Engineering Commons^™

Modeling And Computer Simulation Of Fault Calculations For Transmission Lines, Dr. Adel A. Elbaset

Dr. Adel A. Elbaset

Calculation of transmission line faults has a fundamental importance in the fault detection, classification, and location determination of faults in transmission line. This paper presents a proposed computer program based on Matlab software to calculate all ten types of shunt faults that may occur in a transmission line. Various fault scenarios (fault types, fault locations and fault impedance) are considered in this paper. The inputs of the proposed program are line length, source voltage, positive, negative and zero sequence for source impedance, line charging, and transmission line impedance. The output of the algorithm is used to train an artificial intelligence …

Comparative Evaluation Of Pid Voltage Mode, Pi Current Mode, Fuzzy And Pwm Based Sliding Mode Control For Dc-Dc Converters, Omar Ellabban, Joeri Van Mierlo

Omar Ellabban

This paper presents a comparison between the application of four control techniques in DC-DC converters. PID voltage mode (PID-VM), PI current mode (PI-CM), fuzzy, and PWM based sliding mode (SM) controllers are applied to buck converter. The design procedures of controllers are reviewed. The dynamic performance of these controllers under star-up, steady state, input voltage variation, load current disturbances and EMI spectrum are presented and compared.

Stability Analysis Of A Unified Power Flow Controller, Omar H. Abdalla, Mohamed A. E. Ghazy, Lotfy M. Lotfy, Nermeen A. M. Hassan

Omar H. Abdalla

The paper concerns with stability analysis of a Unified Power Flow Controller (UPFC). A nonlinear model is described in the abc-reference frame and then transformed into the dq0-reference frame. The model includes shunt and series compensators of the UPFC. Stability analysis is presented first in a three-dimensional space of system parameters. A linearized model is obtained in state-space form to be used in small-signal stability studies. Effects of system parameters on stability are investigated using eigenvalue analysis. These include resistance, reactance, and modulation indices of the shunt and series components of the UPFC. Simulation results show that the stability of …

Exercise Power Grid Display And Web Interface, Alexander (Alex) Chernetz

Computer Engineering

The 2008-2009 expansion of the Recreation Center at Cal Poly includes three new rooms with cardiovascular fitness equipment. As part of its ongoing commitment to sustainable development, the new machines connect to the main power grid and generate power during a workout. This document explains the process of quantifying and expressing the power generated using two interfaces: an autonomous display designed for a television with a text size and amount of detail adaptable to multiple television sizes and viewing distances, and an interactive, more detailed Web interface accessible with any Java-capable computer system or browser.

Dc-Dc Converter For Harvesting Energy From An Exercise Bike, Henry Ureh, Chris Henry

Electrical Engineering

Create an efficient buck-boost converter that adapts to input voltage range from ~3.8V to 70V, and outputs 13.7V DC, the voltage required by a charge controller to charge a battery. The energy stored in the battery will be supplied back to the grid.

The cost of energy saved by the converter should eventually cover the initial price of the converter. The converter should help reduce the net power consumption of the exercise machines used in the Cal Poly gym

Lab-Scale Thyristor Rectifier And Static Var Compensator Circuits, Haroun Idris, Ibrahim Idris

Electrical Engineering

The purpose of this project is to design thyristor circuits by using single-phase FCRO 4100 firing board donated by ENERPRO. These circuits in conjunction with a thyristor module will be used for future lab experiments in power electronics courses.

