Engineering Commons^™

Synergistic Effect Of Nanoclay And Barium Sulfate Fillers On The Corrosion Resistance Of Polyester Powder Coatings, Jinbao Huang, Marshall Shuai Yang, Chengqian Xian, James Joseph Noel, Yolanda S. Hedberg, Jian Chen, Ubong Eduok, Ivan Barker, Jeffrey Daniel Henderson, Haiping Zhang, Liqin Wang, Hui Zhang, Jesse Zhu

Chemistry Publications

No abstract provided.

Numerical Modeling And Simulation On Deformation And Failure Behaviors Of Polymeric Materials, Heng Feng

Electronic Thesis and Dissertation Repository

Featured by biocompatibility, high compliance and capacity in sustaining large deformation, dielectric elastomers (DEs) and hydrogels have gained extensive research popularity for their potential applications in the fields of soft robots, biomimetics, tissue engineering, drug delivery, and energy harvesting. The design of such soft and smart material-based devices and structures requires deep understanding and accurate simulation of their constitutive behaviors, which is challenged by their nonlinear material properties due to unique microstructures and multi-physics coupling. Meanwhile, in different application contexts, those structures are also susceptible to different failure modes, imposing further challenges in simulating and predicting their performance. To fulfill …

Enhanced Performance Of 3d Electroactive Polymer Transducers Via Hierarchical Structures, Frederick B. Holness

Electronic Thesis and Dissertation Repository

Conjugated polymers (CPs) are a class of polymers that exhibit a change in size or shape in response to electrical stimuli. The unique combination of electrical and mechanical properties facilitates the fabrication of novel devices in a broad range of applications including: sensors, actuators, and lab-on-a-chip systems. The alternating single and double bonds along the polymer chain of CPs enables their electroactive properties but is also responsible for processability associated with CPs that has limited fabrication methods. Recently a photosensitive CP composite enabling additive manufacturing (AM) of 3D CP structures was developed. However, the introduction of a copolymer for mechanical …

Rational Interface Design For High-Performance All-Solid-State Lithium Batteries, Changhong Wang

Electronic Thesis and Dissertation Repository

All-solid-state lithium batteries (ASSLBs) have gained substantial attention owing to their excellent safety and high energy density. However, the development of ASSLBs has been hindered by large interfacial resistance originating from the detrimental interfacial reactions, poor solid-solid contact, and lithium dendrite growth. The research in this thesis aims at achieving high-performance ASSLBs via rational interface design and understanding the interfacial reaction mechanisms.

At the cathode interface, an ideal dual core-shell nanostructure was first designed. Moreover, single-crystal LiNi_0.5Mn_0.3Co_0.2O₂ (SC-NMC532) cathode was compared with polycrystalline NMC532, the former exhibits much enhanced Li⁺ diffusion kinetics …

Synthesis Of Vo2/Poly(Mma-Co-Dmemuabr) Antimicrobial/Thermochromic Dual-Functional Coating And Reactivity Ratios Study, Yixian Liu

Electronic Thesis and Dissertation Repository

Antimicrobial/thermochromic dual-functional coatings were successfully synthesized via UV-curing. The quaternary ammonium compound (QAC) N,N-dimethyl-N-{2-[(2-methylprop-2-enoyl)oxy]ethyl}undecane-1-aminium bromide (dMEMUABr) was synthesized and copolymerized with methyl methacrylate (MMA) for antimicrobial properties. Vanadium oxide (VO₂) nanoparticles were evenly dispersed within the coating, providing thermochromic properties. The dual-functional coating showed high luminous transmittance (T_lum(25°C) =36.1 %) and solar energy modulation ( T_sol=5.8 %). 90.3 % of bacteria reduction was observed against Escherichia coli within 24 h contact. To further understand the sequence distribution of the copolymer poly(MMA-co-dMEMUABr), the reactivity ratios of MMA and dMEMUABr monomer were studied and compared under thermal …

