Engineering Commons^™

An Investigation Into Applications Of Canonical Polyadic Decomposition & Ensemble Learning In Forecasting Thermal Data Streams In Direct Laser Deposition Processes, Jonathan Storey

Theses and Dissertations

Additive manufacturing (AM) is a process of creating objects from 3D model data by adding layers of material. AM technologies present several advantages compared to traditional manufacturing technologies, such as producing less material waste and being capable of producing parts with greater geometric complexity. However, deficiencies in the printing process due to high process uncertainty can affect the microstructural properties of a fabricated part leading to defects. In metal AM, previous studies have linked defects in parts with melt pool temperature fluctuations, with the size of the melt pool and the scan pattern being key factors associated with part defects. …

Monitoring Additive Manufacturing Machine Health, Jeremy Hale

Doctoral Dissertations

Additive manufacturing (AM) allows the production of parts and goods with many benefits over more conventional manufacturing methods. AM permits more geometrically complex designs, custom and low-volume production runs, and the flexibility to produce a wide variety of parts on a single machine with reduced pre-production cost and time requirements. However, it can be difficult to determine the condition, or health, of an AM machine since complex designs can increase the variability of part quality. With fewer parts produced, destructive testing is less desirable and statistical methods of tracking part quality may be less informative. Combined with the relatively more …

Part Design Geometry-Driven Toolpath Optimization For Additive Manufacturing Energy Sustainability Improvement, David Kolawole Somade

Graduate Research Theses & Dissertations

One of the most promising new manufacturing technologies in the past three decades isadditive manufacturing (AM), also commonly known as three-dimensional (3D) printing or rapid prototyping. The energy consumption problem in AM can be significant when it is adopted at the industrial scale or used under resource-restricted conditions. The energy consumption of an AM process is influenced by several factors including bed heating, filament extrusion, material infill, component cooling, etc. All these factors are further determined by the equipment and the toolpath for a specific printing task. Build orientation and tool-path direction are frequently used to optimize part and process …

Functionally Magnetic Gradient Copper-Nickel Material Fabricated Via Directed Energy Deposition, Vy Tran Phuong Nguyen

Graduate Theses, Dissertations, and Problem Reports

Functionally gradient materials (FGMs) of CuSn10 and Inconel 718 were fabricated via a hybrid directed energy deposition (DED) system. The objective of the present thesis is to determine the feasibility of manufacturing CuSn10 and Inconel 718 FGMs via DED and investigate the physical and mechanical properties and the microstructures of the resulting FGMs. The physical tests comprised of conductivity and Seebeck coefficient measurements. The microstructure analysis and mechanical testing include microscopic imaging, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and hardness test. In addition, compressive strength test was performed to analyze the interface bonding behaviors.

Identifying An Optimization Technique For Maker Usage To Address Covid-19 Supply Shortfalls, Michael J. Wilson

Doctoral Dissertations

Fused Deposition Modeling (FDM) can be purchased for under five hundred dollars. The availability of these inexpensive systems has created a large hobbyist (or maker) community. For makers, FDM printing is used numerous uses.

With the onset of the COVID-19 pandemic, the needs for Personal Protective Equipment (PPE) skyrocketed. COVID-19 mitigation strategies such as social distancing, businesses closures, and shipping delays created significant supply shortfalls. The maker community stepped in to fill gaps in PPE supplies.

In the case of 3DP, optimization remains the domain of commercial entities. Optimization is, at best, ad-hoc for makers. With the need to PPE …

Quality Assurance Of Lightweight Structures Via Phase-Based Motion Estimation, Ikenna E. Ifekaonwu

Electronic Theses and Dissertations

In recent years, lightweight structures have become mature and adopted in various applications. The importance of quality assurance cannot be overemphasized hence extensive research has been conducted to assess the quality of lightweight structures. This study investigates a novel process that exploits motion magnification to investigate the damage characteristics of lightweight mission-critical parts. The goal is to assure the structural integrity of 3D printed structures and composite structures by determining the inherent defects present in the part by exploiting their vibration characteristics. The minuscule vibration of the structure was recorded with the aid of a high-speed digital camera, and the …

Parametric Study Of Residual Stresses In Wire And Arc Additive Manufactured Parts, Hisham Khaled Jamil Abusalma

Mechanical & Aerospace Engineering Theses & Dissertations

Wire and Arc Additive Manufacturing (WAAM) is a cost-effective additive manufacturing process due to its capability to fabricate large metal parts with high deposition rate and low equipment cost. Although this method is gaining popularity in manufacturing industry, more research is needed to understand process parameters’ effects on residual stress (RS) distribution and part distortion. As such, a 3D thermo-elastic-plastic transient model was established in ABAQUS and employed to investigate the effect of process parameters such as the torch speed, the deposition power and the interlayer dwell time on RS distribution and distortion in WAAM part. The numerical model utilized …

