Engineering Commons^™

Numerical Study Of Cone Penetration In Calcareous Sands: Investigating Cone Tip Resistance Correction Factors For Crushable Soils, Stephanie Michelle Hyder

Dissertations and Theses

The cone penetration test (CPT) is used to characterize the behavior and properties of soils, including the susceptibility to earthquake liquefaction triggering. The cone tip resistance relates to liquefaction susceptibility through relative density, where relative density is closely related to both cone tip resistance and liquefaction susceptibility. Currently, published methods of estimating liquefaction potential (i.e., cyclic resistance ratio) are based on silica sands and do not properly characterize calcareous sands. The measured cone tip resistance in calcareous sands is lower than in silica sands at the same relative density; this difference is generally attributed to the higher compressibility of calcareous …

Uncertainty Quantification Of Live Load Effect In Buried Rc Box Culverts, Mohd Firoj

Dissertations and Theses

Although buried and mostly invisible to the traveling public, bridge-sized culverts (i.e., culverts with span around or longer than 20 ft) account for a large proportion of state-managed bridges. As per Oregon Department of Transportation inventory, there are approximately 35,000 culverts in the state highway system. Among them, 10,862 are in poor conditions and need to be analyzed for load rating purposes. The prediction and understanding of live load effects in culverts are crucial to the design, evaluation, and life-cycle maintenance of culverts. These live load effects include maximum bending moments and shear forces at different critical cross sections.

This …

Probability Distribution Fitting For Censored Data: A Practical Guide For Survival Analysis Of Nbi Data For Concrete Bridge Decks In Oregon, Asmaa Almeshaileh

Dissertations and Theses

Many sophisticated statistical models and analyses have been proposed to analyze datasets derived from the national bridge inventory (NBI). These objectives range from creating an understanding of the factors that drive the deterioration of bridge members to providing agencies with quantitative information for their maintenance and repair decisions. As these models become increasingly sophisticated and difficult to comprehend and implement, practicing engineers and owners are less likely to use them. Often, however, grouping data intuitively, for example, per a select structure type or condition rating and analyzing them using prescriptive statistics such as distribution fitting, does not only lie in …

A Bayesian Network-Based Methodology For Improved Bridge Load Rating And Asset Management, Jeffery Mark Roberts

Dissertations and Theses

From the day a new structure is made available for use, to the day that the structure is no longer able to fulfill an intended purpose, structural safety is a vital interest. Managing a portfolio of structures can be a difficult undertaking for an asset manager, particularly if different types of structures are being maintained. The goal is to manage assets in the most efficient manner which can be influenced by, at a minimum, safety and financial concerns.

A potential tool for an asset manager or owner is the use of Bayesian Networks (BNs). When a BN is used to …

Uncertainty Quantification And Fragility Development Of Deteriorating Rc Bridge Piers, Ayush Bhandari

Dissertations and Theses

Corrosion can reduce structural capacity and increase the risk of bridge damage/failure under extreme events. The impact of corrosion on seismic fragility of bridges has been well studied. However, the methodology used in most existing studies requires detailed information on the structural design and condition of a bridge, which is a major hindrance in conducting seismic risk assessment for a large population of bridges. Furthermore, existing studies do not adequately address the time-dependency of uncertainties associated with fragility curve development. This study presents a methodology to generate time-dependent seismic fragility curves for deteriorating highway bridges based only on the limited …

Seismic Performance Design Criteria Of Existing Bridge Bent Plastic Hinge Region And Rapid Repair Measures Of Earthquake Damaged Bridges Considering Future Resilience, A K M Golam Murtuz

Dissertations and Theses

The main objective of this research was to evaluate the seismic performance of existing sub-standard reinforced concrete (RC) bridge column-spread footing subassemblies and to quantify the material strain limits through a full-scale experimental program. A total of six column-footing test specimens with pre-1990 construction details were subjected to reverse cyclic lateral loading, utilizing a conventional three-cycle symmetric loading protocol and a protocol representing the demands expected from a CSZ earthquake. Additionally, the tests were designed so that variable axial loading could be applied to simulate the secondary load effects experienced during an earthquake in a column that is part of …