The first part of this project is to study the full effect of a firing angle on a controlled single phase full bridge thyristor rectifier circuit. Furthermore, the resulting circuit setup will be implemented as part of future lab experiments in Power Electronics I course. The next purpose of this project is to design a small-scale Static VAR Compensator (SVC) lab …

Reflective Optics Cpv Panels Enabling Large Scale, Reliable Generation Of Solar Energy Cost Competitive With Fossil Fuels, S. Horne, M. Mcdonald, N. Hartsoch, K. Desy

Publications (E)

The objective of this 18 month subcontract was the improvement of reflective optics CPV panels to enable the large-scale, reliable production of solar electricity to meet SAI-established LCOE targets, and ultimately provide a path to solar power at parity with or better than the cost of energy generated utilizing fossil fuels. To this end, SolFocus has completed this subcontract with great success as evidenced by the end results of a CPV panel with conversion efficiencies greater than the targeted 22% and manufacturing capabilities with a run rate capacity far exceeding the milestone benchmark >3MW.

Wind Energy And Power System Operations: A Review Of Wind Integration Studies To Date, Jennifer Decesaro, Kevin Porter

Publications (E)

This paper provides an overview of the challenges associated with wind integration and summarizes the findings of the wind integration studies conducted over the course of the past five years. We begin with an overview of the approximate time frames used in grid operations. We then describe how wind integration studies are conducted, discuss the results on wind integration costs and grid impacts from these grid integration studies, and assess some of the grid planning and operation changes that may be necessary to incorporate higher levels of wind generation. We close with several conclusions.

Solar Panel Experiment, John Hauger

Electrical Engineering

This senior project will focus on creating a suitable testing procedure for the provided solar panel system. The testing parameters will be based on the expected 60W output power of the system. The complete procedure will provide a thorough analysis of the power flow and overall efficiency of the system.

This senior project report will discuss the importance of this experiment in the Electrical Engineering curriculum, the system requirements and parameters tested in the design, and the provided results based on the test conditions. In addition, this report will include the complete testing procedure and recommendations for possible future additions …

Energy Harvesting From Elliptical Machines: Dc Converter Troubleshooting, Michelle Lum, Jonathan Yuen

Electrical Engineering

In continuing the global effort to integrate innovative technology and renewable energy in the world’s power system, Cal Poly endeavors to harvest energy from elliptical machines and feed that power back into the electrical grid. This continuation of the previous project, Energy Harvesting from Exercise Machines Self‐generating Elliptical Machines, seeks an alternative DC to DC converter to function within the existing elliptical self‐generating system. By attempting to implement this new DC to DC converter, the project strives to reduce the size of the converter in order to mount it on the elliptical machine. The project also tries to explain how …

Switching Circuit For A Permanent Magnet Dc Motor, Alex Boatman

Electrical Engineering

The project is a circuit that will basically supply current from the battery to the different stator coils at opportune moments. With a hall-effect sensor on the shaft as a feedback to a microcontroller, I was able to toggle switches based on the position of the shaft at the moments where we would be using as little power as possible. The operation of the control circuit works similar to a stepper motor; it takes a signal from the microcontroller that is sent to some FET drivers, which in turn sends signals to the FETs to open or close as the …

Overcurrent Coordination Study, Edwin Pho

Electrical Engineering

No abstract provided.

Synthesis Of Α-Mno_2 Microspheres For The Application In Supercapacitor, Liang Wang, Gui-Chang Liu, Zhi-Cong Shi

Journal of Electrochemistry

The MnO2 microspheres were prepared through the oxidation of KMnO4 and MnCO3 microspheres precursor.The microstructure and supercapacitor properties of MnO2 were characterized by XRD,SEM and CV.The results show that MnO2 was in a poorly crystalline state with α-crystallographic form,the size of microspheres typically ranged from 0.5 to 2 μm.Loading 5 mg·cm-2 MnO2 microspheres had excellent capacitance behaviors in 2 mol·L-1(NH4)2SO4 solution.The specific capacitance was 135.6 F·g-1 with the scan rate at 2 mV·s-1,and 118.8 F·g-1 with the large scan rate at 100 mV/s.Coulumbic efficiency was still above 87.8% in the 500 cycles,and the specific capacitance of the 500th cycle was …

