Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 5 of 5
Full-Text Articles in Engineering
Characterization Of Metal Contacts On Hydrothermally Synthesized Uranium Dioxide For Novel Semiconductor Applications, Tory E. Robinson
Characterization Of Metal Contacts On Hydrothermally Synthesized Uranium Dioxide For Novel Semiconductor Applications, Tory E. Robinson
Theses and Dissertations
This research is focused on determining which metals or combinations of metals form effective electrical contacts on hydrothermally synthesized UO2 substrates to allow for additional work in characterization of the material as well as the feasibility of its use in semiconductor devices such as solid-state neutron detectors. A methodology was established for selection of candidate metals. Target mixtures composed of Au, Ag, Pt, and Mg were chosen along with several single-metals. Thin metal films were deposited onto tungsten probe tips and hydrothermally synthesized UO2 samples to allow for analysis of mechanical and deposited contact to the substrates through I-V measurements.
Improved Fabrication For Micromirror Arrays, Enoc Flores
Improved Fabrication For Micromirror Arrays, Enoc Flores
Theses and Dissertations
Micromirror devices which consisted of one SU-8 2050 layer, two different exposures, and a series of metal depositions were constructed and evaluated. By varying the exposure, a micromirror structure was fabricated with different thicknesses, a ratio of 1.083 µm/(mJ/cm2) was found. The initial design consisted of four layers. The pillar was made of one SU-8 layer, and the top portion had three layers in the following order: gold, SU-8, and gold. This design could not be released and did not have characteristics of a flat and conformal reflective surface. Several variations of the initial design were explored and all of …
Displacement Damage Effects In Gesn Light Emitting Diodes, Kevin K. Choe
Displacement Damage Effects In Gesn Light Emitting Diodes, Kevin K. Choe
Theses and Dissertations
Potential future use on Earth-orbiting satellites calls for investigation into the suitability of GeSn based photonic devices in high energy proton environments. The electroluminescence (EL) intensity of Ge1-xSnx (x = 0, 0.02, 0.069, and 0.094) light emitting diodes was measured before and after irradiation by 2 MeV protons at relatively high fluence levels. The results showed that GeSn devices with higher Sn content were up to 10 times more resistant against proton displacement damage than the pure Ge (x = 0) devices. As Sn concentration increased, the band gap decreased, and V-P hole trap energy level moved further from the …
Analysis And Design Of Modular Overhead Protection System Utilizing Readily Available Materials, Zachary J. Spranger
Analysis And Design Of Modular Overhead Protection System Utilizing Readily Available Materials, Zachary J. Spranger
Theses and Dissertations
This research investigated passive overhead protective measures for existing facilities in an urban environment that are vulnerable to enemy munitions fire. A new modular structural system was designed utilizing commercially available construction material consisting of structural tubing, scaffolding clamps, base plates, and simple roofing components. Structural analysis software was used to model nine modular structures to understand the relationship between the load bearing capacity of the structural members and overall dimensions of the system. Environmental variables for the models were set to the Parwan Province in Afghanistan; this region presents worst-case scenarios both for environmental factors and threat of enemy …
Scaling Film Cooling Adiabatic Effectiveness With Mass Transfer And Thermal Experimental Techniques, Luke J. Mcnamara
Scaling Film Cooling Adiabatic Effectiveness With Mass Transfer And Thermal Experimental Techniques, Luke J. Mcnamara
Theses and Dissertations
With increasing engine temperatures, it is becoming more important to design effective film cooling schemes. Low temperature, large scale tests are often implemented in the design process to reduce cost and complexity. A nondimensional adiabatic effectiveness can be used as an indication of the performance of a film cooling scheme. However, the coolant flow rate must be properly scaled between the low temperature tests and engine temperatures to accurately predict film cooling effectiveness. This process is complicated by gas property variation with temperature. Tests are commonly conducted using thermal measurement techniques with infrared thermography (IR), but the use of pressure …