3d Printing For Solving Part Obscolescence, Ayman G. Alqarni

Theses and Dissertations

The purpose of this research was to highlight the issue of parts obsolescence and to highlight the possibility of using alternative methods to overcome parts shortage. Specifically, this thesis sought to answer the research question: is the three-dimensional printing technology (3D) an applicable approach to overcome part obsolescence. The research question was answered through data research and survey analysis. Notwithstanding, the diminished manufacturing sources and material shortages (DMSMS) management and other existing approaches, such as forecasting, contracting, and reverse engineering (RE), were discussed briefly in the literature review and profoundly in chapter IV to differentiate among applicable existing solutions toward …

Determining The Efficacy Of Additive Manufacturing For The Aerospace Spare Parts Supply Chain, Kyle O'Brien

Electronic Theses and Dissertations

This thesis investigates how additive manufacturing (AM) based on-demand part production can supplement or replace the traditional production and inventory in typical aerospace’s spare parts supply chain systems. This study focuses on the operational characteristics of AM and its impacts on the overall logistics of plant-level operations. To capture the microscopic operational aspects of the AM production, a discrete-event simulation based approach was adopted, with key AM operation resources (e.g. AM system, operator) and attributes (e.g. AM manufacturing speed, individual part characteristics and demands) accounted for in the modeling process. In addition, a benchmark warehouse inventory model was also established …

Freeform Extrusion Fabrication Of Advanced Ceramics And Ceramic-Based Composites, Wenbin Li

Doctoral Dissertations

"Ceramic On-Demand Extrusion (CODE) is a recently developed freeform extrusion fabrication process for producing dense ceramic components from single and multiple constituents. In this process, aqueous paste of ceramic particles with a very low binder content ( < 1 vol%) is extruded through a moving nozzle to print each layer sequentially. Once one layer is printed, it is surrounded by oil to prevent undesirable water evaporation from the perimeters of the part. The oil level is regulated just below the topmost layer of the part being fabricated. Infrared radiation is then applied to uniformly and partially dry the top layer so that the yield stress of the paste increases to avoid part deformation. By repeating the above steps, the part is printed in a layer-wise fashion, followed by post-processing. Paste extrusion precision of different extrusion mechanisms was compared and analyzed, with an auger extruder determined to be the most suitable paste extruder for the CODE system. A novel fabrication system was developed based on a motion gantry, auger extruders, and peripheral devices. Sample specimens were then produced from 3 mol% yttria stabilized zirconia using this fabrication system, and their properties, including density, flexural strength, Young's modulus, Weibull modulus, fracture toughness, and hardness were measured. The results indicated that superior mechanical properties were achieved by the CODE process among all the additive manufacturing processes. Further development was made on the CODE process to fabricate ceramic components that have external/internal features such as overhangs by using fugitive support material. Finally, ceramic composites with functionally graded materials (FGMs) were fabricated by the CODE process using a dynamic mixing device"--Abstract, page iv.

In Silico Analysis Of Advanced Processing Methods For Light-Weight Alloys Powders, Marjan Nezafati

Theses and Dissertations

Light-weight Al and Mg-based metal-matrix nanocomposites (MMNCs) are lauded as one of the most promising structural materials for vehicle, military, and construction applications. These MMNCs are often synthesized using the powder metallurgy (PM) process under liquid nitrogen cryogenic environments to control the grain sizes. It is believed that proper incorporation of the nitrogen species into the bulk lattice during processing could strongly enhance the mechanical properties of MMNCs by forming N-rich dispersoids. In this work, using the density-functional theory (DFT), the adsorption, absorption and diffusion behavior of nitrogen molecule/atoms have been studied and related to t Al and Mg MMNC …

Binder Jetting Additive Manufacturing Process Fundamentals And The Resultant Influences On Part Quality., Hadi Miyanaji

Electronic Theses and Dissertations

Binder jetting additive manufacturing (BJ-AM) technology is a process by which a part is fabricated layer by layer through depositing liquid binder in the designated regions of each layer until the feature is complete. Due to the use of binder in geometry generation, this process possesses various advantages over the other additive manufacturing technologies including the ability to create colored objects via colored binders, lower cost, lack of heat-induced defects, and its potential capability to print a variety of materials such as metals, sands and ceramics. Although the application of the binder jetting process has been recently reported by different …

