Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 30 of 36
Full-Text Articles in Engineering
Recovery Of Zinc From The Spent Zinc-Carbon Dry Cell Batteries Through Pyrometallurgical Route, M Haque Khan, Asw Kurny
Recovery Of Zinc From The Spent Zinc-Carbon Dry Cell Batteries Through Pyrometallurgical Route, M Haque Khan, Asw Kurny
Journal of Metals, Materials and Minerals
Spent zinc-carbon batteries of all the five types (AAA, AA, C, D and 9V) were processed to recover zinc metal. All the components of the battery were separated, chemically analyzed and the anodic zinc parts were subjected to pyrometallurgical processing. Extraction of zinc was negligible when no fluxing agent was used. However, extent of recovery increased significantly when chloride salts: sodium chloride, calcium chloride and ammonium chloride were used as a fluxing agent. Among these, ammonium chloride gave the best result as flux. Using 10 %wt. of each flux, extraction of zinc was 90% for ammonium chloride, and around 75% …
4-(N,N-Diethylamino)Benzaldehyde Thiosemicarbazone As Corrosion Inhibitor For 6061 Al - 15 Vol. Pct. Sic(P) Composite And Its Base Alloy, G M. Pinto, J Nayak, A N. Shetty
4-(N,N-Diethylamino)Benzaldehyde Thiosemicarbazone As Corrosion Inhibitor For 6061 Al - 15 Vol. Pct. Sic(P) Composite And Its Base Alloy, G M. Pinto, J Nayak, A N. Shetty
Journal of Metals, Materials and Minerals
The inhibitive action of 4-(N,N-diethylamino)benzaldehyde thiosemicarbazone (DEABT) on the corrosion behavior of 6061 Al -15 vol. pct. SiC(p) composite and its base alloy was studied at different temperatures in sulfuric acid medium containing varying concentrations of it, using Tafel extrapolation and AC impedance spectroscopy (EIS) techniques. Results showed that DEABT was an effective inhibitor, showing inhibition efficiency of 80 % in 0.5 M sulfuric acid. The adsorption of DEABT on both the composite and the base alloy was found to be through physisorption obeying Langmuirs adsorption isotherm.The thermodynamic parameters such as free energy of adsorption and activation parameters were calculated.
Effect Of Vanadium On Subcritical Heat Treatment Behavior Of Hypoeutectic 16 Wt% Cr Cast Iron Containing 2 Wt% Mo, R Junsamoot, S Inthidech, K Sriprateep, P Sricharoenchai, Y Matsubara
Effect Of Vanadium On Subcritical Heat Treatment Behavior Of Hypoeutectic 16 Wt% Cr Cast Iron Containing 2 Wt% Mo, R Junsamoot, S Inthidech, K Sriprateep, P Sricharoenchai, Y Matsubara
Journal of Metals, Materials and Minerals
Subcritical heat treatment of austenite in alloyed cast iron by tempering at the temperature below pearlite transformation (A1), has been used to improve matrix hardness without hardening. Hypoeutectic high chromium cast irons containing 16 wt% Cr - 2 wt% Mo without and with V were prepared in order to clarify the effect of holding temperature and holding time on behavior of hardness and decomposition fraction of austenite in matrix (f) in subcritical heat treatment. As-cast specimens were held at temperature from 723 K to 923 K for 14.4 - 43.2 ks, and then cooled by fan air. In the as-cast …
Highly Porous Silica Network Prepared From Sodium Metasilicate, R E. Essien, O A. Olaniyi, L A. Adams, R O. Shaibu
Highly Porous Silica Network Prepared From Sodium Metasilicate, R E. Essien, O A. Olaniyi, L A. Adams, R O. Shaibu
Journal of Metals, Materials and Minerals
Porous silica network was prepared from sodium metasilicate (Na2SiO3) at room temperature (27C) using hydrochloric acid (HCl) as catalyst through the sol-gel method. The gel was dried at 120C for 1 day and calcined at 800C for 3 hours and the material obtained characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The results showed the formation of amorphous silica particles of average sizes 598 nm with ordered porous network of pore sizes ranging from 0.18-0.91 ?m. This synthetic route uses sodium metasilicate as commercial precursor without pore forming templates which could be useful …
