Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 19 of 19
Full-Text Articles in Engineering
Risk Assessment Of Hazardous Material Transportation For Small And Tribal Communities, Harrison Redepenning
Risk Assessment Of Hazardous Material Transportation For Small And Tribal Communities, Harrison Redepenning
Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research
By and large transportation of hazardous materials (HazMat) across the US is increasing, with truck transportation as the most common method of transport. Smaller communities (population <5,000) and Native American communities often lack the economic and political influence to quantify the dangers that HazMat incidents present to the immediate and surrounding areas. Lack of such information is an impediment to adequate preparedness in cases of HazMat incidents. This research focuses on assessing the vulnerability of small and tribal communities in Nebraska to the impacts of highway HazMat incidents. This was done by estimating the expected number and type of HazMat incidents per population in each community. Additionally, statistical analysis was conducted on actual HazMat incidents to determine if small and Native American communities experience a higher rate of incidents per population and per HazMat VMT than large and other small communities respectively. For per population, it was found small versus large is statistically significant while Native American versus other small communities was not significant. For per HazMat VMT, neither comparison was found to be statistically significant. In estimated HazMat incidents, actual HazMat incidents per population, and actual HazMat incidents per HazMat VMT, small communities had higher mean values than their large counterparts. Communities on Native American reservation land experienced a higher estimated and lower actual HazMat incident rate per population than other small communities. For actual HazMat incidents per VMT, Native American communities had a higher rate than other small communities.
Advisor: Aemal Khattak
Evaluation Of Tie-Bar Anchoring Methods: Non-Shrink Grout Vs. Epoxy, Wally Heyen, Lieska Halsey, Tim Krason, Brandon Varilek, David Hansen
Evaluation Of Tie-Bar Anchoring Methods: Non-Shrink Grout Vs. Epoxy, Wally Heyen, Lieska Halsey, Tim Krason, Brandon Varilek, David Hansen
Nebraska Department of Transportation: Research Reports
Tie bars are epoxy coated steel bars that connect the longitudinal joints in concrete pavement. Tie bars prevent faulting and joint separation between lanes Tie bars can be placed into the plastic concrete or inserted after curing by drilling and anchoring with epoxy or non-shrink grout. The specification for the tie bars requires the use of a No. 5 bar, 18 inches long and shall meet ASTM A775 / A775M [1], Section 1020.The Nebraska Department of Transportation “Standard Specifications for Highway Construction,” (Section 603.03) requires contractors to mechanically insert tie bars into the face of pavements during construction. Tie bars …
Long-Term Performance Evaluation Of Nudeck In Kearney East Bypass, George Morcous, Marc Maguire
Long-Term Performance Evaluation Of Nudeck In Kearney East Bypass, George Morcous, Marc Maguire
Nebraska Department of Transportation: Research Reports
The Kearney East Bypass bridge is the first project that implements the newly developed precast concrete deck system (known as 2nd generation NUDECK). The new system consists of full-depth full-width precast prestressed concrete deck panels that are 12 ft (3.66 m) long each. The panels have covered shear pockets at 4 ft (1.22 m) spacing on each girder line to host clustered shear connectors that are adjustable in height. Narrow unreinforced transverse joints are used to eliminate the need for deck overlay. Also, deck panels are post-tensioned in the longitudinal direction using a new post-tensioning system that eliminates the need …
Performance Evaluation Of Inverted Tee (It) Bridge System, Garrett P. Martindale, Daniel Watson, Antony Mohsen Kamal Masoud Kodsy, Mostafa Abo El-Khier, Richard L. Wood, George Morcous
Performance Evaluation Of Inverted Tee (It) Bridge System, Garrett P. Martindale, Daniel Watson, Antony Mohsen Kamal Masoud Kodsy, Mostafa Abo El-Khier, Richard L. Wood, George Morcous
Nebraska Department of Transportation: Research Reports
The Inverted Tee (IT) girder bridge system was originally developed in 1996 by the University of Nebraska–Lincoln (UNL) researchers and Nebraska Department of Transportation (NDOT) engineers. This bridge system currently accounts for over 110 bridges in Nebraska used for both state highways and local county roads. Extensive longitudinal and transverse deck cracking have been observed and noted in numerous bridge inspection reports. Since the IT girder bridge system is relatively new, limited data and knowledge exist on its structural performance and behavior. This study evaluates the IT girder bridge system by conducting twenty field observations as well as recording accelerometer, …
