Engineering Commons^™

Lead To Can Abrasion (Ltca) Test, Scott Mangin, Karthik Padmanabhan, Craig Icban

Mechanical Engineering

Pacemakers are medical devices which regulate a person’s heartbeat through electric pulses delivered via an endocardial lead attached to the heart. When a pacemaker is implanted in a patient, there is usually excess length left on the lead. Surgeons will typically wrap the excess lead length around the pacemaker device and close the wound. However, wrapping the lead around the pacemaker outer surface can open the lead to abrasion and cause the lead’s vital electrical insulation to be compromised. This is currently tested using an existing abrasion fixture at Abbott. However, the current tester does not yield consistent data results …

Deep-Sea Water Collector, Chandler Jones, Jenny Verheul, Michael Di Giorgio

Mechanical Engineering

Properties such as nutrients, DNA, pH levels, and primary productivity are difficult to measure onboard an Underwater Remotely Operated Vehicle (UROV) as mobile submarine sensors are highly expensive and conventional water capture devices are too large to be equipped. However, these properties provide an integral view into our oceans, the species that inhabit them, and our influence on the environment. Collected samples of seawater taken back to labs allow researchers to see a clearer picture of ecosystems’ inhabitants and lifecycle with the analysis of Environmental DNA (eDNA) among many other properties. The scope of this project is to design a …

2 Degree Of Freedom Robotic Leg, Oded Tzori, Henry Terrell, Adan Martinez

Mechanical Engineering

Professor Xing, an assistant professor at Cal Poly, proposed the 2 DOF Robotic Leg project for this quarter’s senior project class. The project is to build a robotic leg attached at the hip to a stand, which will be used as a teaching tool and eventually help develop Cal Poly’s very own robotic quadruped. Since this project has multiple uses after its completion, there are multiple customers that it must perform well for: the Cal Poly Mechanical Engineering (ME) Department, the ME Lab instructors, and the students. The Scope of Work (Sections 2 & 3) is composed of 2 main …

Telescope Parallel Actuator Mount: Control And Testing, Samuel S. Artho-Bentz

Master's Theses

This thesis approaches the task of designing a control system for the Parallel Actuator Mount developed by Dr. John Ridgely and Mr. Garrett Gudgel. It aims to create a base framework that directly controls the telescope and can be expanded to accept external command. It incorporates lower priced components and develops more easily approachable software with great functionality. An open-loop method for velocity control is established. Developing repeatable tests is a major focus. Testing finds the control methods developed result in velocity error of less than 5% and position error of less than 1.5% despite several mechanical issues and inaccuracies. …

A Quantitative Approach For Tuning A Mountain Bike Suspension, Steven Robert Waal

Master's Theses

A method for tuning the spring rate and damping rate of a mountain bike suspension based on a data-driven procedure is presented. The design and development of a custom data acquisition system, known as the "MTB DAQ," capable of measuring acceleration data at the front and rear axles of a bike are discussed. These data are input into a model that is used to calculate the vertical acceleration and pitching angular acceleration response of the bike and rider. All geometric and dynamic properties of the bike and rider system are measured and built into the model. The model is tested …

Low-Cost Reaction Wheel Design For Cubesat Applications, Nicholas J. Bonafede Jr.

Master's Theses

As science instruments on CubeSats become more sensitive to the attitude of the spacecraft, better methods must be employed to provide the accuracy needed to complete the planned mission. While systems that provide the accuracy required are available commercially, these solutions are not cost-effective, do not allow the design to be tailored to a specific mission, and most importantly, do not give students hand-on experience with attitude control actuators. This thesis documents the design, modeling, and simulation of a low-cost, student-fabricated, reaction wheel system for use in 3U CubeSat satellites. The entire design process for the development of this reaction …

Electromagnetic Actuator For Camless Engines, Nicholas Olesh, Charlie Thomas Glenwright, Tim Wills De Tone, Darya Daniel Darvish

Mechanical Engineering

This document summarizes the research, objectives, project plan, and design for developing an electromagnetic actuator valve for use in a camless internal combustion engine. While electromagnetic valve actuators have not been implemented into a working product to date, there have been many attempts to research and develop working prototypes. Similar products have been developed, but they do not use purely electromagnetic actuation. This research is significant because it shows the challenge that must be overcome and outlines potential design solutions to the problem. The objectives section highlights the problem statement and what is aimed to be achieved in this project. …