Determinant Factors Of Bicyclist Injury Severity At Signalized And Unsignalized Intersections, Apy Das

Dissertations and Theses

Bicycling is becoming increasingly popular in Oregon and the US in general due to its environment friendliness as well as health benefits. With Oregon's population projected to increase by more than 30% over the next 30 years, improving the safety of the transportation network for persons on bicycles is important. In Oregon, majority of the bicyclist crashes occur at intersections. This thesis seeks to identify the determinant factors that significantly impact bicyclist crash injury severity at intersections. A mixed logit framework that accounts for any unobserved heterogeneity in the data and allows the estimated parameters to randomly vary across observations …

Undrained Cyclic Loading Of Low Plasticity Silty Soils In The Pacific Northwest Using Laboratory And Field Cyclic Shear Testing, Angelica Melissa Preciado Reyes

Dissertations and Theses

The cyclic behavior of a fine-grained low plasticity silty soil (plasticity index of approximately 15) at a site in Portland, Oregon, is characterized using a field and laboratory cyclic shear test program. The field cyclic tests were performed using the NHERI@UTexas large mobile shakers T-Rex and Rattler. The laboratory tests were performed using resonant column torsional shear and cyclic direct simple shear devices. This testing program's results were used to evaluate the soil's potential to develop excess pore water pressure with cyclic shear strains ranging from 0.00001% to 3%. The laboratory cyclic test results are compared against field cyclic test …

Kinematic Demands On Pile-Supported Wharves Due To Liquefaction-Induced Lateral Ground Deformations, Thomas John Torkelson Ii

Dissertations and Theses

Kinematic demands from lateral soil deformations can be a major cause of damage to maritime and highway transportation structures such as wharves, ports, and bridges. Data from five centrifuge tests on pile-supported wharves were used to evaluate the accuracy of Newmark Sliding Block Analysis in estimating the kinematic demands on piles. The piles in the centrifuge tests were subjected to varying degrees of liquefaction-induced lateral ground deformations. Pile-pinning effects were included in the analysis by incorporating the lateral pile resistance in the limit-equilibrium slope stability analysis. The results of the analysis have shown that the median Newmark displacements better estimated …

Field Trials And Long-Term Monitoring Of Microbially-Induced Desaturation For The Treatment Of Liquefiable Silty Soils, Kayla Rae Sorenson

Dissertations and Theses

Earthquake liquefaction hazards in silty soils are a critical problem in Portland, Oregon, and other areas around the world. This is a particular problem for existing facilities founded on liquefiable soils, for which there exists no cost-effective liquefaction mitigation solution at the present time. It is essential from both a seismic safety and a seismic resilience perspective to be able to mitigate potentially liquefiable soils underneath existing structures, and to do so in a cost-effective manner. Recent studies suggest that liquefaction mitigation using microbially-induced desaturation (MID) may provide this capability.

The objective of MID is to reduce earthquake-induced excess pore …

Using Quantitative Stereology On High Resolution Sem Images To Estimate Diatom Percentages, Ariadna Covarrubias Ornelas

Dissertations and Theses

Diatoms are single-celled organisms of various shapes and sizes typically found in aquatic environments. When diatoms die, the organic material decomposes, and the outer skeletons (i.e., frustules) settle and accumulate as sedimentary deposits. These soils, called diatomaceous soils, exhibit nontraditional behavior since the diatom particles are typically hollow skeletons composed of amorphous silica with intricately patterned and abrasive surfaces. Recent studies have shown that diatomaceous soils are challenging geomaterials since even a small percentage of diatom particles will notably affect engineering behavior. Furthermore, laboratory studies on diatomaceous soil mixtures have demonstrated that many engineering soil properties depend on the percentage …

Numerical Simulation Of Continuous Cone Penetration And Interpretation Of Cptu Dissipation Tests, Andrew Phillip Eugene Huffman

Dissertations and Theses

The piezocone penetration test (CPTu) is a commonly used method of geotechnical site investigation. The CPTu is especially useful because it provides a nearly continuous data profile of in-situ soil behavior, which can be correlated to useful engineering parameters. However, limitations exist for interpretation of geotechnical properties from CPTu data and for numerical analysis of cone penetration problems. The research presented in this thesis examines interpretation of coefficient of consolidation from CPTu dissipation test data and implementation of an algorithm to advance numerical simulation of cone penetration problems. This thesis presents analysis of CPTu dissipation responses from field-measured and numerically …

