Engineering Commons^™

Studies On Microscopic Flow Structure Inside A Rectangular Circulating Fluidized Bed Through Image Analysis, Jingsi Yang

Electronic Thesis and Dissertation Repository

The microscopic flow structure is studied systematically and comprehensively through a visualization system in a narrow rectangular circulating fluidized bed (CFB) transparent Plexiglas riser with a height of 7.6 m and a cross section of 19 mm × 114 mm. A visualization system consisting of a high-speed video camera, a light source, and image processing and analyzing programs is designed and developed to enable the flow structure to be visualized directly and studied quantitatively. FCC particles of 67 μm are used as the bed materials under different operating conditions with superficial gas velocity (U_g) and solids circulation rate …

Membrane And Performance Study In Polymer Electrolyte Membrane Fuel Cells And Hydrogen Bromine Redox Flow Batteries, Yujia Bai

Doctoral Dissertations

This dissertation represents the consideration of the problems of polymer electrolyte membrane fuel cells (PEMFC) and hydrogen-bromine redox flow batteries (RFB). Due to the importance of water management in PEMFCs, all the experiments were strictly controlled at different water hydration conditions. Water uptake and densities were measured for Nafion^® and a series of 3M ionomer membranes. The thermodynamics of water and polymer was analyzed based on water uptake experiment and calorimetry. Furthermore, partial molar volumes (PMV) of water/membrane system was defined for the first time and used to analyze the interaction between water and polymers. Three states of water …

Optimizing The Sterilization Process Of Canned Food Using Temperature Distribution Studies, Ibrahim M. Ismail, Alaa Fahmy, Ahmed Azab, Magdy Abadir, Seif-Eddeen K. Fateen

Seif-Eddeen K Fateen

The thermal processing of canned food is the most important step in the canning procedure. Retort operating procedures must ensure that uniform processing temperature is achieved and maintained throughout the locations of the canned containers during the process. In this study, temperature distribution tests have been used as a means of verifying the temperature uniformity around the containers. These studies were carried out in two Egyptian canning plants in horizontal water-immersion and water-spray retorts under fully loaded operating conditions. Time-temperature data gathered were used as a guidance tool in improving temperature distribution and in optimizing the process schedule.

Characterization Techniques And Electrolyte Separator Performance Investigation For All Vanadium Redox Flow Battery, Zhijiang Tang

Doctoral Dissertations

The all-vanadium redox flow battery (VRFB) is an excellent prospect for large scale energy storage in an electricity grid level application. High battery performance has lately been achieved by using a novel cell configuration with advanced materials. However, more work is still required to better understand the reaction kinetics and transport behaviors in the battery to guide battery system optimization and new battery material development. The first part of my work is the characterization of the battery systems with flow-through or flow-by cell configurations. The configuration difference between two cell structures exhibit significantly different polarization behavior. The battery output can …

A Generalized Design For Affinity Chromatography Columns, Lee-Wei Kao, Nien-Hwa Linda Wang

The Summer Undergraduate Research Fellowship (SURF) Symposium

In affinity chromatography, an adsorbent with a high selectivity for a target solute is used to isolate the target molecule from other impurities. With sufficient selectivity, the target molecule can be isolated in a highly purified and concentrated state. Common applications of affinity chromatography include Protein A chromatography for antibody purification and Immobilized Metal Affinity Chromatography (IMAC) for protein purification. The well-known design method based on constant-pattern mass transfer zone analysis does not apply to small feed batches, which are insufficient to form constant-pattern frontal waves. Other literature design methods rely on simulation or experimental trials that can be time-consuming …

Development And Applications Of A Novel Intermittent Solids Feeder For Pyrolysis Reactors, Federico M. Berruti

Electronic Thesis and Dissertation Repository

This PhD research addresses the challenge of feeding biomass residues into fluidized bed reactors for pyrolysis, through the development of a novel intermittent solid slug feeder, both for laboratory-scale and large-scale reactors. The new feeder can successfully handle biomass residues that are either too cohesive or thermally sensitive for traditional feeders.

