Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Institution
- Publication
- Publication Type
Articles 1 - 5 of 5
Full-Text Articles in Engineering
Patterning And Characterization Of Carbon Nanotubes Grown In A Microwave Plasma Enhanced Chemical Vapor Deposition Chamber, Mauricio Kossler
Patterning And Characterization Of Carbon Nanotubes Grown In A Microwave Plasma Enhanced Chemical Vapor Deposition Chamber, Mauricio Kossler
Theses and Dissertations
This research studies the growth of carbon nanotubes (CNT) from a nickel catalyst to be used on a field emission device. This thesis can be divided into three sections: the construction of a vacuum chamber for field emission testing, the design and fabrication of a triode structure to enable improved electron emission, and the pretreatment and growth of CNTs. To experimentally test the field emission of CNTs, a vacuum chamber must attain a vacuum of at least 10-5 torr. Our vacuum chamber designed and built achieved a maximum, final pressure of 10-8 torr. A triode structure was designed …
Material Selection Of Z-Fibre In Stitched Composites - Experimental And Analytical Comparison Approach, Kwek Tze Tan, N. Watanabe, M. Sano, M. Takase, Y. Iwahori, H. Hoshi
Material Selection Of Z-Fibre In Stitched Composites - Experimental And Analytical Comparison Approach, Kwek Tze Tan, N. Watanabe, M. Sano, M. Takase, Y. Iwahori, H. Hoshi
Mechanical Engineering Faculty Research
Strain energy release rates are measured and compared for laminated composites stitched with different fibre materials – Carbon, Kevlar and Vectran. DCB test and FE simulation are performed to evaluate the interlaminar toughness. It is proven that Vectran provides the toughest interlaminar reinforcement and is most suitable for Zfibre application.
Influence Of Shielding Gas On Fume Formation Rate For Gas Metal Arc Welding (Gmaw) Of Plain Carbon Steel, Kristin R. Carpenter, Brian J. Monaghan, John Norrish
Influence Of Shielding Gas On Fume Formation Rate For Gas Metal Arc Welding (Gmaw) Of Plain Carbon Steel, Kristin R. Carpenter, Brian J. Monaghan, John Norrish
Faculty of Engineering - Papers (Archive)
Shielding gas composition is an important parameter for successful gas metal arc welding (GMAW) and has been shown to affect the fume formation rate (FFR). The present paper compares thirteen shielding gases and their impact on FFR in spray transfer. In Ar-based mixtures, increasing CO2 had a greater impact than raising O2 on FFR. When O2 was increased in ternary mixtures, the FFR increased for Ar-5%CO2 but no discernable increase was observed for the Ar-12%CO2 mixtures. Ar-He-CO2 mixtures had the most stable FFR's. The FFR for 100% CO2 was significantly higher due to the change in weld transfer mode to …
Analysis Of Fume Formation Rate And Fume Particle Composition For Gas Metal Arc Welding (Gmaw) Of Plain Carbon Steel Using Different Shielding Gas Compositions, Kristin R. Carpenter, Brian J. Monaghan, John Norrish
Analysis Of Fume Formation Rate And Fume Particle Composition For Gas Metal Arc Welding (Gmaw) Of Plain Carbon Steel Using Different Shielding Gas Compositions, Kristin R. Carpenter, Brian J. Monaghan, John Norrish
Faculty of Engineering - Papers (Archive)
The present paper compares thirteen shielding gases and their impact on FFR and fume particle while welding in the spray transfer regime. There was no obvious influence from the shielding gas on particle composition and fume particles were identified as (Fe,Mn)3O4. There was a slight peak shift that indicated that small levels of Mn, as detected by TEM-EDS, substituted for Fe in the Fe3O4 phase. Shielding gas composition is an important parameter for successful gas metal arc welding (GMAW) and has been shown to affect the fume formation rate (FFR). In Ar-based mixtures, increasing CO2 had a greater impact than …
Carbon Nanotube Network Modified Carbon Fibre Paper For Li Ion Batteries, Jun Chen, Jiazhao Wang, Andrew I. Minett, Yong Liu, Carol M. Lynam, Hua-Kun Liu, G G. Wallace
Carbon Nanotube Network Modified Carbon Fibre Paper For Li Ion Batteries, Jun Chen, Jiazhao Wang, Andrew I. Minett, Yong Liu, Carol M. Lynam, Hua-Kun Liu, G G. Wallace
Faculty of Engineering - Papers (Archive)
Here we report on the direct deposition of large quantities of highly porous carbon nanotube networks onto a carbon fibre paper support; subsequently utilised as the anode in a Li-ion battery application showing improved long-term performance and chemical stability with a significant fully reversible capacity of 546mAh/g.