Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 4 of 4
Full-Text Articles in Engineering
Impact Of Alumina-Based Binder On Formation Of Dense Strontium Zirconate Ceramics, Janos E. Kanyo, R. Sharon Uwanyuze, Jiyao Zhang, Rainer Hebert, Stefan Schafföner, Lesley Frame
Impact Of Alumina-Based Binder On Formation Of Dense Strontium Zirconate Ceramics, Janos E. Kanyo, R. Sharon Uwanyuze, Jiyao Zhang, Rainer Hebert, Stefan Schafföner, Lesley Frame
Materials Science and Engineering Faculty Research & Creative Works
Strontium zirconate (SrZrO3) is a technical ceramic with potential for refractory applications due to its chemical stability at high temperatures, high melting temperature, and favorable thermal expansion coefficient. Practical use of SrZrO3 is limited by poor mechanical strength relative to ceramics such as alumina (Al2O3). Sintering of SrZrO3 with a hydratable Al2O3 binder is investigated as a method for improving mechanical performance. Density, phase composition, thermomechanical properties, and chemical stability in contact with alloys up to 1350 °C are considered. Results are compared with SrZrO3 samples formed using a traditional polyvinyl alcohol (PVA) binder. SrZrO3 reacts with alumina during sintering …
Methods Of Extrusion On Demand For High Solids Loading Ceramic Paste In Freeform Extrusion Fabrication, Wenbin Li, Amir Ghazanfari, Ming-Chuan Leu, Robert G. Landers
Methods Of Extrusion On Demand For High Solids Loading Ceramic Paste In Freeform Extrusion Fabrication, Wenbin Li, Amir Ghazanfari, Ming-Chuan Leu, Robert G. Landers
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Fabrication of highly dense parts with complex geometry by paste-extrusion-based solid freeform fabrication processes requires a precise control of the extrusion flow rate to dispense material on demand, which is often referred as Extrusion-On-Demand (EOD). The extrusion process for aqueous ceramic pastes is complex and difficult to control due to their non-Newtonian behavior, compressibility and inhomogeneity. In this study, three methods of EOD (based on ram extruder, needle valve, and auger valve) are introduced and investigated for the extrusion of high solids loading (i.e., > 50%, volumetric) aqueous alumina paste. Optimal extrusion process parameters for these methods are determined through printing …
Control Of Fluid Dynamics By Nanoparticles In Laser Melting, Chao Ma, Lianyi Chen, Jiaquan Xu, Jingzhou Zhao, Xiaochun Li
Control Of Fluid Dynamics By Nanoparticles In Laser Melting, Chao Ma, Lianyi Chen, Jiaquan Xu, Jingzhou Zhao, Xiaochun Li
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Effective control of fluid dynamics is of remarkable scientific and practical significance. It is hypothesized that nanoparticles could offer a novel means to control fluid dynamics. In this study, laser melting was used to investigate the feasibility of tuning fluid dynamics by nanoparticles and possibly breaking existing limits of conventional laser processing techniques. Alumina nanoparticles reinforced nickel samples, fabricated through electrocodeposition, were used for laser melting experiments. Since the melt pool surface is controlled by the fluid dynamics, surface topographies were carefully studied to reveal the nanoparticle effect on the fluid dynamics. Characterizations of surface topographies and microstructures of pure …
Experimental Investigation Of Effect Of Environment Temperature On Freeze-Form Extrusion Fabrication, Xiyue Zhao, Michael S. Mason, Tieshu Huang, Ming-Chuan Leu, Robert G. Landers, Greg Hilmas, Samuel J. Easley, Michael W. Hayes
Experimental Investigation Of Effect Of Environment Temperature On Freeze-Form Extrusion Fabrication, Xiyue Zhao, Michael S. Mason, Tieshu Huang, Ming-Chuan Leu, Robert G. Landers, Greg Hilmas, Samuel J. Easley, Michael W. Hayes
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Freeze-form Extrusion Fabrication (FEF) is an additive manufacturing technique that extrudes ceramic loaded aqueous pastes layer by layer below the paste freezing temperature for component fabrication. A computer controlled 3-D gantry system has been developed for the FEF process. The system includes a temperature control subsystem that allows for fabrication of components below the paste freezing temperature. The low temperature environment allows for larger component fabrication. Comparisons in terms of layer thickness, self-sustaining ability, and system response were performed between 0⁰C and -20⁰C for alumina sample fabrications. The minimum deposition angles without use of support material have been determined for …