To optimize the novel feeder performance, a model for the pulsating solids flow was developed from experimental data collected with ideal slugs, as well as real biomass flow. The model was validated using both a laboratory-scale (< 10 kg/hr) and large-scale feeder (> 250 kg/hr). Several important variables were identified. They include the material flow …

Pharmaceutical Process Modeling, Optimization, And Control, Ehsan Sheikholeslamzadeh

Electronic Thesis and Dissertation Repository

In this project, the aim was to achieve two important objectives and solve some challenges that the pharmaceutical industry is facing. It will be shown that the NRTL-SAC (Non-random Two Liquid Segment Activity Coefficient) model can best predict the solubility of different pharmaceutical and chemical components in pure and mixed solvents by comparing the results with the well-known model of the UNIFAC. The four parameters that are used in the NRTL-SAC model will be found through nonlinear parameter estimation technique. This project also covers the VLE, LLE, and VLLE phase behaviour calculations using the mentioned models to verify their applicability …

Numerical Modeling Of Solidification Process And Prediction Of Mechanical Properties In Magnesium Alloys, Mehdi Farrokhnejad

Electronic Thesis and Dissertation Repository

A formulation used to simulate the solidification process of magnesium alloys is developed based upon the volume averaged finite volume method on unstructured collocated grids. To derive equations, a non-zero volume fraction gradient has been considered and resulting additional terms are well reasoned. For discretization the most modern approximations for gradient and hessians are used and novelties outlined. Structure-properties correlations are incorporated into the in-house code and the proposed formulation is tested for a wedge-shaped magnesium alloy casting. While the results of this study show a good agreement with the experimental data, it was concluded that a better understanding of …

High Density Gas-Solids Circulating Fluidized Bed Riser And Downer Reactors, Chengxiu Wang

Electronic Thesis and Dissertation Repository

A systematic and comprehensive study of hydrodynamics and reactor performance was conducted in a 76 mm i.d., 10 m high riser and a 76 mm i.d., 5.8 m high downer reactor under high density/flux operating conditions using fluid catalytic cracking (FCC) catalyst particles. An optical fiber probe was used to obtain a complete mapping of local solids holdup and particle velocity. Catalytic ozone decomposition reaction was employed to study the characteristics of reactor performance in the CFB riser and downer. The superficial gas velocity (U_g) and the solids circulation rate (G_s) were 3-9 m/s …

Octanol/Water Partitioning Coefficients Of Pcb Mixtures For Environmental Fate And Transport, Phylicia Cicilio

Honors Theses and Capstones

Polychlorinated biphenyls (PCBs) are a human and environmental toxin introduced to the environment from the 1920’s to the 1970’s from manufacturing items such as transformers and capacitors. PCBs remain in the environment today due to their low water solubility and resistance to chemical reaction. Due to their properties PCBs bioaccumulate in the environment and pose health risks to animals and humans, as they are deemed a probable carcinogen by the EPA. Octanol-water partitioning coefficients are a means of measuring how PCBs will travel in the environment, either partitioning to water or into organic carbon. Octanol-water partitioning coefficients will be determined …

Measurements Of Nh3 Linestrengths And Collisional Broadening Coefficients In N2, O2, Co2, And H2o Near 1103.46 Cm−1, Kyle Owen, Et-Touhami Es-Sebbar, Aamir Farooq

Dr. Et-touhami Es-sebbar

Laser-based ammonia gas sensors have useful applications in many fields including combustion, atmospheric monitoring, and medical diagnostics. Calibration-free trace gas sensors require the spectroscopic parameters including linestrengths and collisional broadening coefficients to be known. Ammonia's strong ν2 vibrational band between View the MathML source has the high absorption strength needed for sensing small concentrations. Within this band, the 1103.46 cm−1 feature is one of the strongest and has minimal interference from CO2 and H2O. However, the six rotational transitions that make up this feature have not been studied previously with absorption spectroscopy due to their small line spacing ranging from …