Development Of Novel Solid-State Electrolytes For Sodium Ion Batteries, Fei Sun

Electronic Thesis and Dissertation Repository

Sodium ion battery is considered as a potential candidate to replace lithium ion battery. To eliminate the need for containment of the liquid electrolyte, the solid-state electrolytes attract more attention. However, solid state electrolytes are still restricted to be applied for commercialization because of the inherent low ionic conductivity and the poor mechanical properties. Therefore, my Ph.D. research is focused on developing advanced solid-state electrolytes by improving ionic conductivity and disclosing mechanisms of the electrolytes.

Firstly, a series of La substituted NASICON electrolytes are prepared to achieve high ionic conductivity of mS/cm, and the effects of La substitution concentration are …

Design Of Cell-Instructive Biomaterial Scaffolds For Intervertebral Disc Regeneration, Nadia Sharma

Electronic Thesis and Dissertation Repository

Biomaterials-based therapies targeting the nucleus pulposus (NP) have the potential to promote regeneration and restore mechanical function to the intervertebral disc. This study developed composite hydrogels incorporating decellularized NP (DNP) and assessed its effects on viability, retention and differentiation of U-CH1 cells, an NP progenitor-like cell line. A minimal protocol was developed to decellularize bovine NP that reduced nuclear content while preserving key extracellular matrix components predicted to be favourable for bioactivity. The resulting DNP demonstrated cell-instructive effects, supporting U-CH1 viability and retention within the hydrogels, and promoted the differentiation of the progenitor-like cells towards an NP-like phenotype. These studies …

Development Of Cellulose Nanofiber Reinforced Poly(Methyl Methacrylate), Tyler Bennett

Electronic Thesis and Dissertation Repository

Cellulose nanofiber (CNF), derived from renewable resources, is a good candidate to reinforce transparent plastics without sacrificing their transparency, owing to its size on the nano-meter scale, reflective index similar to the plastics’, excellent mechanical property, and low density. This study investigates effects of CNF on optical, viscoelastic, and thermal properties of CNF reinforced poly(methyl methacrylate) (PMMA). CNF/PMMA with different CNF contents and different types of PMMA were prepared through a solvent casting method with a low toxic and inexpensive solvent, acetone, and compression-molded to create nanocomposite films. The films were characterized using a transmission electron microscope, ultraviolet–visible (UV-Vis) spectrophotometry, …

Effect Of The Nonlinear Material Viscosity On The Performance Of Dielectric Elastomer Transducers, Yuanping Li

Electronic Thesis and Dissertation Repository

As a typical type of soft electroactive materials, dielectric elastomers (DEs) are capable of producing large voltage-induced deformation, which makes them desirable materials for a variety of applications in transduction technology, including tunable oscillators, resonators, biomimetics and energy harvesters. The dynamic and energy harvesting performance of such DE-based devices is strongly affected not only by multiple failure modes such as electrical breakdown, electromechanical instability, loss-of-tension and fatigue, but also by their material viscoelasticity. Moreover, as suggested by experiments and theoretical studies, DEs possess nonlinear relaxation processes, which makes modeling of the performance of DE-based devices more challenging.

In this thesis, …

Fabrication And Characterization Of Collagen-Polypyrrole Constructs Using Direct-Ink Write Additive Manufacturing, Rooshan Arshad

Electronic Thesis and Dissertation Repository

Current efforts in the tissue engineering field are being directed towards the creation of platforms which will facilitate in instructing cells towards biologically relevant outcomes such as stem cell differentiation and disease pathophysiology. Traditional fabrication methods serve as a limiting factor for the production of such platforms as they lack feature and geometric complexity. Additive Manufacturing (AM) offers advantage over said methods by affording designers creative freedom and great control over printed constructs. Such constructs can then be used to create appropriate models for study- ing a plethora of tissues and structures. An AM methodology for Direct-Ink Write (DIW) printing …