Ni Electroless Plating Of Abs Polymer By Palladium And Tin-Free Process, P Dechasit, W Trakarnpruk
Ni Electroless Plating Of Abs Polymer By Palladium And Tin-Free Process, P Dechasit, W Trakarnpruk
Journal of Metals, Materials and Minerals
A palladium and tin-free process for the Ni electroless plating of acrylonitrile-butadiene-styrene (ABS) polymer has been developed. The ABS was first etched then activated with Ni (or Co) ions. Ni or Co adsorbed was quantified by atomic absorption spectroscopy. Sodium borohydride solution was found to be effective in reduction of Ni (or Co) ions. By immersing in a Ni plating bath the Co (or Ni) can then auto-catalytically deposit a Ni film on the ABS. The amount and thickness of Ni film determined by SEM-EDX were the highest when using 3 g/L of nickel acetate solution, 0.5 M sodium borohydride …
Preparation Of Copper Lead Frame By Powder Metallurgy Technique, P Y. Chew, A H. You, T R. Vijayaram, B K. See, P S. Lim, M C. Ng
Preparation Of Copper Lead Frame By Powder Metallurgy Technique, P Y. Chew, A H. You, T R. Vijayaram, B K. See, P S. Lim, M C. Ng
Journal of Metals, Materials and Minerals
Pure Cu is prepared with the dimension of 17.7 mm in diameter and 10 - 15 mm in height using powder metallurgical method to characterize its electrical and mechanical properties. These samples are compacted at a constant pressure of 280 MPa. Pure Cu pellets are sintered at 600C and 950C for 3, 4 and 7 hours. Before sintering, pure Cu pellet is subjected to SEM in order to check the compactness of the pellet, and also the grain structure of the Cu. All the pellets with different temperatures are re-weighed and sintered density are calculated after sintering. Besides that, porosity …
Mechanical Properties Of Stir-Mixed Sicp-Reinforced Aluminium Composites, R Buntan, D Phuenchomphu, P Sukmoung, K Doomao, O Anunapiwat, T Patcharawit
Mechanical Properties Of Stir-Mixed Sicp-Reinforced Aluminium Composites, R Buntan, D Phuenchomphu, P Sukmoung, K Doomao, O Anunapiwat, T Patcharawit
Journal of Metals, Materials and Minerals
Aluminium composites have found their strength in engineering applications such as automotive, electrical and light-weight applications. To achieve uniform microstructure and good mechanical properties, the fabrication techniques are prime factors in controlling wettability and porosity problems. This research therefore aimed for studying microstructure-mechanical property relation of SiCp-reinforced 356 aluminium composites fabricated by a cost-effective stir casting process, to which three elemental additions, Al-5Ti-B, Sr, and Mg,were investigated. Furthermore, effects of SiCp additions (0-15 wt.%) and T6 heat treatment (530C/12h + 155C/4 h) on mechanical properties of the composites were also studied. The 356 aluminium ingot was melted at 700C then …
Process Parameter-Microstructure-Mechanical Property Relations Of Sicp-Reinforced Aluminum Composites Produced By Powder-Injection Casting, M Bunma, P Subarporn, R Bobuangern, T Patthannkitdamrong, T Thuanwong, T Patcharawit
Process Parameter-Microstructure-Mechanical Property Relations Of Sicp-Reinforced Aluminum Composites Produced By Powder-Injection Casting, M Bunma, P Subarporn, R Bobuangern, T Patthannkitdamrong, T Thuanwong, T Patcharawit
Journal of Metals, Materials and Minerals
Aluminum composites are of interest for engineering applications such as electrical and especially automotive applications and their final physical and mechanical properties are usually determined by fabrication techniques. This research aimed to study effects of process parameters, which are i) argon gas flow rates at 5 and 10 l/min, and ii) casting temperatures at 620 and 680C, on integrity of the SiCp-reinforced 356 aluminum composites fabricated by powder-injection casting using a modified flux injection degassing machine. The SiCp additions are 0, 10 and 15 wt.%. Microstructure - mechanical property relations were constructed based on the predetermined process parameters. Aluminum 356 …
