Engineering Commons^™

Fatigue Performance Of Flexural Retrofits For Precast Slab Bridges, Ian Stewart

All Theses

This thesis discusses flexural and cyclic load testing of two potential retrofits for pre-cast slab bridges. These slabs came from South Carolina Department of Transportation (SCDOT) decommissioned bridges as a part of an ongoing project with SCDOT. The first is a Carbon Fiber Reinforced Plate (CFRP) retrofit where four CFRP plates were adhesively bonded to the bottom of a slab. The second is a steel plate that was mechanically attached to the bottom of a slab using bolted connections. The bolts were cast into grouted holes in the slab. To better understand the failure mode of these retrofits and their …

Assessment Of Bridge Pier Response To Fire, Vehicle Impact, And Air Blast, Chen Fang, Qusai Alomari, Daniel G. Linzell

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Highway bridges exposed to intentional or unintentional fire followed by combined vehicle impact and air blast are at risk of significant damage and, possibly, collapse. Limited studies examining the complex effects of these extreme demands on bridge support elements and parametrizing their response and damage are found in the open literature. Research that is presented is part of an ongoing numerical investigation examining round, multi-column, reinforced concrete (RC), bridge pier behavior subject to multi-hazard scenarios involving fire, vehicle impact, and air blast. Detailed nonlinear finite element analysis models of single columns and multi-column piers supported by a pile foundation system …

Evaluating The Effects Of Shored Construction On Steel Girder Composite Bridges, Parker Brooks

Doctoral Dissertations and Master's Theses

Steel composite girder bridges provide economic advantages and higher load-carrying capacity than non-composite alternatives. Over the years, a conventional sequence of un-shored construction for steel girder composite bridges has been developed. There is an alternative construction sequence, known as shored construction, that uses temporary supports (discretely or fully supported) for the superstructure during the installation of metal forms and the pouring of concrete. Shored construction also can be used in an Accelerated Bridge Construction (ABC) practice where construction occurs at a nearby site and fully-formed elements are transported to the final site using self-propelled modular transporters (SPMTs). In order to …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Lessons Learned From Six Different Structural Health Monitoring Systems On Highway Bridges, Abheetha Peiris, Charlie Sun, Issam E. Harik

Kentucky Transportation Center Faculty and Researcher Publications

Structural health monitoring has been utilized in numerous ways to investigate the performance and integrity of highway bridges. This paper highlights the use of six structural health monitoring systems, which were deployed to monitor distinct behaviors on six bridges in Kentucky. The structural health monitoring systems are as follows: (1) Over-height truck impact detection and monitoring on the I-64 over US 60 bridge, (2) Barge impact detection and monitoring on northbound US 41 over the Ohio River, (3) effectiveness of carbon fiber-reinforced polymer retrofit evaluation based on prestressed concrete I-girder crack movement on the I-65 elevated expressway in Louisville, (4) …

Bridge Resilience Assessment With Inspire Data, Iris Tien, Yijian Zhang

Project RR-1

This project proposed a methodology to assess the impact of corrosion on the performance of bridges. The combined analytical and numerical modeling of shear-critical and lap-spliced columns is detailed, and outcomes are verified with previous experimental test data. The impact of corrosion on risk is assessed through conducting fragility analyses. Results quantify the increase in failure probabilities of these structures, measured by increasing probabilities of exceeding defined damage states, with increasing levels of corrosion. Corrosion is found to have a larger impact on increasing probabilities of exceeding more severe damage states. Twenty percent mass loss of reinforcement increases the probability …

Uav-Enabled Measurement For Spatial Magnetic Field Of Smart Rocks In Bridge Scour Monitoring -- Technical Report (2017-2020), Genda Chen, Haibin Zhang, Zhaochao Li