Additive Manufacturing Of Piezoelectric Photopolymer Ferroelectrets, Rami Abu Shammeh

Electronic Thesis and Dissertation Repository

Electroactive polymers are an emerging branch of smart materials that possess the capability to change shape in the presence of an electric field. Particularly, ferroelectrets are films of electrostatically charged dielectric polymer foam that comprise a growing portion of EAP literature. Ferroelectrets are characterized by a piezoelectric response and a quasi-permanent charge polarization owing to the dipoles created when the air cavities in the polymer matrix undergo dielectric breakdown. However, these cavities are often irregular in shape, size, and distribution when produced with conventional preparation methods. To overcome this, we employ a light-based additive manufacturing technique to create a hybrid …

Chemical Modification Of Lignin Into Advanced Materials, Soheil Hajirahimkhan

Electronic Thesis and Dissertation Repository

Fossil fuel resources are being used today for most of humankind’s energy and chemical/material needs. The inevitable demise of these resources has created significant interest in the field of biomass and particularly, lignin valorization. As the world’s second most abundant polymer, more than 98% of the annually produced lignin is under-utilized either as an on-site heat source, or as landfill. Thus, finding practical approaches to modifying this inexpensive sustainable resource into materials of high value can be the next leap in lessening the dependence on fossil fuel resources and thus, developing a sustainable future.

In this thesis, kraft lignin is …

Microinjection Molding Of Carbon Filled Polymer Composites, Shengtai Zhou

Electronic Thesis and Dissertation Repository

There has been increasing demand for microparts in the areas of electronics, automotive, biomedical and micro-electro-mechanical systems. Microinjection molding (μIM) is becoming an important technology to fabricate miniature products or components to satisfy the ever-increasing needs of the above industries. Polymers and polymeric composites are ubiquitously adopted as molding materials due to their weight advantage, good processability and excellent resistance to corrosion.

Earlier studies have been primarily focused on the μIM of unfilled thermoplastics; however, microparts with multi-functionalities, such as electrical, thermal and mechanical properties are always accommodated by using multi-functional filler loaded polymer composites. Recently, μIM of carbon nanotubes …

Effect Of Material Viscoelasticity On Frequency Tuning Of Dielectric Elastomer Membrane Resonators, Liyang Tian

Electronic Thesis and Dissertation Repository

Dielectric elastomers (DEs) capable of large voltage-induced deformation show promise for applications such as resonators and oscillators. However, the dynamic performance of such vibrational devices is not only strongly affected by the nonlinear electromechanical coupling and material hyperelasticity, but also significantly by the material viscoelasticity. The material viscoelasticity of DEs originates from the highly mobile polymer chains that constitute the polymer networks of the DE. Moreover, due to the multiple viscous polymer subnetworks, DEs possess multiple relaxation processes. Therefore, in order to predict the dynamic performance of DE-based devices, a theoretical model that accounts for the multiple relaxation processes is …

Development And Applications Of Polyglyoxylate Self-Immolative Polymers, Bo Fan

Electronic Thesis and Dissertation Repository

Self-immolative polymers (SIPs) are relatively recent class of stimuli-responsive and degradable polymers that have attracted significant attention in the past several years. SIPs consist of polymer backbones and stimuli-responsive end-caps at one or both polymer termini. Upon detection of a stimulus, the decomposition of the end-cap leads to complete end-to-end depolymerization. Polyglyoxylates were introduced as a new class of polyacetal based SIPs by our group in 2014. Compared with other SIPs, polyglyoxylates have two advantages including: 1) readily available monomers and 2) low toxic depolymerization products. These advantages may allow polyglyoxylates to be used in a wide range of applications. …

Fabrication Of 3d Conjugated Polymer Structures Via Vat Polymerization Additive Manufacturing, Andrew T. Cullen