Synthesis Of Aligned Carbon Nanotubes By Floating Catalyst Method Using Ferrocene, R Ravindra, B R. Bhat
Synthesis Of Aligned Carbon Nanotubes By Floating Catalyst Method Using Ferrocene, R Ravindra, B R. Bhat
Journal of Metals, Materials and Minerals
The aligned carbon nanotubes (CNTs) have been synthesised by floating catalyst method using ferrocene as catalyst precursor and acetylene as carbon precursor. The reaction was carried out at 850C in double stage chemical vapor deposition (CVD) apparatus. The grown aligned CNTs were purified by air oxidation and acid treatment method. The aligned CNTs were characterised by using scanning electron microscopy, transmission electron microscopy and Raman spectroscopy. The purity of CNTs was determined by Thermal analysis and X-ray diffraction method. The average diameter of aligned CNTs were around 20nm. This process not only produces aligned CNTs but also avoids the preparation …
Multi-Properties Of Chitosan/Montmorillonite Composite Films Incorporated With Virgin And Modified Montmorillonite, S Kittinaovarat, W Nitayaphat, N Jiratumnukul, S Charuchinda
Multi-Properties Of Chitosan/Montmorillonite Composite Films Incorporated With Virgin And Modified Montmorillonite, S Kittinaovarat, W Nitayaphat, N Jiratumnukul, S Charuchinda
Journal of Metals, Materials and Minerals
Chitosan (CTS) composite films were prepared by blending CTS with virgin or modified montmorillonite (vMMT or mMMT, respectively) and then spin coating. XRD analysis showed a good intercalation of CTS and the mMMT in the depolymerized 15 kDa CTS/mMMT composite. The tensile strength and rigidity of the CTS/vMMT and CTS/mMMT composite films increased, whilst the elongation at break decreased, with increasing levels of vMMT or, especially, mMMT from 0.1 to 2% (w/w). Both types of CTS/MMT composite films displayed a decreased oil and water absorption with increasing levels of incorporated vMMT or mMMT. Some aggregation of vMMT but not mMMT …
Development Of Composition Modulated Multilayer Alloy Coatings And Their Corrosion Behavior, S Yogesha, A C. Hegde
Development Of Composition Modulated Multilayer Alloy Coatings And Their Corrosion Behavior, S Yogesha, A C. Hegde
Journal of Metals, Materials and Minerals
Multilayer Zn-Ni alloy coating was developed on mild steel from acid chloride bath containing thiamine hydrochloride, as additive. Composition modulated multilayer alloy (CMMA) coatings, or simply, multilayer coating with gradual change in composition were developed galvanostatically using triangular current pulses from single bath technique. CMMA coatings of Zn-Ni were developed under different conditions, such as cyclic cathode current densities (CCCDs) and a number of layers, and their corrosion behaviors were evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy method. Optimal configuration, (Zn-Ni)2.0/4.0/600 was found to exhibit ~50 times better corrosion resistance compared to monolayer (Zn-Ni)3.0 alloy, deposited from the same …
Immobilization Of Lipase Onto Cyperus Papyrus L. For Biodiesel Production By Transesterification And Hydrolysis-Esterification, S Charuchinda, P Suthianthong, W Chulalaksananukul
Immobilization Of Lipase Onto Cyperus Papyrus L. For Biodiesel Production By Transesterification And Hydrolysis-Esterification, S Charuchinda, P Suthianthong, W Chulalaksananukul
Journal of Metals, Materials and Minerals
Lipase of Candida rugosa was immobilized on biomass support, plant fiber from Cyperus papyrus L., for biodiesel synthesis. The two immobilization techniques investigated in this study were physical adsorption and covalent binding with 1-Ethyl-3-(3-dimethylaminopropyl)carbodiimide (EDC). Results showed that the prepared immobilized lipase by physical adsorption with adding heptane presented higher protein loading, lipase activity and degree of immobilization than that by physical adsorption in phosphate buffer solution and by covalent binding. This immobilized lipase was further applied as biocatalyst for biodiesel synthesis by transesterification and hydrolysis-esterification. The results showed that this immobilized lipase preferred to hydrolyze triglyceride in palm oil …
