Open Access. Powered by Scholars. Published by Universities.®
- Discipline
Articles 1 - 10 of 10
Full-Text Articles in Engineering
A Parametric Study For In-Pile Use Of The Thermal Conductivity Needle Probe Using A Transient, Multilayered Analytical Model, Courtney Hollar, Austin Fleming, Kurt Davis, Ralph Budwig, Colby Jensen, David Estrada
A Parametric Study For In-Pile Use Of The Thermal Conductivity Needle Probe Using A Transient, Multilayered Analytical Model, Courtney Hollar, Austin Fleming, Kurt Davis, Ralph Budwig, Colby Jensen, David Estrada
Materials Science and Engineering Faculty Publications and Presentations
By utilizing an in-pile measurement, thermal conductivity can be determined under prototypic conditions over a range of burnup. In this work we develop a multilayer quadrupoles analytical model to describe the transient thermal interactions between a line heat source (i.e. needle probe) and cylindrical nuclear fuel geometry for inpile thermal conductivity measurements. A finite element analysis of the detailed needle probe geometry was compared to results from the analytical model to verify the assumptions made in the analytical model. Experimentally, the needle probe was used to measure the thermal properties of polytetrafluoroethylene (PTFE) and stainless steel 304 with three different …
Simulation Of A Time-Varying Distributed Cathode In A Linear Format Crossed-Field Amplifier, Marcus Pearlman, Jim Browning
Simulation Of A Time-Varying Distributed Cathode In A Linear Format Crossed-Field Amplifier, Marcus Pearlman, Jim Browning
Electrical and Computer Engineering Faculty Publications and Presentations
The effects of a temporally modulated, distributed cathode in a linear format crossed-field amplifier (CFA) are simulated in VSim and analyzed. A linear format, 150 MHz, low power (100 W), moderate gain (7 dB), meander line CFA is used as the basis for the simulation model. This paper describes simulations with different time-varying distributed cathodes in which electron injection is modulated at the RF frequency both in and out of phase with the RF input. At low RF input power the modulated electron injection dominates the operation. Injecting in phase with the RF input shows gain increases from 23 dB …
Work In Progress: Mastery-Based Grading In An Introduction To Circuits Class, Noah Salzman, Kurtis D. Cantley, Gary L. Hunt
Work In Progress: Mastery-Based Grading In An Introduction To Circuits Class, Noah Salzman, Kurtis D. Cantley, Gary L. Hunt
Electrical and Computer Engineering Faculty Publications and Presentations
Circuits is often the first required course in an electrical engineering curriculum that demands application of multiple concepts from prerequisite math and physics courses. This integration of knowledge can be a challenge for many students. Effective teaching methods can enhance the overall learning experience, increase program retention, and improve student understanding of foundational topics in electrical engineering. This paper outlines a mastery-based grading structure implemented in a sophomore-level circuits class. The focus is placed at this level because the course is a critical prerequisite for many other courses in the electrical and computer engineering (ECE) curriculum. The knowledge that students …
Thermal Transport In Layer-By-Layer Assembled Polycrystalline Graphene Films, David Estrada, Alondra Perez
Thermal Transport In Layer-By-Layer Assembled Polycrystalline Graphene Films, David Estrada, Alondra Perez
Materials Science and Engineering Faculty Publications and Presentations
New technologies are emerging which allow us to manipulate and assemble 2-dimensional (2D) building blocks, such as graphene, into synthetic van der Waals (vdW) solids. Assembly of such vdW solids has enabled novel electronic devices and could lead to control over anisotropic thermal properties through tuning of inter-layer coupling and phonon scattering. Here we report the systematic control of heat flow in graphene-based vdW solids assembled in a layer-by-layer (LBL) fashion. In-plane thermal measurements (between 100 K and 400 K) reveal substrate and grain boundary scattering limit thermal transport in vdW solids composed of one to four transferred layers of …
Corrosion Initiation And Propagation On Carburized Martensitic Stainless Steel Surfaces Studied Via Advanced Scanning Probe Microscopy, Armen Kvryan, Corey M. Efaw, Kari A. Higginbotham, Olivia O. Maryon, Paul H. Davis, Elton Graugnard, Michael F. Hurley
Corrosion Initiation And Propagation On Carburized Martensitic Stainless Steel Surfaces Studied Via Advanced Scanning Probe Microscopy, Armen Kvryan, Corey M. Efaw, Kari A. Higginbotham, Olivia O. Maryon, Paul H. Davis, Elton Graugnard, Michael F. Hurley
Materials Science and Engineering Faculty Publications and Presentations
Historically, high carbon steels have been used in mechanical applications because their high surface hardness contributes to excellent wear performance. However, in aggressive environments, current bearing steels exhibit insufficient corrosion resistance. Martensitic stainless steels are attractive for bearing applications due to their high corrosion resistance and ability to be surface hardened via carburizing heat treatments. Here three different carburizing heat treatments were applied to UNS S42670: a high-temperature temper (HTT), a low-temperature temper (LTT), and carbo-nitriding (CN). Magnetic force microscopy showed differences in magnetic domains between the matrix and carbides, while scanning Kelvin probe force microscopy (SKPFM) revealed a 90–200 …