Electronic Thesis and Dissertation Repository

Conjugated polymers are a class of electromechanically active materials that can produce motion in response to an electric potential. This motion can be harnessed to perform mechanical work, and therefore these materials are particularly well suited for use as sensors and actuators in microelectromechanical systems. Conventional methods to fabricate conjugated polymer actuators result in planar morphologies that limit fabricated devices to simplistic linear or bending actuation modes. To overcome this limitation, this work develops a conjugated polymer formulation and associated additive manufacturing method capable of realizing three-dimensional conductive polymer structures. A light-based additive manufacturing technique known as vat polymerization is …

Covalently Crosslinked Organic/Inorganic Hybrid Biomaterials For Bone Tissue Engineering Applications, Dibakar Mondal

Electronic Thesis and Dissertation Repository

Scaffolds are key components for bone tissue engineering and regeneration. They guide new bone formation by mimicking bone extracellular matrix for cell recruitment and proliferation. Ideally, scaffolds for bone tissue engineering need to be osteoconductive, osteoinductive, porous, degradable and mechanically competent. As a single material can not provide all these requirements, composites of several biomaterials are viable solutions to combine various properties. However, conventional composites fail to fulfil these requirements due to their distinct phases at the microscopic level. Organic/inorganic (O/I) class II hybrid biomaterials, where the organic and inorganic phases are chemically crosslinked on a molecular scale, hence the …

Adaption Of Catechol And Reversible Addition-Fragmentation Chain-Transfer (Raft) Chemistries For Water-Based Applications, Olabode Oyeneye

Electronic Thesis and Dissertation Repository

Incorporating the binding chemistry of catechol functionality with RAFT chemistry offers a facile and simplified approach for developing a suite of new 2D and 3D hybrid materials with tailored morphologies. Leveraging both chemistries by synthesizing catechol-end functionalized RAFT agents and catechol-containing monomeric species for RAFT (co)polymerization, this dissertation examined a new series of advanced materials that were designed for water-based applications including model flocculants, thermoresponsive hydrogels, adsorbents and underwater adhesives.

To prepare the RAFT agents, novel trithiocarbonates with several catechol end R groups (as postpolymerization anchors) were synthesized that differ in their carbonyl α-substituents (Dopa-CTAs). These materials were evaluated for …

Effects Of Lignin As A Stabilizer Or Antioxidant In Polyolefins, Afsana S. Kabir

Electronic Thesis and Dissertation Repository

Lignin, a major component of biomass, is an attractive alternative to hindered phenol-based antioxidants for polymers due to its renewable nature and naturally occurring hindered phenolic structure. In this study, for the first time, lignin de-polymerization was explored as a promising approach to improve the reactivity of the lignin-based antioxidants for polymers (polyethylene, PE and polypropylene, PP). A proprietary hydrolytic de-polymerization process was utilized to increase the antioxidant activity of two types of technical lignin: kraft lignin, KL (a by-product from the pulp and paper industry) and hydrolysis lignin, HL (a by-product from the pre-treatment processes in cellulosic ethanol plants). …

Additive Manufacturing Process Of 3d Polyaniline Transducers Via Direct Ink Writing, Frederick Benjamin Holness

Electronic Thesis and Dissertation Repository

Electroactive polymers exhibit a change in properties, typically size or shape, in response to electrical stimuli. One class of electroactive polymer of particular interest are the conjugated polymers, whose conjugated backbone structure imparts electrical conductivity. However, this structure imposes processing limitations restricting their form to 2D structures. To overcome this, we develop specially formulated polyaniline- based blends via counter-ion induced thermal doping for the fabrication of 3D conductive structures via direct ink writing. This approach employs multi-material extrusion for the production of structures with passive and active features, rapid device fabrication, and improved design freedom. A model of the thermal …

Fabrication Of Large Mechanically Flexible Multi-Layered Pdms Optical Devices, Robert S. Green