Determination Of Forming Limit Stress Diagram For Formability Prediction Of Spce 270 Steel Sheet, S Panich, V Uthaisangsuk, J Juntaratin, S Suranuntchai
Determination Of Forming Limit Stress Diagram For Formability Prediction Of Spce 270 Steel Sheet, S Panich, V Uthaisangsuk, J Juntaratin, S Suranuntchai
Journal of Metals, Materials and Minerals
The aim of this research is to apply numerical Finite Element Method (FEM) for determining Forming Limit Stress Diagram (FLSD) of sheet steel of grade SPCE 270. As a failure criterion for formability prediction in sheet metal forming process, the conventional Forming Limit Diagram (FLD) is often used. The FLD is a strain based criterion, by which the principal strains at failure are evaluated. Many investigations showed that the FLD is dependent on forming history and strain path. However, the stress based criterion does not confirm this dependency. This criterion is more robust against any changes in the strain path …
Effect Of Nitrogen Partial Pressure On Characteristic And Mechanical Properties Of Hard Coating Tialn Film, C Chokwatvikul, S Larpkiattaworn, S Surinphong, C Busabok, P Termsuksawad
Effect Of Nitrogen Partial Pressure On Characteristic And Mechanical Properties Of Hard Coating Tialn Film, C Chokwatvikul, S Larpkiattaworn, S Surinphong, C Busabok, P Termsuksawad
Journal of Metals, Materials and Minerals
(Ti,Al)N coating has been serving for the industry as cutting and forming tools. Compared with TiN film, TiAlN film significantly increases tool lifetime. Therefore, it reduces machine downtime and increases productivity. In this work, (Ti,Al)N film was deposited on cold-work tool steel (SKD 11) using PVD cathodic arc system. The sintered Ti-Al target with composition of (at%) 50 Ti and 50 Al was used as a cathode. The deposition bias voltage, bias arc current and deposition time were set at 100 V, 70 A and 90 minutes, respectively. Nitrogen gas was purged into the system with the applied pressure of …
Corrosion Prevention Of Rebar In Concrete Due To Chloride, Y Srimahajariyaphong, S Niltawach
Corrosion Prevention Of Rebar In Concrete Due To Chloride, Y Srimahajariyaphong, S Niltawach
Journal of Metals, Materials and Minerals
In coastal and brackish areas, black rebar in concrete structures suffers from chloride corrosion which leads to spalling of the concrete. The Half Cell Potential Measurement technique has been applied to study the corrosion behavior of both black and galvanized deformed rebar in different concretes. Additives in the concretes vary from pozzolan, calcium nitrite, to pozzolan plus calcium nitrite. Rebar which has higher half cell potential possesses better corrosion resistance. It has been found that concrete cover thickness has no significant effect on the half cell potential of either rebar; that for both types of rebar, the half cell potential …
Study Conditions Of Aluminum Billets For Relationship Between Precipitated Phases And Homogenizing Temperature With Different Cooling Methods, U Phongsophitanan, M Polboon, N Chumchery
Study Conditions Of Aluminum Billets For Relationship Between Precipitated Phases And Homogenizing Temperature With Different Cooling Methods, U Phongsophitanan, M Polboon, N Chumchery
Journal of Metals, Materials and Minerals
In producing cast aluminum billets for using in extruded profile production, homogenization is one of the significant steps of the process. This project examined a suitable homogenizing temperature for usage in manufacturing besides common condition. Computerized fluid dynamics and image analysis solution were techniques to identify the relationship between the area fraction of precipitated phases and homogenizing temperature with different cooling methods. Temperature gradient pattern revealed that soaking temperatures at 575C and 565C are suitable conditions to be used in manufacturing. Furthermore, area fraction calculation showed that the area fractions of precipitated phases of each cooling method were not significantly …