Synthesis And Electrocatalytic Properties Of Ni-Pd/C Catalysts With Pd-Enriched Surface, Yu-Mei Chen, Zhi-Xiu Liang, Sheng-Li Chen

Journal of Electrochemistry

The Ni-Pd alloy catalysts with Pd-enriched surface were synthesized through a modified polyol process.The synthesized materials were investigated by XRD and electrochemical methods,and tested as electrocatalysts for CH3OH-tolerant oxygen reduction.The results indicated that the synthesized Ni-Pd nanoparticles possess multiple phases containing Pd-Ni alloy and pure Ni.Comparing with Pd/C,the prepared Ni-Pd/C nanoparticles exhibited better resolved voltammetric peaks between the hydrogen absorption and adsorption,and positively shifted current peaks for the reduction of Pd oxide.The prepared Ni-Pd alloys with Pd-enriched surface have significantly enhanced ORR activity and improved CH3OH tolerance as comparing with Pd/C catalysts.

Research Progress Of Synergistic Effect Of Metal Oxides On Pt-Based Catalysts, Hui-Ping Yuan, Xun Guo, Xin-Ping Qiu, Wen-Tao Zhu, Li-Quan Chen

Journal of Electrochemistry

In this paper,the work of Pt-based catalysts modified by metal oxides as the anode catalysts of direct methanol fuel cell(DMFC) is reviewed.The relationship between the structure and the composition of the catalysts and the reaction mechanism,exiting problems and developing direction are discussed.

Highly Durable Pt/Ruo_2/C Catalyst For The Cathode Of Direct Methanol Fuel Cells, Chun-Yu Du, Tao Dong, Ge-Ping Yin, Peng-Fei Shi

Journal of Electrochemistry

Instability of the carbon-supported Pt(Pt/C) catalyst at the cathode is one of the key technical challenges for the development of Direct Methanol Fuel Cells(DMFCs).In this paper,an efficient approach to enhancing the stability of the cathode catalyst was explored by designing and synthesizing a novel nanocomposite support,RuO2 coated carbon black(RuO2/C).Firstly,a wet chemical method was employed to synthesize the RuO2/C nanocomposite,from which Pt/RuO2/C catalyst was further prepared by a microwave method.The morphology and crystalline structure of the RuO2/C support and Pt/RuO2/C catalyst were then characterized by TEM and XRD.Finally,the electrochemical performance of the RuO2/C support and Pt/RuO2/C catalyst was analyzed by cyclic …

Indirect Electrosynthesis Of Double Aldehyde Starch Using Pb-(Bro_3~-/Br~-) As Electro-Catalytic Mediator, Chen Ni-Na, Chen Ri-Yao, Xi Zheng, Chen Xiao, Zhen Chen

Journal of Electrochemistry

In this paper,Nafion membrane was used as the separator in the electrolysis cell to indirectly electro-generating the double aldehyde starch(DAS) with BrO-3/Br-as a redox mediator and Pb as an anode.Effects of temperature,concentration of sulfuric acid and starch on the electro-oxidation of DAS were discussed.The steady state polarization curves were obtained.The experiment results showed that the current efficiency was over 50% when the electrolysis current density was 15mA/ cm2.

Platinum Modified With Hydrogen Molybdenum/Tungsten Bronze As Electrocatalysts For Direct Small Organic Molecule Fuel Cell, Wei-Shan Li, Li-Peng Tian, Jun-Hua Du, Hong-Liang Huang, Wei Li, Li-Xia Zhang, Hong-Yan Yang, Pan-Pan Guo, Zhi-Hui Zhou, Xing-De Xiang, Zhao Fu

Journal of Electrochemistry

There are several problems that limit the application of direct small organic fuel cell,including the use of precious platinum and the activity loss of platinum due to the intermediates poisons from the oxidation of small organic molecules.These problems have attracted wide interest and many solutions have been proposed.We have developed a new method to reduce the platinum usage and improve its activity,based on the modification of platinum with hydrogen molybdenum/tungsten bronze(HxMo(W)O3,0

