Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons

Open Access. Powered by Scholars. Published by Universities.®

Articles 1 - 4 of 4

Full-Text Articles in Engineering

Safety Considerations For All Road Users On Edge Lane Roads, Michael Williams, Marcial Lamera, Aleksander Bauranov, Carole Voulgaris, Anurag Pande Mar 2021

Safety Considerations For All Road Users On Edge Lane Roads, Michael Williams, Marcial Lamera, Aleksander Bauranov, Carole Voulgaris, Anurag Pande

Mineta Transportation Institute

Edge lane roads (ELRs), also known as advisory bike lanes or advisory shoulders, are a type of shared street where two-way motor vehicle (MV) traffic shares a single center lane, and edge lanes on either side are preferentially reserved for vulnerable road users (VRUs). This work comprises a literature review, an investigation of ELRs’ operational characteristics and potential road user interactions via simulation, and a study of crash data from existing American and Australian ELRs.

The simulation evaluated the impact of various factors (e.g., speed, volume, directional split, etc.) on ELR operation. Results lay the foundation for a siting criterion. …


Modeling Operational Performance Of Urban Roads With Heterogeneous Traffic Conditions, Swapneel R. Kodupuganti, Sonu Mathew, Srinivas S. Pulugurtha Jan 2021

Modeling Operational Performance Of Urban Roads With Heterogeneous Traffic Conditions, Swapneel R. Kodupuganti, Sonu Mathew, Srinivas S. Pulugurtha

Mineta Transportation Institute

The rapid growth in population and related demand for travel during the past few decades has had a catalytic effect on traffic congestion, air quality, and safety in many urban areas. Transportation managers and planners have planned for new facilities to cater to the needs of users of alternative modes of transportation (e.g., public transportation, walking, and bicycling) over the next decade. However, there are no widely accepted methods, nor there is enough evidence to justify whether such plans are instrumental in improving mobility of the transportation system. Therefore, this project researches the operational performance of urban roads with heterogeneous …


Development Of Reduced Chemical Kinetic Models For The Numerical Simulation Of Combustion And Emissions Behavior Of Representative Conventional And Bio-Derived Fuels, Mazen A. Eldeeb Jun 2020

Development Of Reduced Chemical Kinetic Models For The Numerical Simulation Of Combustion And Emissions Behavior Of Representative Conventional And Bio-Derived Fuels, Mazen A. Eldeeb

Mineta Transportation Institute

The study addresses two of the main challenges facing combustion modeling for transportation fuels: simultaneous simulation of non-related combustion problems and reducing the computational cost of the modeling process itself. To address the first challenge, researchers determine a characteristic flame time from thermal diffusivity and laminar burning velocity. Researchers examine parametric dependence of flame time and ignition delay time on pressure, temperature and equivalence ratio for methane, based on validated chemical kinetic mechanisms. The study reveals flame time and ignition delay time show similar temperature dependence, flame time has stronger dependence on equivalence ratio and weaker dependence on pressure than …


Advances In Repurposing And Recycling Of Post-Vehicle-Application Lithium-Ion Batteries, Charles R. Standridge, Lindsay Corneal, Nicholas Baine May 2016

Advances In Repurposing And Recycling Of Post-Vehicle-Application Lithium-Ion Batteries, Charles R. Standridge, Lindsay Corneal, Nicholas Baine

Mineta Transportation Institute

Increased electrification of vehicles has increased the use of lithium-ion batteries for energy storage, and raised the issue of what to do with post-vehicle-application batteries. Three possibilities have been identified: 1) remanufacturing for intended reuse in vehicles; 2) repurposing for non-vehicle, stationary storage applications; and 3) recycling, extracting the precious metals, chemicals and other byproducts. Advances in repurposing and recycling are presented, along with a mathematical model that forecasts the manufacturing capacity needed for remanufacturing, repurposing, and recycling. Results obtained by simulating the model show that up to a 25% reduction in the need for new batteries can be achieved …