Chevron Crack Initiation In Mullti-Pass Drawing Of Inclusion Copper Shaped-Wire, S Norasethasopon
Chevron Crack Initiation In Mullti-Pass Drawing Of Inclusion Copper Shaped-Wire, S Norasethasopon
Journal of Metals, Materials and Minerals
In the copper superfine wire drawing, the internal cracks such as chevron cracks and breakage of the wire were fatal to the success of quantitative drawing operations. This paper shows how the main process parameters, the drawing pass numbers, influence the plastic deformation, hydrostatic stress, maximum principal tensile stress and chevron cracks initiation investigated by FEM simulation. The effect of the lateral and longitudinal sizes of a central cylindrical inclusion in the multi-pass copper shaped-wire drawing was studied. The plastic deformation, plastic strain, hydrostatic stress and maximum principal tensile stress of the copper shaped-wire containing an inclusion were obtained from …
The Change Of Surface Alloy Compositions And Corrosion Behavior After Wedm Machining Of Commercially Pure Titanium (Grade 4) And Ti-6al-4v (Grade 5), K Sriprasertying, S Rhaiphu
The Change Of Surface Alloy Compositions And Corrosion Behavior After Wedm Machining Of Commercially Pure Titanium (Grade 4) And Ti-6al-4v (Grade 5), K Sriprasertying, S Rhaiphu
Journal of Metals, Materials and Minerals
Nowadays, titanium and its alloys are widely used in medical applications because of excellent corrosion resistance and a high strength-to-weight ratio. Nevertheless, titanium and its alloys are classified as difficult-to-machine metals by conventional machining methods. Therefore, unconventional machining processes are recommended. Wire-electrical discharge machining (WEDM) has become an important non-traditional machining process, as it provides an effective solution for machining components made from difficult-to-machine metals. However, WEDM could damage the surface layer and have an effect on the biocompatibility properties. This research was focused on the effect of WEDM on grade 4 commercially pure titanium and Ti-6Al-4V (Grade 5) after …
Modification Of Montmorillonite With A Cationic Softener For Finishing Cotton Fabric With Hand Builder Performance, S Kittinaovarat, N Jiratumnukul, N Koolpreechanan
Modification Of Montmorillonite With A Cationic Softener For Finishing Cotton Fabric With Hand Builder Performance, S Kittinaovarat, N Jiratumnukul, N Koolpreechanan
Journal of Metals, Materials and Minerals
Montmorillonite (Mont) was modified by cationic exchange with the cationic softener TEGO 28 (Di-Palm carboxyethyl hydroxyethyl methyl ammonium methosulfate). XRD analysis suggested that intercalation occurred in the modified Mont (mMont). Softening finishing solutions composed of pure TEGO 28 with and without mMont were treated on cotton fabrics by the pad-dry method and then evaluated for stiffness, whiteness, tear strength and thermal stability. TEGO 28 treatment alone increased the stiffness property of the finished fabrics, and this was increased further by the co-inclusion of mMont at 3 and 5% (w/v), but higher or lower mMont concentrations led to a marked and …
Chitosan And Trimethyl Chitosan Particles As Oral Vaccine Delivery Systems: Comparison Of The Potential To Initiate Immune Responses, S Boontha, H Ej Unginger, N Waranuch, A Polnok, T Pitaksuteepong
Chitosan And Trimethyl Chitosan Particles As Oral Vaccine Delivery Systems: Comparison Of The Potential To Initiate Immune Responses, S Boontha, H Ej Unginger, N Waranuch, A Polnok, T Pitaksuteepong
Journal of Metals, Materials and Minerals