Electronic Thesis and Dissertation Repository

Mechanically flexible large area polydimethylsiloxane (PDMS) optical devices are fabricated using soft-lithography techniques based on replica moulding. These non-rigid optical devices can be designed as sheets to act as either light concentrators (collectors) or diffusers (illuminators) based on the position and geometry of micro-optical structures (MOSs) embedded within the sheet or imprinted on its surface. The active surface area of the device can range from less than a sq. cm to several sq. m. The performance of the large area optical device is a function of the location and geometry of micro-optical structures, thickness and shape of the flexible waveguide, …

Catalytic Conversion Of Fructose, Glucose And Industrial Grade Sugar Syrups To 5-Hydroxymethylfurfural, A Platform For Fuels And Chemicals, Sadra Souzanchi

Electronic Thesis and Dissertation Repository

5-hydroxymethylfurfural (HMF) as a versatile and polyfunctional compound derived from dehydration of biomass has attracted increasing attentions in research over the past decades. HMF is an important intermediate and platform chemical, which can be converted into different useful chemicals as well as the promising biofuels. It can be obtained from acid-catalyzed dehydration of different C₆-based carbohydrates such as glucose, fructose, sucrose and cellulose.

In this thesis, a cost-effective process for catalytic conversion of simple sugars (particularly glucose and fructose) and industrial grade sugar syrups to HMF was studied in a novel biphasic continuous-flow tubular reactor using inexpensive heterogeneous …

Studies On Nanocomposite Coating Produced By Laser-Assisted Process To Prevent Silicone Hydrogels From Bio-Fouling, Vishnuvardhana Wuppaladhodi

Electronic Thesis and Dissertation Repository

In this thesis, silver nanoparticles incorporated into polyvinylpyrrolidone (PVP) were deposited on silicone hydrogel to improve the hydrophilicity of the silicone hydrogel and prevent the growth of bacteria. Two different processes were employed to produce Ag nanoparticles: (1) Process-A is a photochemical reduction; (2) Process-B is laser ablation in liquid. Following that, MAPLE process was employed to deposit the Ag-PVP nanocomposites on the surface of silicone hydrogel. A solid-state pulsed laser (Nd:YAG) with a wavelength of 532 nm at a fluence of 50.4 mJ/cm² was used in the MAPLE system to deposit Ag-PVP nanocomposite coating. Our results indicate that …

Production Of Bio-Based Phenol Formaldehyde Foams, Bing Li

Electronic Thesis and Dissertation Repository

Considering the declining non-renewable fossil resources, there is increasing interest in the development of more environmentally conscious, sustainable and cost-effective substitutes for chemical production. Lignin, a main component in lignocellulosic biomass, has been considered to be a potential substitute for petroleum-based phenol due to its phenolic structure.

This PhD dissertation aimed at producing bio-based phenol formaldehyde (BPF) foams using bio-phenols, including but not limited to, kraft lignin (KL), organosolv lignin (OL), hydrolysis lignin (HL), and bio-crude oil from white birth bark. The challenge of the existing process of producing BPF foams is that a low phenol substitution ratio, generally less …

Engineered Quantum Dots For Eva Nanocomposite Films And Tio2 Photocatalysts, Md Abdul Mumin

Electronic Thesis and Dissertation Repository

Light absorbing inorganic nanoparticles in transparent plastics such as poly(ethylene-co-vinyl acetate) (EVA) are of enormous interest in emerging solar materials, including photovoltaic (PV) modules and commercial greenhouse films. Quantum dots (QDs) have the potential to absorb UV light and selectively emit visible light. However, how to stabilize the QDs for long product life spans without "blinking" while enabling their easy integration into polymer systems is lacking. This work examines different approaches for loading mesoporous silica encapsulated QDs into EVA polymer films which can control plant growth in greenhouses or enhance PV panel efficiencies.