Project SN-1

This project proposed an unmanned aerial vehicle (UAV)-based method to measure the change in magnetic field as a result of the movement of a smart rock to monitor the maximum depth of bridge scour. A high resolution 3-axis magnetometer and global positioning system (GPS) unit were installed on the UAV to obtain the magnetic field intensity and its corresponding coordinate. The optimization algorithm for the localization of smart rock was demonstrated and adopted. The impact factors on accurate smart rock positioning were experimentally investigated. Utilizing finite element method, the influence of steel reinforcing bars on the distribution of ambient magnetic …

Steel Bridge Truss Analysis, Alastair Seed

Williams Honors College, Honors Research Projects

The purpose of this project is to conduct a study comparing the effectiveness of different cross frame orientations in lowering the deflection of the main stringers of a bridge. Three different orientations of cross frames were researched; vertical, angled with the superstructure webbing, and halfway-angled. All of these were studied when the stringers were placed directly under the superstructure and when the superstructure was placed outside of the stringers. Analysis was performed in a program called SAP 2000 to find the deflections along the stringers under different loading conditions. The results showed that when the superstructure was oriented over the …

Structural Vulnerability Of Coastal Bridges Under Extreme Hurricane Conditions, Arturo Montoya, Adolfo Matamoros, Firat Testik, Reza Nasouri, Adnan Shahriar, Arsalan Majlesi

Publications

This work presents the results of a numerical study evaluating the response of coastal bridges due to hurricane-induced waves. The analyses were conducted using the Coupled Eulerian-Lagrangian (CEL) approach, available on the commercial finite element software Abaqus, which allows modeling the interaction between water and the bridge. The work concentrated on (1) establishing an approach for modeling the desired wave characteristics (i.e., wave height, and frequency) within the CEL simulation, (2) conducting simulations using actual bridge dimensions of historically damaged bridges, (3) analyzing a range of foundation flexibilities to determine its effect on the uplift and shear forces acting on …

Pedestrian Bridge In Tanzania, Maja Sagaser, Karina Rosales

Architectural Engineering

This senior project originated to address the need of the community of Same, Tanzania. There is a deep and wide ravine which floods, making the path many adults and children take to the Majevu Primary School increasingly difficult and dangerous. This report encapsulates all of the steps taken to complete an approved final design for a footbridge to be constructed over this ravine. It includes the project overview, the architectural and structural design process, as well as the important considerations. There are also structural drawings that include plans, elevations, and details.

2019 Student Steel Bridge Team, Kourtney Arena, Andrew Biglin, Brett Palmer, Nathaniel Maute, Kenneth Reiser, Jacob Dicks, Paul Kowaleski

STEM Student Research Symposium Posters

Every year AISC runs a regional and national steel bridge competition. The competition offers a chance for civil engineering students to gain valuable experience designing a bridge. In addition to this, mechanical engineering students are provided the opportunity to practice machining steel parts. For the competition, teams from participating schools are given a scenario with certain constraints to design a bridge for. At the competition, the bridges are ranked based on weight, structural efficiency, construction economy, assembly speed, deflection, aesthetics, and overall performance.

The program Risa 3D was used in order to design and perform analysis on the bridge. Using …

Developing Computer Codes For Analyzing Bridge Response Due To Wim Data Truck Loading, Kenneth Patrick Pasley

Graduate Theses and Dissertations

Despite actual truck demographics evolving over the past 30 years, the Arkansas legal loads for bridge posting have not been updated. Custom computer codes were developed.to facilitate comparison between the current Arkansas legal loads for bridge posting and the actual Arkansas truck traffic to ensure that actual reactions are enveloped by the state'. The program, WIMFluence, calculates shear and moment influence lines for a bridge and the resulting shear and moment reactions based on weigh-in-motion data. With supporting scripts, the reactions due to actual Arkansas truck traffic were compared to those due to the current Arkansas legal loads for bridge …

The Live Load Response Of The Open Web Steel Joist Black Slough Bridge, Piero Caputo

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

The bridge being studied spans the Black Slough River in the Nucor/Vulcraft facilities near Brigham City, Utah. The bridge is composed of seven heavyweight open web steel joists supporting a concrete deck-slab element and sitting in two concrete cantilever walls serving as bearings. A full-scale live-load test was performed using forklift vehicles at four locations on the deck. During the test, axial strains, deflections, and rotations where measured.