Restricted Crossings On Rural Highways, John Sangster, Tim Adams
Restricted Crossings On Rural Highways, John Sangster, Tim Adams
Nebraska Department of Transportation: Research Reports
This study examines the potential for replacing the standard intersection design at two-way stop control (TWSC) and all- way stop control (AWSC) intersections along rural highways with a roundabout or a restricted crossing u-turn (RCUT) facility. The geometry of the RCUT design prohibits left and through movements from the side road, and provides a u-turn location downstream from the main crossing. This type of facility has been implemented for rural highways extensively in both Maryland and North Carolina, as well as in limited cases in many other states such as Minnesota and Missouri, with the potential to serve as a …
34-Inch Tall Three Beam Transition To Concrete Buttress, Scott Rosenbaugh, Wyatt Fallet, Ronald K. Faller, Robert W. Bielenberg, Jennifer Schmidt
34-Inch Tall Three Beam Transition To Concrete Buttress, Scott Rosenbaugh, Wyatt Fallet, Ronald K. Faller, Robert W. Bielenberg, Jennifer Schmidt
Nebraska Department of Transportation: Research Reports
Roadway resurfacing and overlay projects effectively reduce the height of roadside barriers placed adjacent to the roadway, which can negatively affect their crashworthiness. More recently, bridge rails and concrete barriers have been installed with slightly increased heights to account for future overlays. However, adjacent guardrails and approach transitions have not yet been modified to account for overlays. The objective of this project was to develop an increased-height, approach guardrail transition (AGT) to be crashworthy both before and after roadway overlays of up to 3 in. (76 mm).
A 34-in. (864-mm) tall, thrie beam transition was designed such that the system …
Validation Of The Mechanical Rocker Test Method For Ice Melting Capacity (Mrt-Imc), Lieska Halsey, David Hansen
Validation Of The Mechanical Rocker Test Method For Ice Melting Capacity (Mrt-Imc), Lieska Halsey, David Hansen
Nebraska Department of Transportation: Research Reports
The anti-icing and deicing industry has interest in the development of an objective, repeatable test procedure for the evaluation and comparison of anti-icing and deicing products. Pursuant to this goal, the Nebraska Department of Transportation (NDOT) funded research at the University of Nebraska-Lincoln (UNL) to investigate methods for evaluating deicing products, beginning in 2011[1]. Researchers at UNL developed the procedure for the Mechanical Rocker Test for Ice Melting Capacity (MRT or MRT-IMC) in 2014[2].
From 2017-2019, NDOT evaluated the MRT-IMC procedure for validity and suitability as a standard test procedure for assessing deicer performance. NDOT also explored opportunities to improve …
Mash Test No. 3-10 Of A Non-Proprietary, High-Tension, Cable Median Barrier For Use In 6h:1v V-Ditch (Test No. Mwp-9), Mojdeh Asadollahi Pajouh, Karla A. Lechtenberg, Ronald K. Faller, James C. Holloway, Robert W. Bielenberg, Scott K. Rosenbaugh
Mash Test No. 3-10 Of A Non-Proprietary, High-Tension, Cable Median Barrier For Use In 6h:1v V-Ditch (Test No. Mwp-9), Mojdeh Asadollahi Pajouh, Karla A. Lechtenberg, Ronald K. Faller, James C. Holloway, Robert W. Bielenberg, Scott K. Rosenbaugh
Nebraska Department of Transportation: Research Reports
The Midwest Pooled Fund Program has been developing a prototype design for a non-proprietary, high-tension, cable median barrier for use in a 6H:1V median V-ditch. This system incorporates four evenly spaced cables, Midwest Weak Posts (MWPs) spaced at 8 to 16 ft (2.4 to 4.9 m) intervals, and a bolted, tabbed bracket to attach the cables to each post. Full-scale crash testing was needed to evaluate the barrier’s safety performance. According to the Manual for Assessing Safety Hardware 2016 (MASH) testing matrix for cable barriers installed within a 6H:1V median V-ditch, a series of eight full-scale crash tests are required …
Hot Applied Sealant Bond Test For Joints With Penetrating Sealers, Lieska Halsey
Hot Applied Sealant Bond Test For Joints With Penetrating Sealers, Lieska Halsey
Nebraska Department of Transportation: Research Reports
Recently a concern has been raised for hot applied sealant bond for joints with penetrating sealers. The objective of this study will be to determine if the bond between the sealant and the concrete is compromised by the sealer currently approved to be used in Nebraska. The expected results will be that the bond is not compromised and is serving for the expected joint service life.