Highly luminescent CdS and CdS-ZnS core-shell QDs …

Exploring The Chemistry Of Phosphorus For Photopolymer Applications, Ryan Guterman

Electronic Thesis and Dissertation Repository

Prior to this thesis, phosphorus-containing polymers and photopolymerization represented two distinct, non-overlapping fields of study. This thesis examined the prospect of combining these two approaches to create a system possessing the benefits of both techniques. By exploiting the chemistry of phosphorus, and using photopolymerization as a fabrication method, new materials were developed and assessed for their use in various applications.

Among the many phosphorus compounds that may be used in polymer science, phosphonium salts and primary phosphines were of specific focus. First, highly fluorinated phosphonium monomers were developed to create photopolymerized hydrophobic surfaces. A structure-activity relationship was established, as both …

Synthesis, Characterization And Applications Of Lignin-Based Epoxy Resins, Fatemeh Ferdosian

Electronic Thesis and Dissertation Repository

Epoxy resin is one of the most versatile thermosetting polymers with diverse applications. Epoxy resins are mainly produced from the reaction of bisphenol-A (BPA) and epichlorohydrin. The consumption of bisphenol-A is facing growing concerns over its carcinogenic effects and its sustainability. Lignin can be a promising renewable substitute of bisphenol-A in the synthesis of epoxy resins.

In this thesis work, a novel method has been developed for the synthesis of bio-based epoxy resins with reduced side reactions, employing de-polymerized lignin from organosolv lignin (DOL), kraft lignin (DKL) and hydrolysis lignin (DHL) under alkaline condition in the presence of a phase …

Production And Applications Of Formaldehyde-Free Phenolic Resins Using 5-Hydroxymethylfurfural Derived From Glucose In-Situ, Yongsheng Zhang

Electronic Thesis and Dissertation Repository

The phenol-formaldehyde (PF) resin manufacturing industry is facing a growing challenge with respect to concerns over human health, due to the use of carcinogenic formaldehyde and sustainability due to the use of petroleum-based phenol in PF resin manufacture. Glucose and its derivative, 5-hydroxymethylfurfural (5-HMF), have proven to be potential substitutes for formaldehyde in the synthesis of phenolic novolac resins.

This thesis investigated a number of glucose and 5-HMF resin systems including the curing of phenol-glucose novolac resin (PG) with a bis-phenol-A type epoxy. The curing process was modeled according to the Sestak-Berggren equation (S, B) using Málek methods. This was …

On The Interfacial Fracture Mechanics Of Long-Fibre Reinforced Polymer Composites, Ian N. Swentek

Electronic Thesis and Dissertation Repository

Fibre-reinforced polymer composites are being widely adopted as the de facto material for automotive lightweight design, but lack the material models capable of accurately predicting fracture. To address this research gap, three large-scale experimental studies are undertaken to characterize thermoset polymers during cure, understand the fibre-matrix interfacial bond strength, and predict the fracture of random long-fibre composites via the energy of fracture. In conjunction with the Fraunhofer Project Center in London, Ontario, sample sheet moulded composites were used to verify the key findings with several industrial composite samples. With refined interfacial strength measurement methods, and accurate predictions of the composite …

Humidity Effect On The Structure Of Electrospun Core-Shell Pcl-Peg Fibers For Tissue Regeneration Applications, Adam P. Golin

Electronic Thesis and Dissertation Repository

With the aim of creating a biodegradable scaffold for tympanic membrane (TM) tissue regeneration, core-shell nanofibers composed of a poly(caprolactone) shell and a poly(ethylene glycol) core were created using a coaxial electrospinning technique. In order to create fibers with an optimal core-shell morphology, the effect of relative humidity (RH) on the core-shell nanofibers was systematically studied, with a FITC-BSA complex encapsulated in the core to act as a model protein. The core-shell nanofibers were electrospun at relative humidity values of 20, 25, 30, and 40% RH within a glove box outfitted for humidity control. The core-shell morphology of the fibers …