Engineering Commons^™

Sky Survey Radio Telescope, Jack E. Mcguigan

Electrical Engineering

This document outlines the design of a radio telescope designed to perform hydrogen line sky surveys. The telescope produces radio images mapping the intensity and relative velocities of hydrogen concentrations to their sky coordinates. Over the course of a day, the telescope images the regions of space visible to it, allowing sky survey imagery to be updated daily. Sky survey images are comprised of an array of pixels corresponding to specific sky coordinates. Each 8-bit RGB pixel contains information on the concentrations of hydrogen in the brightness and relative velocity in the color. Radio images mapping the concentrations and velocities …

Power Thyristor Controller For Speed Control Of Dc Motor, Alejandra Zapata, Morgan Erich Boehme, Abdullah Mohammed Awidah, Payton Robert Chalstrom

Electrical Engineering

In this work, a Power Thyristor Controller for Speed Control of DC Motor has been developed with the purpose of replacing an existing simulation experiment, aiming to effectively implement the principle of learning by doing. The primary objective of the experiment setup is to illustrate the fundamental principles and operational mechanisms underlying the firing angle and controlled bridge rectifier. The new experiment is taking advantage of the existing FCRO4100 Single Phase Firing Board that was donated to the University by ENERPRO. The pre-programmed microcontroller is connected to the thyristor bridge rectifier that’s powered by 24VAC. Additionally, a DC motor will …

Flexible Custom Electric Skateboard, Caleb Adam Kelsay

Electrical Engineering

At Cal Poly traveling long distances only accessible by foot such as across campus or from the car park to class can be tiring and time-consuming. While not physically demanding, the trek consumes time in our tight college life schedule. To improve our time efficiency this project provides a relatively lightweight, powered solution to quickly and effectively travel long distances while maintaining full control and safety even on hills, a current limitation of traditional skateboards.

This electric skateboard includes the battery capacity to travel all around campus on a single charge with a compact and flexible skateboard design that provides …

Remote Cable Gantry, Allen L. Bailey

Electrical Engineering

The Remote Cable Gantry is a robotic system that was initially intended to aid in the art of aerial videography. It was designed to enable novice and expert users alike to capture both video footage and audio from perspectives unachievable by current methods. This system uses a series of cables to control the position of a camera gimbal in a defined 3D space and, as a self-contained unit, is portable and easy to use. The Remote Cable Gantry offers a quiet, intuitive, and safe alternative to existing technology, which has been limiting the market and potential of aerial photography and …

Cal Poly Supermileage Electronic Fuel Injection, Alexander Pink

Electrical Engineering

Cal Poly Supermileage is a student-run engineering club that builds prototype gasoline vehicles optimized maximum fuel-efficiency. To power their vehicles, the Supermileage team makes use of single-cylinder, 4-stroke, electronically fuel-injected (EFI) gasoline engines. This report details the development, iterative design & test cycles, and integration of an EFI system for the Supermileage club. This project develops an EFI system that interfaces to the most common types of sensors found in the low-power Supermileage-range of engines, including throttle-position sensors, manifold absolute pressure sensors, gear-tooth hall-effect sensors, variable-reluctance position sensors, engine coolant temperature sensors, intake air temperature sensors, and exhaust oxygen sensors. …

Hydromodus: An Autonomous Underwater Vehicle, Alex Kost, Anu Mahinkanda, Jordan Read

Electrical Engineering

Hydromodus is a student-led multidisciplinary project conceived by Jordan Read designed to provide a low-cost modular hardware and software solution for researchers and scientists. For the scope of the Senior Project class, it is designed to be a baited remote underwater vehicle (BRUV), but the platform is highly modifiable and open-source.

Wind And Hydroelectric Power Simulation For The Dc House Project, Randy Lormand, Christopher Goloskie

Electrical Engineering

This project details the design and integration of a wind and hydroelectric power simulation system in correlation with the DC House Project. The simulator uses variable speed drives to rotate a DC motor which then drives a generator to produce output. This output is then regulated using a DC to DC converter which holds the voltage level constant making it easier to interface with other power sources for the house. The test results indicate that the simulator will be able to produce two separate power outputs that will provide at least 70 Watts of power in the acceptable speed range …

Low Speed Alternator Design, Scott Merrick

Electrical Engineering

No abstract provided.

Micro Hydropower System, Christpher Neally, Ian Verstuyft

Electrical Engineering

The micro hydropower project strives to meet the needs of a specific village in northern Thailand in partnership with Engineers Without Borders. Specifically, the electrical side of the system must be designed to convert the mechanical power of a flowing river that is turning a turbine into sustainable and dependable power. Currently available hydropower systems will be considered, analyzed, and tailored to suit the specific needs of the community in need. The system to be designed will be flexible enough to demonstrate proof-of-concept with the limited maximum generable power in lab while having the ability to be easily scaled for …

Swing Human Powered Generator: For The Dc House Project, Juan Vicente Avelar, Juan Jose Galindo, Juan Pramyr Ramos

Electrical Engineering

The Play Park Human Powered Generator project addresses various ways of generating power. More specifically, this project entails the design and construction of the Swing Power Generator to provide electrical power from mechanical energy. The swing generator will eventually be used as part of the human-powered generators utilized in the DC House project.

A swing generator prototype was built for this project, which demonstrates the feasibility of its use for electrical power source. Detailed design and construction of the swing generator is presented in this report along with results from hardware testing.