Open-Source Automated Chemical Vapor Deposition System For The Production Of Two-Dimensional Nanomaterials, Lizandra Williams-Godwin, Dale Brown, Richard Livingston, Tyler Webb, Lynn Karriem, Elton Graugnard, David Estrada
Open-Source Automated Chemical Vapor Deposition System For The Production Of Two-Dimensional Nanomaterials, Lizandra Williams-Godwin, Dale Brown, Richard Livingston, Tyler Webb, Lynn Karriem, Elton Graugnard, David Estrada
Materials Science and Engineering Faculty Publications and Presentations
The study of two- dimensional (2D) materials is a rapidly growing area within nanomaterials research. However, the high equipment costs, which include the processing systems necessary for creating these materials, can be a barrier to entry for some researchers interested in studying these novel materials. Such process systems include those used for chemical vapor deposition, a preferred method for making these materials. To address this challenge, this article presents the first open-source design for an automated chemical vapor deposition system that can be built for less than a third of the cost for a comparable commercial system. The materials and …
Toward Improving Ambient Volta Potential Measurements With Skpfm For Corrosion Studies, Corey M. Efaw, Thiago Da Silva, Paul H. Davis, Lan Li, Elton Graugnard, Michael F. Hurley
Toward Improving Ambient Volta Potential Measurements With Skpfm For Corrosion Studies, Corey M. Efaw, Thiago Da Silva, Paul H. Davis, Lan Li, Elton Graugnard, Michael F. Hurley
Materials Science and Engineering Faculty Publications and Presentations
Scanning Kelvin probe force microscopy (SKPFM) is used in corrosion studies to quantify the relative nobility of different microstructural features present within complex metallic systems and thereby elucidate possible corrosion initiation sites. However, Volta potential differences (VPDs) measured via SKPFM in the literature for metal alloys exhibit large variability, making interpretation and application for corrosion studies difficult. We have developed an improved method for referencing SKPFM VPDs by quantifying the closely related work function of the probe relative to an inert gold standard whose modified work function is calculated via density functional theory (DFT). By measuring and tracking changes in …
A Spatiotemporal Pattern Detector, Robert Ivans, Kurtis D. Cantley
A Spatiotemporal Pattern Detector, Robert Ivans, Kurtis D. Cantley
Electrical and Computer Engineering Faculty Publications and Presentations
A spatiotemporal pattern detector design is presented which can identify three fundamental spatiotemporal patterns consisting of two spikes (from different neurons or from the same neuron). These fundamental cases provide the building blocks for construction of more complicated arbitrary spatiotemporal patterns. The overall design consists of three primary subcircuits, and the operation of each is described. The detection of the three cases of spatiotemporal patterns, and the detection of a more complicated pattern by a network of Spatiotemporal Pattern Detectors, is then demonstrated through simulation using the Cadence Virtuoso platform.
Learning Behavior Of Memristor-Based Neuromorphic Circuits In The Presence Of Radiation, Sumedha Gandharava Dahl, Robert C. Ivans, Kurtis D. Cantley
Learning Behavior Of Memristor-Based Neuromorphic Circuits In The Presence Of Radiation, Sumedha Gandharava Dahl, Robert C. Ivans, Kurtis D. Cantley
Electrical and Computer Engineering Faculty Publications and Presentations
In this paper, a feed-forward spiking neural network with memristive synapses is designed to learn a spatio-temporal pattern representing the 25-pixel character ‘B’ by separating correlated and uncorrelated afferents. The network uses spike-timing-dependent plasticity (STDP) learning behavior, which is implemented using biphasic neuron spikes. A TiO2 memristor non-linear drift model is used to simulate synaptic behavior in the neuromorphic circuit. The network uses a many-to-one topology with 25 pre-synaptic neurons (afferent) each connected to a memristive synapse and one post-synaptic neuron. The memristor model is modified to include the experimentally observed effect of state-altering radiation. During the learning process, …
Recovery Of Stem Cell Proliferation By Low Intensity Vibration Under Simulated Microgravity Requires Linc Complex, H. Touchstone, R. Bryd, S. Loisate, M. Thompson, X. Pu, R. Beard, J. T. Oxford, G. Uzer
Recovery Of Stem Cell Proliferation By Low Intensity Vibration Under Simulated Microgravity Requires Linc Complex, H. Touchstone, R. Bryd, S. Loisate, M. Thompson, X. Pu, R. Beard, J. T. Oxford, G. Uzer
Mechanical and Biomedical Engineering Faculty Publications and Presentations
Mesenchymal stem cells (MSC) rely on their ability to integrate physical and spatial signals at load bearing sites to replace and renew musculoskeletal tissues. Designed to mimic unloading experienced during spaceflight, preclinical unloading and simulated microgravity models show that alteration of gravitational loading limits proliferative activity of stem cells. Emerging evidence indicates that this loss of proliferation may be linked to loss of cellular cytoskeleton and contractility. Low intensity vibration (LIV) is an exercise mimetic that promotes proliferation and differentiation of MSCs by enhancing cell structure. Here, we asked whether application of LIV could restore the reduced proliferative capacity seen …