a solid acid catalyst of sulfated zirconia is studied by using two distillation sequences. In the first sequence, the methanol recovery column follows the reactive distillation column. In the second sequence, the reactive distillation and methanol recovery columns are thermally coupled. Thermally coupled distillation sequences may consume less energy by allowing interconnecting vapor and liquid streams between the two columns to elminate reboiler or condenser or both. Here we study the thermally coupled side-stripper reactive distillation and eliminate the condenser of the reactive distillation column. Both the sequences are …

Soil Behavior Under Blast Loading, Jichong An

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Understanding the behavior of soil under blast loading is very important to engineers in mining, tunneling, and military construction. Due to the very complex structure of a soil mass it is very difficult to describe its constitutive relation, especially when it has different water contents and it is under blast loading conditions. New protective system designs subjected to blast loading need to be proved its validation prior to predict effect of explosive before implementation. Full-scale, buried explosive tests are costly. Finite element simulations play a significant role in the design of protective systems, for example a bottom platform of lightweight …

Course Portfolio - Discrete Event Simulation, Paul Savory

Department of Industrial and Management Systems Engineering: Faculty Publications

This course portfolio, written by Dr. Paul Savory, provides an overview of his Discrete Event Simulation course at the University of Nebraska-Lincoln. It offers an overview of the course goals, a summary of the classroom activities for achieving them, and a detailed assessment of student learning. He highlights his introduction of the simul8 programming environment to his students. In addition to exploring his students’ learning, Dr. Savory also explores different approaches for documenting his teaching by including multimedia clips (video and audio), uses graphs, uses color, and incorporates images. The resulting portfolio is one that can be reviewed, shared, and …

Simulation Of Corn Stover And Distillers Grains Gasification With Aspen Plus, Ajay Kumar, Hossein Noureddini, Yaşar Demirel, David Jones, Milford Hanna

Yaşar Demirel Publications

A model was developed to simulate the performance of a lab‐scale gasifier and predict the flowrate and composition of product from given biomass composition and gasifier operating conditions using Aspen Plus software. Mass balance, energy balance, and minimization of Gibbs free energy during the gasification were applied to determine the product gas composition. Carbon conversion efficiency and tar content were provided to the model as inputs as these could not be predicted by the model based on minimization of Gibbs free energy. Experiments for validation of the model were performed on a lab‐scale fluidized bed gasifier using corn stover and …

Details And Description Of Operations Research, Paul Savory

Industrial and Management Systems Engineering: Reports

The ambiguous term operations research was coined during World War II. A frequent substitute is management science. Operations research is a scientific approach to analyzing problems and making decisions. It uses mathematics and mathematical modeling on computers to forecast the implications of various choices and zero in on the best alternatives. This content paper provides an overview of operations research. It highlights operations research problems, methods for solving problems, different areas of operations research, and example problems.

Finite Element Analysis Of Covered Microstents, Linxia Gu, Swadeshmukul Santra, Robert A. Mericle, Ashok V. Kumar

Department of Mechanical and Materials Engineering: Faculty Publications

Currently available neuroendovascular devices are inadequate for effective treatment of many wide-necked or fusiform intracranial aneurysms and intracranial carotid-cavernous fistulae (CCF). Placing a covered microstent across the intracranial aneurysm neck and CCF rent could restore normal vessel morphology by preventing blood flow into the aneurysm lumen or CCF rent. To fabricate covered microstents, our research group has developed highly flexible ultra thin (~150 μm) silicone coverings and elastomerically captured them onto commercially available metal stents without stitching. Preliminary in vivo studies were conducted by placing these covered microstents in the common carotid artery of rabbits. The feasibility of using covered …

A Template-Based Conceptual Modeling Infrastructure For Simulation Of Physical Security Systems, Ashu Guru, Paul Savory

Department of Industrial and Management Systems Engineering: Faculty Publications

Although simulation is one of the most innovative and cost-effective tools for modeling and analyzing a system, simulation studies often fail to provide any useful results. One reason is attributed to the fact that model formulation depends on the skills of the analyst. This paper describes a research to develop a conceptual modeling infrastructure to assist a simulation analyst in specifying components for studying physical security systems. The modeling framework has been programmed as an internet-based web application. Using the application, the successful development and implementation of a physical security simulation model will be aided by a defined scientific methodology …

A Template-Based Conceptual Modeling Infrastructure For Simulation Of Physical Security Systems, Paul Savory

Department of Industrial and Management Systems Engineering: Faculty Publications

Although simulation is one of the most innovative and cost-effective tools for modeling and analyzing a system, simulation studies often fail to provide any useful results. One reason is attributed to the fact that model formulation depends on the skills of the analyst. This paper describes a research to develop a conceptual modeling infrastructure to assist a simulation analyst in specifying components for studying physical security systems. The modeling framework has been programmed as an internet-based web application. Using the application, the successful development and implementation of a physical security simulation model will be aided by a defined scientific methodology …