Preparation Of Pt Nanoflower/Zno Composites Arrays And Their Electrocatalysis For Methanol Oxidation, Li Gao, Yi-Feng E, Lou-Zhen Fan

Journal of Electrochemistry

The Pt nanoflower/ZnO(PtNF/ZnO) nanorod composites arrays were electrochemically prepared by controlling the hydrophobicity and the hydrophilicity of ZnO nanorods arrays.The Pt nanoflowers grew on the tip of ZnO nanorods,which maintain the vertical array of Zno nanorods with a high degree of size uniformity and high surface area.Compared with Pt nanoparticle covered ZnO nanorod arrays,which were prepared by controlling the hydrophilicities of ZnO nanorods and Pt nanoparticles,the PtNF/ZnO displayed highest electrocatalytic activities for the oxidation of methanol.

Enhanced Visible Light Photoelectrochemical Performances With Nitrogen Doped Tio_2 Nanowire Arrays, Xiao-Jun Lv, Yue-Ming Li, Hao Zhang, Da Chen, Hensel Jennifer, Z Zhang Jin, Jing-Hong Li

Journal of Electrochemistry

Self-organized anodic anatase TiO2nanowire arrays doped with nitrogen have been successfully fabri-cated and their photoelectrochemical(PEC) properties have been characterized and found to be substantially im-proved compared to undoped nanowires or commercial P25 nanoparticles.Photocurrent measured with monochro-matic incident light showed that the incident photon-to-current efficiency(IPCE,%) values of nanowire arrayelectrodes with or without N-doping were obviously higher than that of commercial P25 nanoparticle electrodes,and nitrogen-doped TiO2nanowire arrays(NTNA) had noticeable absorption in the visible region.The NTNAelectrodes showed the highest photocurrent density and power conversion efficiency under 100 mW/cm2visiblelight illumination.A maximumolphotoconversion efficiency of 0.52% was achieved for the NTNA sample at anapplied potential of …

Enhanced [Ru(Bpy)_3]~(2+)-Mediated Oxidation Of Guanine Prompted By Dhp, Bao-Lian Zhang, Wei Hong, Bao-Yi Lu, Hong Li

Journal of Electrochemistry

The effects of dihexadecyl phosphate(DHP) and multi-walled carbon nanotubes(MWNTs) on the oxidation of guanine mediated by[Ru(bpy)3]2+ on the ITO electrode have been investigated by cyclic voltammetry and differential pulse voltammetry.The results showed that [Ru(bpy)3]2+ can mediate the oxidation.In the range from 0.01 to 0.15 mmol·L-1,peak currents for guanine oxidation mediated by [Ru(bpy)3]2+ increased with the rise of DHP concentrations.On the contrary,cationic surfactant HTAC has the ability to weaken the mediated oxidation of guanine.In addition,the oxidative mechanism of guanine mediated by [Ru(bpy)3]2+ with the participation of DHP is discussed.

Electrocatalysis Of Myoglobin-Chitosan-Au Colloid Film Modified Glass Carbon Electrode, Yu-Hua Qin, Jun Guo, Hui Xu, Li-Heng Zhou, Sheng-Tian Wang

Journal of Electrochemistry

The cyclic voltammgram of Mb/AAO/Au Colloid/GCE shows a pair of well-defined and nearly reversible peaks at about-0.20 V(vs.Ag/AgCl) in 0.1 mol/L NaAc-HAc buffer(pH = 5.4),being the characteristic peaks of the Mb heme Fe(Ⅲ) / Fe(Ⅱ)redox couples.The electron transfer between Mb and the electrode was greatly enhanced under present testing conditions.The effects of scan rate,pH and buffers concentration on the electrochemical behaviors of Mb were studied in detail.Position of the Soret absorbance band suggested that Mb in chitosan-colloidal gold hept its secondary structure similar to the native states.Oxygen was catalytically reduced by Mb in chitosan-colloidal gold films.