Compressive Strength Of Concrete Cylinders By Different Preparation Methods: Sulphur, Neoprene Pads And Grinding, Wally Heyen, Lieska Halsey
Compressive Strength Of Concrete Cylinders By Different Preparation Methods: Sulphur, Neoprene Pads And Grinding, Wally Heyen, Lieska Halsey
Nebraska Department of Transportation: Research Reports
The purpose of this evaluation is to compare the effects of four types of cylinder preparation methods prior to compressive strength testing in accordance to ASTM C 39.
Effectiveness Of Chain Link Turtle Fence And Culverts In Reducing Turtle Mortality And Providing Connectivity Along U.S. Hwy 83, Valentine National Wildlife Refuge, Nebraska, Usa, Marcel P. Huijser, Kari E. Gunson, Elizabeth R. Fairbank
Effectiveness Of Chain Link Turtle Fence And Culverts In Reducing Turtle Mortality And Providing Connectivity Along U.S. Hwy 83, Valentine National Wildlife Refuge, Nebraska, Usa, Marcel P. Huijser, Kari E. Gunson, Elizabeth R. Fairbank
Nebraska Department of Transportation: Research Reports
We evaluated the effectiveness of existing turtle fences through collecting and analyzing turtle mortality data along U.S. Hwy 83, in and around Valentine National Wildlife Refuge, Nebraska, USA. We also investigated the level of connectivity for turtles provided through the culverts that were originally designed to pass water through a capture-mark-recapture experiment. While fenced valley sections had 33.1% fewer turtle observations than unfenced valley sections, the difference was not significant. However, we think that the effectiveness of the fence can be improved through fence repairs, other modifications of the fences, vegetation maintenance, and extending the length of the fences. Four …
Evaluation Of Opportunities And Challenges Of Using Inrix Data For Real-Time Performance Monitoring And Historical Trend Assessment, Anuj Sharma, Vesal Ahsani, Sandeep Rawat
Evaluation Of Opportunities And Challenges Of Using Inrix Data For Real-Time Performance Monitoring And Historical Trend Assessment, Anuj Sharma, Vesal Ahsani, Sandeep Rawat
Nebraska Department of Transportation: Research Reports
In recent years there has been a growing desire for the use of probe vehicle technology for congestion detection and general infrastructure performance assessment. Unlike costly traditional data collection by loop detectors, wide-area detection using probe-sourced traffic data is significantly different in terms of measurement technique, pricing, coverage, etc. This affects how the new technology is applied and used to solve current traffic problems such as traffic incident management and roadway performance assessment. This report summarizes the experiences and lessons learned while using probe data for traffic operations and safety management in the state of Nebraska and makes recommendations for …
Assessing Passenger Car Equivalency Factors For High Truck Percentages, Jianan Zhou, Laurence Rilett, Elizabeth Jones
Assessing Passenger Car Equivalency Factors For High Truck Percentages, Jianan Zhou, Laurence Rilett, Elizabeth Jones
Nebraska Department of Transportation: Research Reports
The Passenger Car Equivalent (PCE) values in the Highway Capacity Manual (HCM) 2010 might not be valid for western Nebraska freeway conditions. This is because: 1) Interstate 80 (I-80) experiences high truck percentages (25% to 60%), while the HCM provides PCE values up to 25% of the truck percentage; 2) the average speed of trucks are observed lower than passenger cars, which is incompatible with the HCM assumption that the free speed of all vehicle types is the same at level terrain; and 3) it is unclear whether the “average” truck used in the simulation study for PCE values in …
Use Of Recycled Crushed Concrete (Rcc) Fines For Potential Soil Stabilization, Lindeman Mark, Varilek Brandon, Lieska Halsey, Rick Gloe, Maria Olomi
Use Of Recycled Crushed Concrete (Rcc) Fines For Potential Soil Stabilization, Lindeman Mark, Varilek Brandon, Lieska Halsey, Rick Gloe, Maria Olomi
Nebraska Department of Transportation: Research Reports
This study evaluated the use of Recycled Crushed Concrete (RCC) Fines for potential soil stabilization. Soil stabilization is the enhancement of subgrade stability to improve the constructability of successive pavement layers. Use of RCC fines may not only provide less costly alternatives for subgrade stabilization, but their use may also alleviate landfill disposal challenges.
