Engineering Commons^™

High Temperature Hepa Filter Test Unit Upgrades, Alexander Krippner, Ian Corcorran, Michael Burlando

Mechanical Engineering

No abstract provided.

Sparse Aperture Speckle Interferometry Telescope Active Optics Control System, Matthew Clause

Master's Theses

A conventional large aperture telescope required for binary star research is typically cost prohibitive. A prototype active optics system was created and fitted to a telescope frame using relatively low cost components. The active optics system was capable of tipping, tilting, and elevating the mirrors to align reflected star light. The low cost mirror position actuators have a resolution of 31 nm, repeatable to within 16 nm. This is accurate enough to perform speckle analysis for the visible light spectrum. The mirrors used in testing were not supported with a whiffletree and produced trefoil-like aberrations which made phasing two mirrors …

Modeling And Test Of The Efficiency Of Electronic Speed Controllers For Brushless Dc Motors, Clayton R. Green

Master's Theses

Small electric uninhabited aerial vehicles (UAV) represent a rapidly expanding market requiring optimization in both efficiency and weight; efficiency is critical during cruise or loiter where the vehicle operates at part power for up to 99% of the mission time. Of the four components (battery, motor, propeller, and electronic speed controller (ESC)) of the electric propulsion system used in small UAVs, the ESC has no accepted performance model and almost no published performance data. To collect performance data, instrumentation was developed to measure electrical power in and out of the ESC using the two wattmeter method and current sense resistors; …

A Concept Validation Of A Magnetometry-Based Technology For Detecting Concealed Weapons In Vehicle Door Panels, Nar Vang

Master's Theses

Acts of insurgency have become an increasing threat resulting in extensive measures being taken by the law enforcement authorities to mitigate their devastating effects on human life and infrastructure. This thesis introduces a magnetometry-based information, and signal processing methodology for detecting concealed ferrous objects in vehicle body panels. From extensive literature research, it was observed that while magnetic sensors have been used in a variety of related applications, but they have not been extensively applied to the on-road detection of firearms and explosives concealed in vehicles. This study utilized an extensive experimental protocol for preliminary concept validation. The main idea …

Cookie Dough Portioning Tool, Alex Haughton, Courtney Shipp, Grant Wittenberg

Mechanical Engineering

The Brown Butter Cookie Company (BBCC) is located in Cayucos, California. They sell handmade cookies made without eggs. After a batch is made, dough pieces must be portioned by hand. This process is time consuming, labor intensive, and limits the number of cookies they can make.

Our task was to design a machine to replace or improve this step of the process. After talking with the members of the BBCC and creating a list of specifications for our device, the team has formulated a detailed design of a cookie dough portioning tool for the BBCC. This report includes information on …

Final Design Report For An Automatic Diffraction Grating, Timothy Jung, Edlin Garcia, Kelly Rorden

Mechanical Engineering

The Automatic Diffraction Grating project explored using said technology to measure the angular separation between binary stars. This system would be a dramatic improvement from the current, fixed and manually adjusted diffraction gratings in use, increasing the capability of observatories to conduct autonomous studies of binary systems. Ideally, realizing such a system would be accomplished using a simple design and off the shelf parts, so that the project could easily replicated. The design of this system was approached with a broad look at the possible mechanisms that could be used to effectively construct an Automatic Diffraction Grating, as well as …

Pier2pier: Final Report, Kevin Nelson, Anthony Miller, Paul Maalouf, Chahan Shah

Mechanical Engineering

No abstract provided.

Veloelectric: Creating A Device That Harvests Energy From Bicycles, Austin Hall, Daniel Stohr, Tj Fox

Mechanical Engineering

Long distance mountain bikers, bike-packers, and many bikers in developing countries rely on electrical devices for safety and communication. These specific groups of people operate in areas with little to no electricity, and often times have no power to sustain their devices. The purpose of this Cal Poly senior project, VeloElectric, was to design, build, and test a kinetic energy harvester for bicycles that can be used to charge common mobile devices via USB. This senior project team created a device that attaches directly to a bicycle and uses vibrations to generate energy, which in turn powers a variety of …

Forest Sign Maker, Victor Espinosa Iii, Kevin Ly, Lisa Yip

Mechanical Engineering

Executive Summary:

The Inyo National Forest is arguably one of the most beautiful locations in California, containing natural masterpieces such as Mount Whitney and the Ancient Bristlecone Pine Forest. Despite its magnificence, the Inyo National Forest can be a treacherous region. The Friends of the Inyo take pride in being able to facilitate the viewing experience for all outdoorsmen by maintaining the mountain trails, which includes providing adequate trail signage.