Use Of Carbon Fiber Reinforced Polymer (Cfrp) Including Sheets, Rods, And Ropes In Strengthening And Repairing Long Reinforced Concrete Columns, Yasir Matloob Saeed

Dissertations and Theses

The use of FRP materials in strengthening and repairing of reinforced concrete (RC) structures has increased in the past two decades. Recently, FRP materials have become one of the most used materials in rehabilitation engineering. For seismic retrofitting of RC structures, usually the process involves strengthening or repairing the vertical support elements of the buildings or bridges. Several studies focused on the use of FRP materials in strengthening and repairing RC columns. Externally bonded (EB) FRP sheets or laminates and near-surface-mounted (NSM) FRP rods have been used for enhancing the strength and ductility of RC columns. Although glass FRP (GFRP) …

Dynamic Response Of Highway Bridge Superstructures Subjected To Wave Action: Experimental Analysis And Numerical Modeling, Alaa Waleed Hameed

Dissertations and Theses

Bridges are critical lifeline components of the infrastructure network, enabling economies to function under normal conditions and disaster response and recovery missions to take place after extreme events. Therefore, ensuring satisfactory performance increases community resilience and minimizes both human and economic losses. Coastal bridges, which are the focus of this PhD dissertation, are vulnerable to coastal storms. High failure rates of these bridges during two major hurricane events in the mid-2000s have spurred research activities to better understand the wave-induced forces of coastal bridges.

This PhD research represents a continuation effort to build, implement, and introduce new fundamental concepts and …

Robust Maximum Flow Network Interdiction Problem, Darshan Rajesh Chauhan

Dissertations and Theses

In this thesis, a maximum flow-based network interdiction problem considering uncertainties in arc capacities and interdiction resource consumption is solved. The problem consists of two entities with opposing objectives: the goal of the adversary is to maximize the flow of illicit drugs through the network, while the goal of the interdictor is to minimize the maximum flow by completely interdicting arcs given a specified amount of resources. Lack of complete information about the usage patterns of the transportation network by the adversary results in an uncertain estimate of arc capacity and resources required for interdiction by the interdictor. To account …

Concrete Bridge Deck Performance Data And Metrics For The State Of Oregon, Jael Wettach-Glosser

Dissertations and Theses

Bridge decks are a critical element of a bridge that support and distribute vehicle loads to the superstructure. Because of the requirements of this role, bridge decks are exposed to severe conditions that typically lead to structural deficiency in bridges which is both costly and disruptive. Therefore, to keep bridges and highways in good repair, developing optimal preservation decisions for concrete bridge decks is key. In order to develop effective performance monitoring and preservation schedules, the parameters affecting bridge deck deterioration need to be better understood.

With guidance from the literature and Oregon Department of Transportation (ODOT) personnel, two datasets …

Evaluation Of Low And High Frequency Dynamic Response For Condition Assessment Of Reinforced Concrete Structures, Ali Hafiz

Dissertations and Theses

Concrete is widely used for civil infrastructure structures and they experience deterioration and degradation due to aging, increases in the traffic loads, harsher environmental conditions, use of deicing chemicals, etc. Therefore, evaluating the integrity of reinforced concrete structures has become of increasing interest for infrastructure owners and managers. A number of non-destructive testing (NDT) and structural health monitoring (SHM) methods have been developed in recent decades to aid in evaluating structures and provide input for asset management. One family of these methods uses the dynamic response of a structural member: stress waves (high frequency) and structural vibrations (low frequency). Both …

Seismic Behavior Of Screen Grid Core Insulated Concrete Form Walls, Anwer Sabah Mohammed Mohammed

Dissertations and Theses

The use of the insulated concrete form (ICF) walls in residential buildings has increased over the past few decades. Much research has been conducted to evaluate the lateral strength of these walls by applying monotonic and cyclic loadings. In the current study, full-scale shake table experiments were employed to evaluate the in-plane behavior of four screen grid insulated concrete form (SGICF) walls. The first two wall specimens utilized dry fit insulated form blocks made from recycled expanded polystyrene granules that were bonded together with cement. When stacked, the cavities in the blocks formed a grid of cores that are evenly …

An Analytical System For Determining Disciplinary Vocabulary For Data-Driven Learning: An Example From Civil Engineering, Philippa Jean Otto

Dissertations and Theses

Data-driven learning (DDL), an inductive teaching approach in which students learn through corpus interaction, has gained recent traction as way to teach specialized vocabulary in English for Specific Purposes (ESP) classes. There is little research, however, that addresses how to choose specialized vocabulary for teaching with DDL.