In their provisions, the American Association of State Highway and Transportation Officials (AASHTO) included a simplified number of equations and solutions used to calculate GDFs for standardized decks supported by beam systems. …

New Connection Details To Connect Precast Cap Beams To Precast Columns Using Ultra High Performance Concrete (Uhpc) For Seismic And Non-Seismic Regions, Mohamadreza Shafieifar

FIU Electronic Theses and Dissertations

Several connection details have been developed for the connection of precast cap beams to precast columns in Accelerated Bridge Construction (ABC) applications. Currently, the suggested details involve some form of either reinforcement or portion of the precast column to penetrate inside the cap beam. Such details present many challenges in the field, such as necessitating bundling of reinforcement in the cap beam or creating a congested reinforcement arrangement. Furthermore, closer inspection of some of the test data indicates that for currently used details, cap beams could sustain some damages during major seismic events, whereas they are designed to be capacity …

Development Of Iowa Dot Combination Bridge Separation Barrier With Bicycle Railing, Chaz M. Ginger

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The Iowa Department of Transportation typically builds separation barriers between vehicle and pedestrian/bicycle facilities when sidewalks or trails are present on vehicular bridges. Currently, Iowa DOT employs a combination bridge rail that utilizes a concrete parapet that previously had been successfully evaluated to National Cooperative Highway Research Program (NCHRP) Report 350 Test Level 4 (TL-4) criteria for these situations. While the parapet had been successfully evaluated, the combination bridge rail system as a whole had not been evaluated to any crash test standards. Iowa DOT desired that researchers at Midwest Roadside Safety Facility (MwRSF) design and test a combination bridge …

Effects Of Short-Term Strains On Concrete Bulb-Tee Bridge Girders And Analysis Of The Practicality Of Using Three-Dimensional Models Based On Drone Imagery To Aid In Bridge Inspections, Justin M. Pace

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

The University Transportation Center at Utah State University sponsors research through the Federal Highway Administration’s University Transportation Center Program. The purpose of this research is to advance technology and expertise in transportation-related fields. This includes research pertaining to bridge design, monitoring, and inspection (the focus of this research).

The first focus area of this research monitored short-term strains at the bottom of girders in a concrete bulb-tee girder bridge. The strains were caused by traffic loading and recorded using strain transducers attached to the bottom of each bridge girder. Patterns in the strain loading were monitored to draw conclusions about …

Structural Identification And Assessment Of The Inverted Tee Girder Bridge System, Garrett P. Martindale

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The Inverted Tee (IT) girder bridge system was originally developed in 1996 by the University of Nebraska–Lincoln (UNL) and Nebraska Department of Roads (NDOR) engineers. This bridge system currently accounts for over 110 bridges in Nebraska used for both state highways and local county roads. Excessive transverse and longitudinal deck cracking has been observed and noted in numerous bridge inspection reports. Since the IT girder bridge system is relatively new, limited data and knowledge exist on its structural performance and behavior. This study evaluates the IT girder bridge system by conducting twenty field observations as well as recording accelerometer time …

Bio-Inspired Hybrid Vibration Control Methodology For Intelligent Isolated Bridge Structures, Mariantonieta Gutierrez Soto

Civil Engineering Faculty Publications

Inspired by evolutionary game theory, the biological game of replicator dynamics is investigated for vibration control of bridge structures subjected to earthquake excitations. Replicator dynamics can be interpreted economically as a model of imitation of successful individuals. This paper uses replicator dynamics to reduce vibrations while optimally allocating the control device forces. The control algorithm proposed is integrated with a patented neural dynamic optimization algorithm to find optimal growth rate values with the goal of achieving satisfactory structural performance with minimum energy consumption. A model is described for hybrid vibration control of smart highway bridge structures subjected to earthquake loading.