Progresses In Electrocatalysis Of Nanomaterials—Tuning The Surface Structure And Property Of Electrocatalysts, Yan-Xia Jiang, Na Tian, Zhi-You Zhou, Sheng-Pei Chen, Shi-Gang Sun

Journal of Electrochemistry

The property of an electrocatalyst depends strongly on its surface structure.The study of surface structure-catalytic functionality is the base of design and preparation of electrocatalysts of high activity,high stability and high selectivity at microstructure level.In this paper,based mainly on our results concering hydrogen and oxygen adsorption-desorption,ethylene glycol oxidation and CO2 reduction,the research progresses in tuning the surface structure and property of electrocatalysts are summarized.This paper overviews firstly the cyclic voltammetric characteristics,electrocatalytic properties of platinum single crystal planes lying on different crystallographic zones of the unit stereographic triangle of face-centered cubic(fcc) metals.Next,the innovation of electrochemical methods to control the surface structure …

Electrooxidation Of Formic Acid On Pd-Ni Alloy Film Electrode-The Effect Of Dealloying, Chao Wang, Fei-Fei Shi, Jin-Yi Wang, Han-Xuan Zhang, Wen-Bin Cai

Journal of Electrochemistry

A Pd-Ni alloy film was electrodeposited on Au disc electrode at a constant potential from a weakly basic bath containing PdCl2,NiSO4 and ethylenediamine.The as-deposited film was then subjected to potential cycling in a perchloric acid solution for surface dealloying treatment.The dealloyed Pd-Ni film electrode was examined for the electrocatalytic oxidation of formic acid,and compared with the as-deposited one as well as a Pd film electrode.The FE-SEM and electrochemical measurements on the Pd-Ni films revealed that the dealloying treatment caused a surface roughening and an increase in specific surface reaction area.The ICP-AES and XPS analyses demonstrated that the preferential dissolution of …

Complex Reduction Preparation Of Carbon Supported Pd Nanoparticle Catalyst And Its Electrocatalysis For Formic Acid Oxidation, Wei He, Yong-Yin Kang, Chong Du, Zhi-Qing Zou, Xiao-Gang Zhang, Hui Yang

Journal of Electrochemistry

A simple procedure involved the complexing of PdCl2 with sodium citrate followed by ethylene glycol reduction has been employed for the preparation of carbon-supported Pd nanoparticles(Pd/C).The XRD and TEM characterizations indicate that Pd nanoparticles with a small particle size were well-dispersed on carbon support.The mean particle sizes of the Pd/C catalysts were found to be increased from 2.7 to 5.8 nm with heat-treatments at different temperature.The mass activity of the Pd/C catalyst for formic acid electrooxidation increased with the decrease in Pd particle size.However,the specific activity increased with Pd particle size.Furthermore,the Pd/C catalyst with a particle size of ca.3.6 nm …

Electrocatalytic Performance Of Carbon Supported Ir Catalysts With Different Ir Loadings For Ammonia Oxidation, Yu-Zhi Jiang, Qing-Mei Kong, Tian-Hong Lu, Yi-Ming Zhou, Ya-Wen Tang

Journal of Electrochemistry

The electrocatalytic performance of the Ir/C catalyst as the anodic catalyst in the amperometric and electrochemical NH3 sensor was investigated.The experimental results illustrated that in the NaClO4 neutral electrolyte,the electrocatalytic performance of the Ir/C catalyst for the NH3 oxidation is related to the Ir loading in the Ir/C catalyst.Among the Ir/C catalysts with different Ir loading,the best electrocatalytic activity,stability and sensitivity were achieved by the Ir/C catalyst with 10% Ir loadings.In addition,the current densities of the NH3 oxidation at the Ir/C catalysts with the different Ir loadings were linearly proportional to the NH3 concentration.The Ir/C catalyst has a potential application …