This study addressed this gap in research by exploring the potential of a three-part analytical, corpus-based system for determining vocabulary to teach with DDL for a specific context of language use. This system included (1) identifying words that were significantly more frequent in a specialized expert corpus than in a corpus of general …

An Assessment Of Post-Encroachment Times For Bicycle-Vehicle Interactions Observed In The Field, A Driving Simulator, And In Traffic Simulation Models, Ali Razmpa

Dissertations and Theses

Most safety analysis is conducted using crash data. Surrogate safety measures, such as various time-based measures of time-to-collision can be related to crash potential and used to gain insight into the frequency and severity of crashes at a specific location. One of the most common and acknowledged measures is post-encroachment time (PET) which defines the time between vehicles occupying a conflicting space. While commonly used in studies of motor vehicle interactions, studies of PET for bicycle-vehicle interactions are few. In this research, the PET of bicycle-vehicle interactions measured in the field, a driving simulator, and in a micro-simulation are compared. …

Experimental Investigation Of Cfrp Wrapped Square Non-Ductile Reinforced Concrete Columns, Hayder Lateef Al-Khafaji

Dissertations and Theses

The use of fiber-reinforced polymers (FRP) for retrofitting or strengthening deficient concrete columns noticeably increased in the past few decades. Plenty of research has been conducted on the behavior of FRP-strengthened circular concrete columns, but far less research has dealt with non-circular columns. In the current study, the focus was to investigate the behavior of square columns with low to medium grade concrete and low steel reinforcement that were strengthened using carbon fiber reinforced polymer (CFRP) wrap. In the experimental portion of this investigation, twelve short square reinforced concrete columns (5" x 5" in cross section and 12" high) were …

Behavior Of Prestressed Concrete Beams With Cfrp Strands, Yasir Matloob Saeed

Dissertations and Theses

The high cost of repairing reinforced or prestressed concrete structures due to steel corrosion has driven engineers to look for solutions. Much research has been conducted over the last two decades to evaluate the use of Fiber Reinforced Polymers (FRPs) in concrete structures. Structural engineering researchers have been testing FRP to determine their usability instead of steel for strengthening existing reinforced concrete structures, reinforcing new concrete members, and for prestressed concrete applications. The high strength-to-weight ratio of FRP materials, especially Carbon FRP (CFRP), and their non-corrosive nature are probably the most attractive features of FRPs.

In this study, an experimental …

Evaluating The Effects Of A Congestion And Weather Responsive Advisory Variable Speed Limit System In Portland, Oregon, Matthew Blake Downey

Dissertations and Theses

Safety and congestion are ever present and increasingly severe transportation problems in urban areas throughout the nation and world. These phenomena can have wide-ranging consequences relating to safety, the economy, and the environment. Adverse weather conditions represent another significant challenge to safety and mobility on highways. Oregon is not immune from either of these global issues. Oregon Route (OR) 217, to the southwest of the downtown Portland, is one of the worst freeways for congestion in the state and is also subject to the Pacific Northwest's frequently inclement and unpredictable climate. High crash rates, severe recurrent bottlenecks and highly unreliable …

Understanding Travel Modes To Non-Work Destinations: Analysis Of An Establishment Survey In Portland, Oregon, Christopher D. Muhs

Dissertations and Theses

During the past three decades, research in travel behavior has generally proceeded from broad-level, aggregate analysis of mode share--the proportions of walking, bicycling, transit, and vehicle travel occurring in traffic analysis zones, census tracts, neighborhood, or other geographical units--to fine-grained, disaggregate analysis of mode choices and other trip-making attributes at the individual level. One potential issue is whether there are differences in the types of conclusions drawn from results of analyses performed at these different levels, as these results directly inform transportation planning and policy.