Mug For Tremors, Logan J. Smith, Allen Tecson, Jaret Wedow, Kai Workman

Mechanical Engineering

Melissa Oliver, an occupational therapist at McGuire VA Medical Center, works extensively with veterans who struggle with certain daily activities due to their hand tremors. Hand tremors caused by essential tremor, Parkinson’s Disease, or other physical or neurological impairments can greatly affect an individual’s ability to perform daily tasks. One of these tasks include the ability to handle beverages, as hand tremors can cause excessive sloshing and spilling of liquid. Melissa reached out to find a way to help veterans with hand tremors easily consume liquids. Our team, consisting of Logan Smith, Allen Tecson, Jaret Wedow, and Kai Workman, was …

Surface Autonomous Vehicle For Emergency Rescue, Max Emerick, Ryan Shields, Christopher Feickert, Raymond Impara

Mechanical Engineering

The goal of this document is to clearly define the problem parameters and project objectives and to clearly describe the design process, planned final design, and manufacturing and testing procedures for the senior design project of Team 26: SAVER -- the Surface Autonomous Vehicle for Emergency Rescue. This is both for the purpose of project planning and for clear communication between all parties involved in the project.

The objective of the SAVER project is to develop a proof of concept for an autonomous maritime search and rescue vehicle for aiding in man-overboard missions. To accomplish this goal, a list of …

Optical Filter Selector, Camaryn Chambers, Joel Pitzer, Matthew Allen, Callen Schwefler

Mechanical Engineering

One of the many challenges with launching projectiles into space is predicting how the environment in space will affect the trajectory. One way to do this is to look at optical emissions, also known as airglow, which can only be seen from earth with sensitive equipment. By taking measurements of the light from the airglow, properties about the upper atmosphere can be inferred. This is important because variability in the atmosphere can cause variability in space that can affect astronauts and satellites. In order to accomplish this task, optical filters must be used to observe different bands of wavelengths of …

Sub-Lunar Tap-Yielding Explorer, Styx, Alexander J. Krenitsky, Ryan J. Locatelli, Aaron B. Erickson, Christoopher B. Boone, Westin R. Mchaney

Mechanical Engineering

To diversify the idea pool that NASA has to draw from for future manned and unmanned missions to the Moon and Mars, a design/build competition has been posed to collegiate teams across the country. The challenge is to reach, extract, and purify underground ice reserves in a setting analogous to mars. Along the way, teams will be collecting telemetry to mimic prospecting objectives on the moon.

The Sublunar Tap-Yielding eXplorer, STYX, is the team’s proposed design for the 2020 NASA RASC-AL competition. Some novel design features STYX will use are a rotary tool changer with swappable tools, a sleeve driving …

Pier Portal, Alec W. Hardy

Master's Theses

The Pier Portal marine monitoring system is an internet controlled underwater camera that will enable students, researchers, and the general public the ability to monitor underwater marine life and ocean conditions. Installed at Cal Poly’s Center for Coastal Marine Science pier at Avila Beach, California, the camera can be commanded in real-time to raise or lower to any position between the top of the pier and the bottom of the ocean floor, while providing a live-stream video to the operator and general public. This thesis effort focused on the integration of the various subsystem components through software, and the development …

Cal Poly Supermileage Dynamometer, Jacob Randall, Nate Deffenbaugh, Kyle Milgram

Mechanical Engineering

Our senior project involves designing a chassis dynamometer capable of simulating variable loads for the Cal Poly Supermileage Vehicle (SMV) team. The chassis dynamometer we are developing uses an alternator to develop additional resistance that the vehicle will have to overcome while testing. To implement a control system for the variable load, we use an Arduino Nano paired with multiple sensors and drivers. This control system allows the user to select different levels of resistance that correlate with different road grades. We designed a custom Printed Circuit Board (PCB) that will contain all the electrical components needed for the control …

The Optimum Design Of A Vacuum-Compatible Manipulator To Calibrate Space Based Ultraviolet Imagers, Jason L. Grillo

Master's Theses

Recent discoveries in geospace science have necessitated the design of compact UV imaging instruments to make space-based observations from multiple vantage points. The miniaturized ultraviolet imager (MUVI) instrument from the Space Sciences Laboratory (SSL) at UC Berkeley is under development to facilitate such discoveries on a wider scale. This thesis documents the design, integration, and characterization of a vacuum compatible manipulator to calibrate the MUVI instrument inside the UV thermal vacuum chamber at SSL. Precision linear and rotation stages were implemented with custom mounting plates to achieve four degrees of freedom. Optical components were installed to imitate the MUVI instrument …