Engineering Commons^™

Effect Of Radiation On Bond Behavior Between Concrete And Steel Bar: Development Of Experimental Protocol, Mohammed Abdelrahman

Masters Theses

There is a need to assess the effect of radiation on the behavior of bond strength between steel reinforcement and concrete. However, there is geometrical constraints in the cylindrical capsule which limit the size of concrete samples. Thus, developing a protocol to produce pullout sample and a test setup is needed.

A protocol for fabricating high-precision concrete samples with embedded \#2 steel bar has been developed based on the results of an experimental program. A pullout system has also been developed to investigate the bond activity of concrete and steel. This research looks at two different aggregate sizes 3/8 inch …

Performance Of Concrete Tunnel Systems Subject To Fault Displacement, Michael Morano

Masters Theses

A Finite Element Analysis (FEA) investigation of concrete tunnel systems traversing seismic faults is carried out to determine how to effectively mitigate the stresses induced in the liner when subject to fault displacement. A parametric study of various fault parameters, both in the damage zone and competent rock, is carried out to determine the site conditions which induce the most stress on the tunnel liner system. Results indicate that friction angle, cohesion, and elastic modulus of fault zones have varying effects on the stresses induced on the liner. The width of damage zone and expected displacements are also investigated and …

Development Of High Early-Strength Concrete For Accelerated Bridge Construction Closure Pour Connections, Stephanie Castine

Masters Theses

Accelerated bridge construction (ABC) has become a popular alternative to using traditional construction techniques in new bridge construction and existing bridge deck replacement because of the reduction of time spent in field activities. A key feature of bridges built using ABC techniques is the extensive use of prefabricated components. Prefabricated components are joined in the field using small volume closure pours involving high performance materials (steel and concrete) to ensure adequate transfer of forces between components. To date, the materials developed for closure pours have been based on proprietary components, so a need has arisen for development of mixes that …

Bridge Deck Research At The University Of Tennessee: A Summary Thesis, Lindsey Brooke Phelps

Masters Theses

Currently, there has been no compilation of all the research the University of Tennessee has completed on chloride ion penetration in concrete bridge decks. The following thesis is a brief summary of the work that has been completed under Dr. Edwin Burdette’s direction over the last six years along with some additional literature review. The testing consisted of Surface Resistivity and Rapid Chloride Ion Penetration testing. This testing showed that there is, in fact a correlation between the two test methods, though SR testing is much easier to conduct. Considerable testing was completed on bridge decks throughout the state of …

Bonded Anchors In Concrete Under Sustained Loading, Douglas Droesch

Masters Theses

Post installed anchors come in either mechanical anchors that develop their strength purely through mechanical interlock with the base concrete, or bonded anchors that develop their strength by bonding anchor rod to the base concrete. Bonded anchors are either grouted, typically cementitious material, or adhesive, typically a chemical material. This thesis presents a current literature review of post-installed bonded anchors, preliminary testing of adhesive bonded anchors, and details of short term and long term test setups for future testing. The purpose of this thesis was to develop the test setups that will be used for future testing on anchors.

Design And Construction Of A Full-Scale Lateral Impact Testing Facility, Cody Aaron Mitchell

Masters Theses

The goal of this work is to design and construct a full scale lateral impact testing facility that is capable of recreating the damage that would be created by an overheight vehicle collision. This was accomplished by impacting a test specimen with an 8000 lbs. impact cart. The impact cart is raised on an elevated track and allowed to roll down the track with a change in height of 10 ft. This change in height is what provides the impact force necessary to recreate an overheight vehicle collision. The track is constructed out of wood and is designed to withstand …

Comparison Of Two Methods For The Assessment Of Chloride Ion Penetration In Concrete: A Field Study, Eric William Ryan

Masters Theses

The currently accepted method for assessing the resistance of concrete to penetration of chloride ions is ASTM C1202, commonly known as the “Rapid Chloride Permeability (RCP) Test.” The test is time-consuming, laborious, has rather high variability, and, is to a degree, user sensitive, making it problematic for inclusion in a performance-based specification. A potential alternative to the RCP test is the “Surface Resistivity (SR) Test”, a method which is dramatically easier, faster, and has less variability than the RCP test. The research reported herein was directed toward determining a correlation between RCP and SR test measurements for Tennessee bridge deck …