Tooling For Injection Molding Using Laser-Powder Bed Fusion., Mohith Ram Buxani

Electronic Theses and Dissertations

Laser-Powder Bed Fusion (L-PBF) has been considered for some time by the injection molding industry for the fabrication of tooling for injection molding in order to address large lead times and costs for tool-making. Computer-aided simulations are also routinely used to evaluate new part and mold designs as well as understanding the effects of material compositions and processing conditions on part quality and overall productivity. However, there remains a significant need to integrate the perspectives from injection molding, 3D printing, metal powders, and component design and process simulation to better utilize LPBF for fabricating tooling required for injection molding. The …

Ultrasonic Nondestructive Evaluation Of Metal Additive Manufacturing., Venkata Karthik Nadimpalli

Electronic Theses and Dissertations

Metal Additive Manufacturing (AM) is increasingly being used to make functional components. One of the barriers for AM components to become mainstream is the difficulty to certify them. AM components can have widely different properties based on process parameters. Improving an AM processes requires an understanding of process-structure-property correlations, which can be gathered in-situ and post-process through nondestructive and destructive methods. In this study, two metal AM processes were studied, the first is Ultrasonic Additive Manufacturing (UAM) and the second is Laser Powder Bed Fusion (L-PBF). The typical problems with UAM components are inter-layer and inter-track defects. To improve the …

Viability Of Additive Manufacturing For Production And Tooling Applications: A Development Of The Business Case, Christopher Charles Griffin

Masters Theses

As marketplace competition drives industrial innovation to increase product value and decrease production costs, emerging technologies foster a new era through Industry 4.0. One aspect of the movement, additive manufacturing, or 3D [three-dimensional] printing, contains potential to revolutionize traditional manufacturing techniques and approach to design. However, uncertainties within the processes and high investment costs deter corporations from implementing and developing the technology. While several industries are benefitting from additive manufacturing’s current state, as the technology continues to progress, more companies will need to evaluate it for industrial viability and adoption. As such, there exists a need for a framework to …

The Effect Of Process Parameters And Surface Condition On Bond Strength Between Additively Manufactured Components And Polymer Substrates, Bharat Bhushan Chivukula

Graduate Theses and Dissertations

Additive patching is a process in which printers with multiple axes deposit molten material onto a pre-defined surface to form a bond. Studying the effect of surface roughness and process parameters selected for printing auxiliary part on the bond helps in improving the strength of the final component. Particularly, the influence of surface roughness, as established by adhesion theory, has not been evaluated in the framework of additive manufacturing (AM). A full factorial design of experiments with five replications was conducted on two levels and three factors, viz., layer thickness, surface roughness, and raster angle to examine the underlying effects …

Evaluation Of The Impact Of An Additive Manufacturing Enhanced Cubesat Architecture On The Cubesat Development Process, Rachel E. Sharples

Theses and Dissertations

Additive manufacturing (AM) is a fabrication method ideally suited to low-quantity, highly customized builds, leading to interest in its application to satellite development and manufacturing, where each build is unique. Due to the issues of long development schedules and high development and manufacturing costs, methods are needed in the CubeSat development process to reduce the weight and volume of subsystems and decrease integration time. The work develops an architecture for an AM-augmented CubeSat and examines the AM techniques of embedded electronics, embedded thrusters, and custom radiation-hardened materials can impact the subsystems of a CubeSat. The AM-augmented architecture shows a shift …

Determining The Degree Of The Routinization Of Additive Manufacturing In The Air Logistics Complexes, Candis A. Woods

Theses and Dissertations

Fiscal constraints have affected the USAF’s spending and sustainment of weapons systems that are being utilized beyond their programmed life cycle; therefore, it is imperative that processes be given the critical eye for improvement, innovative approaches, and/or best practice implementation. The AFSC, part of the AFMC, has embarked on a groundbreaking effort to transform operations and leverage industry best practices, while maintaining focus on warfighter support to create “The AFSC Way.” The AFSC Way is based on a shared leadership model that emphasizes speed, safety, and quality, which gives way to innovative ideas and new technologies in order to achieve …

A Heuristic Algorithm For Determining The Part Set In A Powder-Bed Additive Manufacturing Machine., Sonja Dieder

Electronic Theses and Dissertations

The goal of this research is to develop a procedure for the placement of a priority part into a planned build in a powder-bed additive manufacturing machine. Toward that goal, a heuristic procedure was developed that seeks to maximize the revenue in a scheduled build, subject to due-date constraints; i.e., all parts with the closest due date will not only be included in the build, but will be placed near the bottom of the build. Likewise, any part in the scheduled build that does not have an immediate due date is a candidate for removal in order to accommodate a …