Fertilizer Effects On Attaining Vegetation Requirements, Walter H. Schacht, Carol Wienhold
Fertilizer Effects On Attaining Vegetation Requirements, Walter H. Schacht, Carol Wienhold
Nebraska Department of Transportation: Research Reports
No abstract provided.
Establishing Permanent Vegetation After Highway Construction, John C. Soper, Walter H. Schacht
Establishing Permanent Vegetation After Highway Construction, John C. Soper, Walter H. Schacht
Nebraska Department of Transportation: Research Reports
No abstract provided.
Dynamic Vulnerability Assessment Of Highway And Railway Bridges, Mehdi Mohseni
Dynamic Vulnerability Assessment Of Highway And Railway Bridges, Mehdi Mohseni
Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research
Dynamic loads can cause severe damage to bridges, and lead to malfunction of transportation networks. A comprehensive understanding of the nature of the dynamic loads and the structural response of bridges can prevent undesired failures while keeping the cost-safety balance. Dissimilar to the static behavior, the dynamic response of bridges depends on several structural parameters such as material properties, damping and mode shapes. Furthermore, dynamic load characteristics can significantly change the structural response. In most cases, complexity and involvement of numerous parameters require the designer to investigate the bridge response via a massive numerical study.
This dissertation targets three main …
Analysis Of Existing Work-Zone Sign Supports Using Manual For Assessing Safety Hardware Safety Performance Criteria, Jennifer D. Schmidt, Ronald K. Faller, Karla A. Lechtenberg, Dean L. Sicking
Analysis Of Existing Work-Zone Sign Supports Using Manual For Assessing Safety Hardware Safety Performance Criteria, Jennifer D. Schmidt, Ronald K. Faller, Karla A. Lechtenberg, Dean L. Sicking
Department of Civil and Environmental Engineering: Faculty Publications
Over the years, numerous work-zone, portable sign support systems have been successfully crash tested according to the Test Level 3 safety performance guidelines provided in the National Cooperative Highway Research Program Report 350 and accepted for use along our nation’s highways. For this study, several crashworthy sign support systems were analyzed to predict their safety performance according to the new evaluation criteria provided in the Manual for Assessing Safety Hardware (MASH). More specifically, this analysis was conducted to determine which hardware parameters negatively affect a system’s safety performance. To verify the accuracy of the analysis, eight systems, four with the …
Evaluation Of A Modified Three Cable Guardrail Adjacent To Steep Slope, Ryan J. Terpsma, Dean L. Sicking, Karla A. Polivka, John R. Rohde, Ronald K. Faller, John D. Reid
Evaluation Of A Modified Three Cable Guardrail Adjacent To Steep Slope, Ryan J. Terpsma, Dean L. Sicking, Karla A. Polivka, John R. Rohde, Ronald K. Faller, John D. Reid
Nebraska Department of Transportation: Research Reports
No abstract provided.