Unfortunately, there is a fundamental issue with the recent state of trail signage in the Inyo National Forest: the rate at which signs are being vandalized or naturally destroyed is …

Tadpole Tandem Electrically Assisted Tricycle, Austin Frederickson, Anthony Jacques, Kris Lawrence, Preston Mcelroy

Mechanical Engineering

The purpose of this senior project was to investigate the possibility of making bikes (as a regular mode of transportation) look much more appealing to the general public. To that end, an electric motor assist system was added to make it easier for the operators of the vehicle. A fairing was added to protect the rider from wind and rain, and an electrical subsystem consisting of a microcontroller and many other components was also added. The electrical subsystem was meant to store the information of different riders, calculate calories burned using a heart beat sensor, and increase visibility using strategically-placed …

Tesseract, Edgar Uribe, Vanessa Faune

Mechanical Engineering

PolySat is a student-run, Cal Poly research program in which students develop small satellites, known as CubeSats, to be sent into space. Since the start of the program in 2000, PolySat has developed eight 10cm x 10cm x10cm CubeSats. Recently, the team has developed two satellites of double, and triple, that size for NASA-KSC & AI-Solutions and the National Science Foundation. The recent volumetric expansion has been driven by high demand for further satellite functionality, which necessitates large power generation capabilities. To remain competitive in the growing CubeSat industry, PolySat must develop a platform that can provide enough power to …

Vibration Table For Environmental Chamber, Michael Czabaranek, Dylan De Caussin

Mechanical Engineering

No abstract provided.

Hydromodus: An Autonomous Underwater Vehicle, Alex Kost, Anu Mahinkanda, Jordan Read

Electrical Engineering

Hydromodus is a student-led multidisciplinary project conceived by Jordan Read designed to provide a low-cost modular hardware and software solution for researchers and scientists. For the scope of the Senior Project class, it is designed to be a baited remote underwater vehicle (BRUV), but the platform is highly modifiable and open-source.

Telepresence: Design, Implementation And Study Of An Hmd-Controlled Avatar With A Mechatronic Approach, Darren Michael Chan

Master's Theses

Telepresence describes technologies that allow users to remotely experience the sensation of being present at an event without being physically present. An avatar exists to represent the user whilst in a remote location and is tasked to collect stimuli from its immediate surroundings to be delivered to the user for consumption. With the advent of recent developments in Virtual Reality technology, viz., head-mounted displays (HMDs), new possibilities have been enabled in the field of Telepresence. The main focus of this thesis is to develop a solution for visual Telepresence, where an HMD is used to control the direction of a …

Evaluation Of Design Tools For The Micro-Ram Air Turbine, Victor Fidel Villa

Master's Theses

The development and evaluation of the design of a Micro-Ram Air Turbine (µRAT), a device being developed to provide power for an autonomous boundary layer measurement system, has been undertaken. The design tools consist of a rotor model and a generator model. The primary focus was on developing and evaluating the generator model for the prediction of generator brake power and output electrical power with and without rectification as a function of shaft speed and electrical load, with only basic manufacturer specifications given as inputs. A series of motored generator evaluation test were conducted at speeds ranging from 9,000 to …

Development Of Electronics, Software, And Graphical User Control Interface For A Wall-Climbing Robot, Lynda Beatriz Tesillo

Master's Theses

The objective for this project is to investigate various electrical and software means of control to support and advance the development of a novel vacuum adhesion system for a wall-climbing robot. The design and implementation of custom electronics and a wirelessly controlled real-time software system used to define and support the functionalities of these electronics is discussed. The testing and evaluation of the overall system performance and the performance of the several different subsystems developed, while working both individually and cooperatively within the system, is also demonstrated.