Effects Of N2o And O2 Addition To Nitrogen Townsend Dielectric Barrier Discharges At Atmospheric Pressure On The Absolute Ground-State Atomic Nitrogen Density, Et. Es-Sebbar, N. Gherardi, F. Massines

Dr. Et-touhami Es-sebbar

Absolute ground-state density of nitrogen atoms N (2p3 4S3/2) in non-equilibrium Townsend dielectric barrier discharges (TDBDs) at atmospheric pressure sustained in N2/N2O and N2/O2 gas mixtures has been measured using Two-photon absorption laser-induced fluorescence (TALIF) spectroscopy. The quantitative measurements have been obtained by TALIF calibration using krypton as a reference gas. We previously reported that the maximum of N (2p3 4S3/2) atom density is around 3 × 1014 cm−3 in pure nitrogen TDBD, and that this maximum depends strongly on the mean energy dissipated in the gas. In the two gas mixtures studied here, results show that the absolute N …

Background And Available Potential Energy In Numerical Simulations Of A Boussinesq Fluid, Shreyas S. Panse

Masters Theses 1911 - February 2014

In flows with stable density stratification, a portion of the gravitational potential energy is available for conversion to kinetic energy. The remainder is not and is called “background potential energy”. The partition of potential energy is analogous to the classical division of energy due to motion into its kinetic and internal components. Computing background and available potential energies is important for understanding stratified flows. In many numerical simulations, though, the Boussinesq approximations to the Navier-Stokes equations are employed. These approximations are not consistent with conservation of energy. In this thesis we re-derive the governing equations for a buoyancy driven fluid …

Performance Evaluation On Vanadium Transport Through Supported Liquid Membrane By Tomac As Carrier, Somayyeh Nosrati Dr, N S. Jayakumar Dr, Mohd Ali Hashim Dr, Soumyadeep Mukhopadhyay Dr

Soumyadeep Mukhopadhyay Dr

Many industries use vanadium increasingly and as a consequence, the toxic effluents cause environmental concern. Here, we study the extraction of vanadium in supported ionic liquid membrane was studied. The effect of operational conditions on the process performance such as initial feed phase concentration, pH of the feed solution, pore size of the membrane support, type of ionic liquid charged on the support and stripping agent solution was investigated. Vanadium was effectively transported from the feed phase to the stripping phase of ammonia solution using the room temperature ionic liquid, tri-n-octyl methyl ammonium chloride (TOMAC) embedded in the support membrane. …

Semi-Empirical Correlation For Binary Interaction Parameters Of The Peng-Robinson Equation Of State With The Van-Der-Waals Mixing Rules For The Prediction Of High-Pressure Vapor-Liquid Equilibrium, Seif-Eddeen K. Fateen, Menna Khalil, Ahmed O. Elnabawy

Seif-Eddeen K Fateen

Peng-Robinson Equation of State is widely used with the classical van der Waals mixing rules to predict vapor liquid equilibria for system containing hydrocarbons and related compounds. This model requires good values of the binary interaction parameter kij. In this work, we developed a semi-empirical correlation for kij partly based on the Huron-Vidal mixing rules. We obtained values for the adjustable parameters of the developed formula for over sixty binary systems and over ten categories of components. The predictions of the new equation system were slightly better than the constant-kij model in most cases, except for ten systems whose predictions …

Mechaniczny Rozdział Faz Proj., Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Challenges And Prospects Of Processes Utilising Carbonic Anhydrase For Co2 Separation, Patrycja Szeligiewicz, Wojciech M. Budzianowski

Wojciech Budzianowski

This article provides an analysis of processes for separation CO2 by using carbonic anhydrase enzyme with particular emphasis on reactive-membrane solutions. Three available processes are characterised. Main challenges and prospects are given. It is found that in view of numerous challenges practical applications of these processes will be difficult in near future. Further research is therefore needed for improving existing processes through finding methods for eliminating their main drawbacks such as short lifetime of carbonic anhydrase or low resistance of reactive membrane systems to impurities contained in flue gases from power plants.