This thesis aims in part to confirm whether the types of conclusions drawn from different …

Coupling The Hydrodynamic And Water Quality Model Ce-Qual-W2 With A Multi-Trophic Fish Bio-Energetics Model For Lake Roosevelt, Washington, Michael Lee Mckillip

Dissertations and Theses

Grand Coulee Dam created Franklin D. Roosevelt Lake as part of the Columbia Basin Project. Located in northeastern Washington State, the Project provides economically important hydropower (19 billion kilowatt hours per year), irrigation (225,000 ha), flood control, and sport fishing ($5 to 20 million annually). A good system understanding aids in balancing these beneficial uses for the 230 km long reservoir. The reservoir's atypical 45-day mean residence time is much shorter than a typical lake, and much longer than for a riverine dam. The spring freshet requires drawdowns of 15 to 20 m for flood control—the driving characteristic of reservoir …

Improved Regression-Based Streamflow Forecasting Considering Large-Scale Climate Variability, Austin R. Fisher

Dissertations and Theses

The Natural Resources Conservation Service (NRCS) produces water supply forecasts for most of the streams in the western United States. The NRCS produces forecasts starting in January, when snow course measurements of snow water equivalent were available. Although the seasonal streamflow volume forecasts made by the NRCS are useful, many water supply managers need information at the beginning of the water year in October and would like to see forecasts in the form of a monthly hydrograph.

An investigation into the effect of decadal scale variability, as reflected by the Pacific Decadal Oscillation (PDO), show important relationships that may be …

Modeling Improvements For Water Supply Forecasting In The Columbia River Basin, Daniel Albert Buller

Dissertations and Theses

The purposes of this study were twofold. The first was to explore possible improvements that could be made over existing methods by applying alternative modeling approaches, including the one developed by Garen to forecast runoff volumes in the Columbia River at The Dalles, Oregon. The second was to use the Southern Oscillation as one of the variables to forecast spring and summer runoff and to evaluate whether this variable adds significant information early in the season before any snow has accumulated. The Columbia River basin's mountainous topography and northern latitude are ideally suited for water supply forecasting because much of …

Numerical Simulation Of Contaminated Sediment Transport In The Upper Columbia Slough System, Binghong Wu

Dissertations and Theses

An integrated modeling system has been developed to simulate sediment and contaminated sediment transport in the Upper Columbia Slough System during the Flood of 1996. The modeling system consists of a hydrodynamic model, a sediment transport model, and a contaminant transport model. The hydrodynamic model predicts the Slough flow dynamics and sediment transporting power; the sediment transport model predicts flow-induced sediment transport; and the contaminant transport model predicts the migration of contaminated sediments in the Slough system.

The Upper Columbia Slough modeling system is characterized by its recognition of the complex interplay of Slough hydrology, hydrodynamics, sediment transport, contaminant transport. …

Settlements Due To Arid Collapsible Soils, Heather L. Devine

Dissertations and Theses

The arid alluvial deposits common to the western United States frequently undergo moderate to severe collapse when wetted that can threaten or destroy the stability of structures that are founded on such soils. Additionally, in some areas collapse has been known to occur due to overburden stresses alone. As development expands in these areas a method to estimate the degree of this collapse is essential. Current settlement methods are reviewed and evaluated as they apply to collapsible soils, providing a basis for the development of a proposed settlement method for determining collapse. To aid in the determining the basis for …

A Telescopic Approach To Modeling Leachate Dynamics And Migration At The St. Johns Landfill, Portland, Oregon, Thomas Stephen Lowry

Dissertations and Theses

The St. Johns Landfill is a 225-acre site that lies near the confluence of the Columbia and Willamette Rivers, in the North Portland Industrial District of Portland, Oregon. A slough system surrounds the landfill on three sides with the fourth side adjacent to a shallow lake. The landfill first opened in 1930 when it was operated as an open dump. It operated as an open dump until 1969 when it was converted to a sanitary landfill, employing daily cover and compaction. The landfill was closed in 1991.

The landfill sits directly on top of a thick layer of silty overbank …