Cyclic Voltammetric And In-Situ Ftir Spectroscopic Studies Of Adsorption And Reduction Of No On Electrode Of Pt Nanoparticles, Qian Cheng, Yan-Xia Jiang, Dong-Mei Zeng, Shi-Gang Sun

Journal of Electrochemistry

Adsorption and reduction of NO on electrode of Pt nanoparticles in acid solutions were studied by means of cyclic voltammetry(CV) and in-situ FTIR spectroscopy.The results indicated that the reduction of NO is a complicated process including the adsorption of NO on electrode surface.Two types of surface-bonded NO were determined on Pt nanoparticles.The weakly adsorbed NO was reduced between 0.6 V and-0.05 V,which yielded nitrous oxide(N2O) and ammonium(NH+4) as products;while the strongly bonded NO was reduced at more negative potentials between-0.05V and-0.15V,producing only NH4+ species.

Electrocatalysis In Polymer Electrolyte Membrane Fuel Cells, Li Li, Si-Guo Chen, Xue-Qiang Qi, Yao-Qiong Wang, Meng-Bo Ji, Lan-Lan Li, Zi-Dong Wei

Journal of Electrochemistry

This review presents the study of Chongqing University in electrocatalysis for polymer electrolyte membrane fuel cells(PEMFCs).Based on the understanding to the performance degradation of PEMFCs' catalysts,the university has being concentrated on how to increase the activity,stability and utility of noble metal catalysts.It covers the molecular design of near-surface alloy catalysts for improvement of activity to oxygen reduction reaction(ORR) and resistance to foreign poison species,selective deposition of Pt on the so-called "three-phase interface" for a high Pt utility,and invention of anti-flooding electrode against water flooding in the catalyst layer of the membrane assemble electrode(MEA),and so on.The catalytic mechanism of electrode reactions …

Electrocatalytic Activities Of Au-Mmni_(3.2)Al_(0.2)Mn_(0.6)Co_(1.00) For Borohydride Oxidation, Gui-Ling Wang, Jin-Cheng Liu, Ke-Ning Sun, Dian-Xue Cao

Journal of Electrochemistry

In this work,the electrocatalytic activities of MmNi3.2Al0.2Mn0.6Co1.0,NaOH treated MmNi3.2Al0.2Mn0.6Co1.0 and Au-MmNi3.2Al0.2Mn0.6Co1.0 obtained after NaOH treatment(Mm: misch metal) for NaBH4 oxidation were reported.The electrodes were prepared by electrodeposition,their morphologies were analysized by SEM,their electrocatalytic properties were studied by the linear sweeping test.It was found that the oxidation current density of the Au-MmNi3.2Al0.2Mn0.6Co1.0 was 60 mA·cm-2,it was 3.5 times higher than that at the MmNi3.2Al0.2Mn0.6Co1.0 electrode.In addition,the oxidation current density at the Au-MmNi3.2Al0.2Mn0.6Co1.0 electrode immersed in the electrolyte solution for 10 hours was 184 mA·cm-2.

A Pll-Based Multirate Structure For Time-Varying Power Systems Harmonic/ Interharmonic Estimation, Janison Rodrigues De Carvalho, Carlos A. Duque, Moisés V. Ribeiro, Augusto S. Cerqueira

University Faculty Publications and Creative Works

This paper describes a phase-locked-loop (PLL)-based power systems harmonic estimation algorithm, which uses an analysis filter bank and multirate processing. The filter bank is composed of bandpass filters. The initial center frequency of each filter is purposely chosen to be equal to harmonic frequencies. However, an adaptation strategy makes it possible to track time-varying frequencies as well as interharmonic components. A downsampler device follows the filtering stage, reducing the computational burden, especially because undersampling operations are performed. Finally, the last stage is composed of a PLL estimator which provides estimates for amplitude, phase, and frequency of the input signal. The …