Characterization Of Unknown Bridge Foundations, Saman Rashidyan

Civil Engineering ETDs

The National Bridge Inventory (NBI) recognized 86,133 bridges in the United States have no foundation data on record in 2003. It is evident that an unknown percentage of the 86,133 bridges identified by NBI with missing foundation data could also be highly vulnerable to scouring induced by water flow coupled with erodible soils. Conventional excavation, coring and boring excavations to identify unknown bridge foundation depths and types are deemed to be expensive, destructive, and limited in their application to the unknown foundation problem. Many surface and borehole nondestructive testing (NDT) technologies have been developed for this purpose. Three economical proven …

Experimental And Analytical Study Of Dynamic Behavior Of Bridge Superstructures Subjected To Overheight Vehicle Collisions, Yuan Jing

Doctoral Dissertations

The increasing occurrence of over-height vehicle collisions with bridges in the United States leads to concern about the damage due to lateral impact to bridge superstructures by over-height vehicles. However, this issue is not fully addressed in current bridge specifications. Previous researchers have conducted a number of small-scale tests to study the impact process. Also, finite element method (FEM) has largely been used to analyze the complicated collision mechanism.

A full-scale lateral impact testing facility was designed and built on a construction site in Knoxville, Tennessee, United States. An AASHTO Type-I prestressed concrete (PC) girder and a Hybrid Composite Beam …

Bridge Deck Research At The University Of Tennessee: A Summary Thesis, Lindsey Brooke Phelps

Masters Theses

Currently, there has been no compilation of all the research the University of Tennessee has completed on chloride ion penetration in concrete bridge decks. The following thesis is a brief summary of the work that has been completed under Dr. Edwin Burdette’s direction over the last six years along with some additional literature review. The testing consisted of Surface Resistivity and Rapid Chloride Ion Penetration testing. This testing showed that there is, in fact a correlation between the two test methods, though SR testing is much easier to conduct. Considerable testing was completed on bridge decks throughout the state of …

Seismic Design Of A Prestressed Concrete Bridge, Alperen Ozel

University of New Orleans Theses and Dissertations

Latest advancements in software have become an indispensable tool in structural analysis. The main goal of this thesis is to examine dynamic responses of bridges in seismic activity with the help of such tool as CSi Bridge. Therefore, throughout this study, a prestressed concrete bridge model will be thoroughly designed. In the first section, the required materials and structural components will be introduced. The following section will cover calculations required for modeling. The actual modeling of the structure will be carried out in Section 3. In Section 4, the set of required analysis for seismic design such as modal, pushover …

Integrated Solar Technologies With Outdoor Pedestrian Bridge Superstructure Decking, Richard K. Racz

Masters Theses

Solar technology has been a major topic in sustainable design for many years. In the last five years, however, the solar technology industry has seen a rapid growth in installations and technological advances in cell design. Combined with a rapidly declining overall system cost, the idea of introducing solar technology into a wider range of applications is becoming a focus for engineers and scientists around the world. So many variables which alter solar energy production, such as the sun and surrounding environment, determine whether a solar design is beneficial. This thesis presents a bridge deck surface integrated with solar cells …

State Of Accelerated Bridge Construction (Abc) In The United States, Mike Ofili

Honors College Theses

The purpose of this project is to develop a toolkit for the design and construction of bridges using prefabricated materials primarily to reduce the closure time and on-site construction time of newly constructed bridges or bridges undergoing renovation. The research focuses specifically on short span bridges in Georgia (40,60,80, and 120ft spans).