In this study, particles having low MW (Chi-L), high MW (Chi-H) and their respective trimethyl chitosan (TMC) with a degree of quaternization (DQ) of about 40% (TMC-L-40 and TMC-H-40), and prepared by using chitosan, were used to compare their potentials for provoking immune responses to ovalbumin (OVA) following oral administration. The results showed that the Chi-L particles gave higher serum immunoglobulin G (IgG) responses to OVA than those induced with Chi-H, TMC-L-40 and TMC-H-40 particles. However, Chi-L and Chi-H particles gave similar secretory immunoglobulin A (sIgA) to OVA, and sIgA titers obtained from mice immunized with OVA-loaded TMC were negligible. …
Purification Of An Industrial Aluminum Alloy By Melt Stirring During Ohno Continuous Casting Process, S Fashu, L Jianguo, H Q. Dan
Purification Of An Industrial Aluminum Alloy By Melt Stirring During Ohno Continuous Casting Process, S Fashu, L Jianguo, H Q. Dan
Journal of Metals, Materials and Minerals
With the purpose of upgrading the purity of a dilute industrial aluminum alloy during Ohno Continuous Casting (OCC) process through the use of forced melt stirring; the critical stirring intensity required under a casting speed of 2 mm/min was numerically determined. The determined critical stirring intensity induces convective velocity magnitudes into the melt which are effective in transporting solutes from the solute boundary layer into the bulk melt. It was found that, with adequate melt stirring, production of substantially long and high purity ingots during OCC is possible before their purity diminishes to lower than the initial alloy purity.
Improving Quench Hardening Of Low Carbon Steel, T Korad, M Polboon, N Chumchery, J Pearce
Improving Quench Hardening Of Low Carbon Steel, T Korad, M Polboon, N Chumchery, J Pearce
Journal of Metals, Materials and Minerals
The carbon content in steel determines whether it can be directly hardened. If the carbon content is low (less than 0.25wt%) then an alternate means exists to increase the carbon content of the surface. In this study, the mixed quenchant consisting of brine and surfactants known as Superquench was applied in the quench-hardening process on AISI 1015 low carbon steel. The quench results were compared with quenching in heavy brine solution, water and oil which are recognized as the basic quenchants and cannot cause bulk-hardening low-carbon steels. The hardness tests on different points along the radius of cut round bar …
Design And Construction Of Water Atomizer For Making Metal Powder, S Yenwiset, T Yenwiset
Design And Construction Of Water Atomizer For Making Metal Powder, S Yenwiset, T Yenwiset
Journal of Metals, Materials and Minerals
Water Atomization for metal powder is an appropriate method for producing metal powder from different kinds of metal. Typically, a water atomizing machine is designed with a molten metal spraying chamber in a vertical or horizontal orientation depending on a nozzle design, a molten metal spraying chamber and related components. The main variables influencing the working condition of the water atomization process, which affect sizes, shapes and distribution of metal powder particles, are water pressure, water flow rate, a temperature higher than melting point of liquid metal and flow rate of liquid metal. The water atomizing machine in the study …
Effect Of Postweld Heat Treatment On Microstructures And Hardness Of Tig Weldment Between P22 And P91 Steels With Inconel 625 Filler Metal, N Tammasophon, W Homhrajai, G Lothongkum
Effect Of Postweld Heat Treatment On Microstructures And Hardness Of Tig Weldment Between P22 And P91 Steels With Inconel 625 Filler Metal, N Tammasophon, W Homhrajai, G Lothongkum
Journal of Metals, Materials and Minerals
This research aims at searching for the optimal postweld heat treatment condition of the TIG weld joint between P22 (2.25Cr) and P91 (9Cr) steels using Inconel 625 as filler metal. The postweld heat treatment at 750C for 2, 4 and 6 hours was applied in order to reach the proper microstructure and hardness for high performance in mechanical properties at elevated temperatures. It is recommended that postweld heat treatment at 750C for 2 hours is the proper condition to reduce the hardness of heat affected zone (HAZ) of P91 steel.