Froth Flotation Performance Enhancement By Feed Cavitation And Magnetic Plastic Particle Addition, Mehmet Saracoglu

Theses and Dissertations--Mining Engineering

Froth flotation is the most commonly used process to recover and upgrade the portion of the coal preparation plant feed that has a particle size smaller than 150 microns. Problems that occur when employing froth flotation in the coal industry include i) coal surfaces that are weakly-to-moderately hydrophobic, and ii) flotation systems that are overloaded and limited by insufficient retention time.

Research was performed to evaluate techniques that could be implemented to improve flotation performance under the aforementioned scenarios. Pre-aeration of flotation feed using a cavitation system was extensively evaluated in laboratory and full-scale test programs. The benefits of adding …

The Critical Role Of Mechanism-Based Models For Understanding And Predicting Liposomal Drug Loading, Binding And Release Kinetics, Sweta Modi

Theses and Dissertations--Pharmacy

Liposomal delivery systems hold considerable promise for improvement of cancer therapy provided that critical formulation design criteria can be met. The main objective of the current project was to enable quality by design in the formulation of liposomal delivery systems by developing comprehensive, mechanism-based mathematical models of drug loading, binding and release kinetics that take into account not only the therapeutic requirement but the physicochemical properties of the drug, the bilayer membrane, and the intraliposomal microenvironment.

Membrane binding of the drug affects both drug loading and release from liposomes. The influence of bilayer composition and phase structure on the partitioning …

Sustainable Operations For Distillation Columns, Yasar Demirel

YASAR DEMIREL

Distillation process consumes about 40% of the total energy used to operate the plants in petrochemical and chemical process industries in North America. Therefore, sustainable distillation column operation requires responsible use of energy and reduction of harmful emission such as CO2. The Aspen Plus ‘Column Targeting Tool’ (CTT) options in a simulation environment can help reduce the use of energy and hence CO2 emission. The Aspen plus ‘Carbon Tracking’ (CT) together with the ‘Global Warming Potential’ options can quantify the reduction in CO2 emission. The CTT is based on the practical near-minimum thermodynamic condition approximation and exploits the capabilities for …

Determination Of Kinetic Parameters From The Thermogravimetric Data Set Of Biomass Samples, Karol Postawa, Wojciech M. Budzianowski

Wojciech Budzianowski

This article describes methods of the determination of kinetic parameters from the thermogravimetric data set of biomass samples. It presents the methodology of the research, description of the needed equipment, and the method of analysis of thermogravimetric data. It describes both methodology of obtaining quantitative data such as kinetic parameters as well as of obtaining qualitative data like the composition of biomass. The study is focused mainly on plant biomass because it is easy in harvesting and preparation. Methodology is shown on the sample containing corn stover which is subsequently pyrolysed. The investigated sample show the kinetic of first order …

Temperature-Dependent Absorption Cross-Section Measurements Of 1-Butene (1-C4h8) In Vuv And Ir, Et-Touhami Es-Sebbar, Yves Benilan, Aamir Farooq

Dr. Et-touhami Es-sebbar

Vacuum ultraviolet (VUV) and infrared (IR) absorption cross-section measurements of 1-butene (1-C4H8; CH2=CHCH2CH3; Butylene) are reported over the temperature range of 296–529 K. The VUV measurements are performed between 115 and 205 nm using synchrotron radiation as a tunable VUV light source. Fourier Transform Infrared (FTIR) spectroscopy is employed to measure absorption cross-section and band strengths in the IR region between 1.54 and 25 μm (∼6500–400 cm−1). The measured room-temperature VUV and IR absorption cross-sections are compared with available literature data and are found to be in good agreement. The oscillator strength for the electronic transition (A1A′→X1A′) around 150–205 nm …