Areas of primary concern for this project were design, constructability, structural analysis, the use of concrete and steel girders, cost efficiency, and industry surveys. In this particular portion of the study, the surveys proved to be most effective when combined with information obtained existing research as well as …

A Review Of Probabilistic Methods Of Assessment Of Load Effects In Bridges, Eugene J. Obrien, F Schmidt, Donya Hajializadeh, X-Y Zhou, Bernard Enright, Colin C. Caprani, Simon Wilson, Emma Sheils

Articles

This paper reviews a range of statistical approaches to illustrate the influence of data quality and quantity on the probabilistic modelling of traffic load effects. It also aims to demonstrate the importance of long-run simulations in calculating characteristic traffic load effects. The popular methods of Peaks Over Threshold and Generalized Extreme Value are considered but also other methods including the Box-Cox approach, fitting to a Normal distribution and the Rice formula. For these five methods, curves are fitted to the tails of the daily maximum data. Bayesian Updating and Predictive Likelihood are also assessed, which require the entire data for …

Nonlinear Analysis Of Isotropic Slab Bridges Under Extreme Traffic Loading, Donya Hajializadeh, A. Salam Al-Sabah, Eugene J. Obrien, Debra F. Laefer, Bernard Enright

Articles

Probabilistic analysis of traffic loading on a bridge traditionally involves an extrapolation from measured or simulated load effects to a characteristic maximum value. In recent years, Long Run Simulation, whereby thousands of years of traffic are simulated, has allowed researchers to gain new insights into the nature of the traffic scenarios that govern at the limit state. For example, mobile cranes and low-loaders, sometimes accompanied by a common articulated truck, have been shown to govern in most cases. In this paper, the extreme loading scenarios identified in the Long Run Simulation are applied to a non-linear, two-dimensional (2D) plate finite …

Spatial Time-Dependent Reliability Analysis Of Reinforced Concrete Slab Bridges Subject To Realistic Traffic Loading, Donya Hajializadeh, Mark Stewart, Bernard Enright, Eugene J. Obrien

Articles

Resistance and loads are often correlated in time and space. The paper assesses the influence of these correlations on structural reliability/probability of failure for a typical two-lane RC slab bridge under realistic traffic loading. Spatial variables for structural resistance are cover and concrete compressive strength, which in turn affect the strength and chloride-induced corrosion of RC elements. Random variables include pit depth and model error. Correlation of weights between trucks in adjacent lanes and inter-vehicle gaps are also included and are calibrated against Weigh-In-Motion (WIM) data. Reliability analysis of deteriorating bridges needs to incorporate uncertainties associated with parameters governing the …

Field And Analytical Studies Of The First Folded Plate Girder Bridge, Man Hou Sit

Masters Theses

Integral abutment bridges are very common for short span bridges in the United State due to their less construction and maintenance cost and generally good performance. This thesis studies the first integral abutment bridge using Folded Plate Girder (FPG) Bridge System. The bridge is instrumented with a variety of gauges to capture the behavior of the bridge, and a total of two year and one month [11/2011~12/2013] of data are collected and long-term data monitoring is performed. Live load test and long term temperature effect on the bridge are studied using finite element modeling and compared with actual field data. …

International Conference On Short And Medium Span Bridges, Calgary, July 15-18, 2014, Barry A. Palynchuk Phd, Christophe Deniaud Phd

Barry A. Palynchuk PhD

The Jean River near Wabush, Labrador is crossed by two railways and an access road by twin 6m diameter culverts . They are heavily strutted inside their barrels to counteract some significant shape deformation, and are deemed not suitable to sustain the increased volume of rail traffic serving the development of the Bloom Lake mines. The owner requested the design and construction of a replacement scheme for an additional design life of 20 years with a time sensitive schedule for completion of the work during the 2013 construction season. This VE concept for the design of live load relief spans …

Development Of Bridge Girder Movement Criteria For Accelerated Bridge Construction, Genda Chen, Yi Bao

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

End diaphragms connect multiple girders to form a bridge superstructure system for effective resistance to earthquake loads. Concrete girder bridges that include end diaphragms consistently proved to perform well during previous earthquake events. However, whether concrete bridges without end diaphragms are definitively inadequate in seismic performance is yet to be answered. The 2010 Chile Earthquake indicated that properly designed bridge girders and their lateral movement stoppers (shear keys) may perform equally well with those with end diaphragms. In this report, a feasibility study on the design of girder bridges without end diaphragms is presented. This study is particularly significant in …