Applying Computer Simulation In Improving Heat Treating Condition Of Thin High-Carbon Steel Parts, T Korad, M Polboon, N Chumchery, J Pearce
Applying Computer Simulation In Improving Heat Treating Condition Of Thin High-Carbon Steel Parts, T Korad, M Polboon, N Chumchery, J Pearce
Journal of Metals, Materials and Minerals
The study was carried out using COSMOSFlowWorks to predict heat treatment conditions for AISI 1085 high-carbon steel sheet that is used to produce automotive parts that require wear resistance and stiffness resulting from controlled moderately high hardness levels. To achieve such properties, flat high-carbon steel parts need to be hardened to produce acicular matrix structures, and the most suitable heat treatment process to harden thin parts without distortion is austempering. In producing hard and stiff thin section parts in this company study the austempering process was performed by soaking at 830C and then quenching in a NaCl salt bath at …
Separation Of Lycopene/Solvent Mixture By Chitosan Membranes, P Yodjun, K Soontarapa, C Eamchotchawalit
Separation Of Lycopene/Solvent Mixture By Chitosan Membranes, P Yodjun, K Soontarapa, C Eamchotchawalit
Journal of Metals, Materials and Minerals
Acetone in view of lower toxicity could be used as extracting solvent of lycopene in tomato paste instead of hexane. The studied chitosan membranes were uncrosslinked and crosslinked types. It was found that the membrane morphology could be changed from porous to dense structure by increasing evaporation temperature or time or by crosslinking. They showed hydrophilicity but not preferred to both acetone and lycopene. The lycopene/acetone mixture could be separated by using water swollen chitosan membrane in pervaporation process. It was found that all studied membranes; i.e., both uncrosslinked and ionically crosslinked membranes prepared at 40 to 60C for 2 …
Self-Crack Closing Ability Of Mortar With Different Additives, D Jaroenratanapirom, R Sahamitmongkol
Self-Crack Closing Ability Of Mortar With Different Additives, D Jaroenratanapirom, R Sahamitmongkol
Journal of Metals, Materials and Minerals
Self-crack closing ability of cementitious materials has been studied in various aspects. However, most studies focus mainly on the cementitious material with only cement as a binder (without mineral additives), although many additives are commonly used at present. This research thus aims to investigate the effect of additives on this self-crack closing ability by observing and measuring crack width on the mortar specimens. Cracks were created on mortar specimens by splitting method at the age of 3 and 28 days. As most reports show that the best self-crack closing performance was achieved when a plenty of water was supplied, the …
ระบบและส่วนประกอบเบื้องต้นของรถไฟฟ้าขนส่งมวลชน, นัทสิทธิ์ นุ่มวงษ์
ระบบและส่วนประกอบเบื้องต้นของรถไฟฟ้าขนส่งมวลชน, นัทสิทธิ์ นุ่มวงษ์
Journal of Transportation and Logistics (TRANSLOG)
No abstract provided.
บทวิเคราะห์เปรียบเทียบกรณีศึกษาสถาบันวิจัยเทคโนโลยีระบบรางในต่างประเทศ (กรณีศึกษาประเทศญี่ปุ่นและเกาหลี), รุ่งโรจน์ กมลเดชเดชา
บทวิเคราะห์เปรียบเทียบกรณีศึกษาสถาบันวิจัยเทคโนโลยีระบบรางในต่างประเทศ (กรณีศึกษาประเทศญี่ปุ่นและเกาหลี), รุ่งโรจน์ กมลเดชเดชา
Journal of Transportation and Logistics (TRANSLOG)
No abstract provided.
บทบรรณาธิการ, ประมวล สุธีจารุวัฒน
บทบรรณาธิการ, ประมวล สุธีจารุวัฒน
Journal of Transportation and Logistics (TRANSLOG)
No abstract provided.