Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- Albedo (1)
- Bifacial (1)
- Carbon Fiber Reinforced Polymers (1)
- Covalent adaptable networks (1)
- Degradation (1)
-
- Delamination (1)
- Dynamic bonding (1)
- Interlaminar Tensile Strength (1)
- LDPE (1)
- Microplastics (1)
- Mulch (1)
- Photovoltaic (1)
- Plastic pollution (1)
- Polyethylene (1)
- Polymer (1)
- Stress relaxation (1)
- Surface characterization (1)
- Thermoset Matrix (1)
- Triazabicyclodecene (1)
- Twill Weave (1)
- Unidirectional (1)
- Wood coatings (1)
Articles 1 - 4 of 4
Full-Text Articles in Engineering
Effect Of Environmental And Ultraviolet Degradation On The Albedo Of Polyethylene Sheet Materials For Improved Energy Harvesting By Bifacial Photovoltaic Power Plants, William A. Jang, Roxy H. Jackson-Gain
Effect Of Environmental And Ultraviolet Degradation On The Albedo Of Polyethylene Sheet Materials For Improved Energy Harvesting By Bifacial Photovoltaic Power Plants, William A. Jang, Roxy H. Jackson-Gain
Materials Engineering
Solar energy farms typically utilize monofacial photovoltaic (mPV) cells in their arrays to capture direct sunlight to produce renewable energy. However, the efficiency of these farms can be increased by 2 – 6% through the implementation of bifacial photovoltaic cells (bPV). These bPV cells function by capturing incident ultraviolet (UV) light energy that is reflected off the surface to increase its overall energy production. The amount of UV energy that is reflected is dependent on the albedo value of surface, which is a measure of energy reflectance. In this study, samples of unreinforced polyethylene (PE), scrim-reinforced polyethylene (SR-PE), and woven …
Covalent Adaptable Networks For Wood Coatings, Jachin Boaz Clarke
Covalent Adaptable Networks For Wood Coatings, Jachin Boaz Clarke
Materials Engineering
Wood swells and shrinks causing problems with seasonal humidity. Applying thick coatings of reactive finishes based on cross-linked polyurethane, epoxy, or polyesters can slow moisture-vapor exchange. However, the use of thick coatings leads to cracking and crazing sooner than thin finishes. This research proposes the addition of 3.3 mol % triazabicyclodecene, a conventionally used covalent adaptable network catalyst, in a commercially available polyester-based wood coating. The self-healing of the wood coating is tested using DMA stress relaxation and compression molding. The result from DMA renders inconclusive and compression molding indicates the novel wood coating oxidizes at elevated temperatures. The wood …
Surface Characterization Of Low-Density Polyethylene Mulch, Risha Shah
Surface Characterization Of Low-Density Polyethylene Mulch, Risha Shah
Materials Engineering
Plastic pollution in aquatic systems has traditionally been highlighted in past and current research due to the increase in plastic production every year. Unfortunately, quantitative and qualitative data regarding plastic pollution on land systems such as agricultural mulch is limited. Agricultural mulch breaks down into macroplastics and then degrades into microplastics. The microplastics investigated in this study are all secondary microplastics: microplastics that form due to weathering of larger fragments of plastic. Weathering can occur due to a variety of factors; however, UV radiation and mechanical weathering have been the factors of focus on most current research in microplastic formulation. …
Interlaminar Tensile Properties Of Unidirectional And Woven Carbon Fiber Reinforced Toughened Epoxy Laminates, Eric Timothy Casey, Sean Mckalip Thompson
Interlaminar Tensile Properties Of Unidirectional And Woven Carbon Fiber Reinforced Toughened Epoxy Laminates, Eric Timothy Casey, Sean Mckalip Thompson
Materials Engineering
This project aims to develop a dataset on interlaminar tensile strength comparing unidirectional and woven thermoset matrix carbon fiber composites keeping ply count, matrix material, and fiber diameter constant. The interlaminar tensile strength is an important property relating to the delamination failure mode. Interlaminar tensile strength is determined using the ASTM D6415 testing standard. This test is a modified four-point bend test using a 90° curved beam test specimen. Laminates were produced by laying up pre-impregnated carbon fiber sheets onto a curved beam tooling. The unidirectional laminate was produced with 20 plies in a [0,0,90,0,0]4 layup pattern. The woven …